Multitech MT1932ZDXI Command Reference Manual page 63

N – Modulation Handshake ..........................11
O – Return Online to Data ............................11
P – Pulse Dialing ..........................................11
\Q – Local Flow Control Selection ................19
Q – Result Codes Enable/Disable................11
Sr= – Set Register Value..............................12
\T – Inactivity Timer ......................................19
T – Select Tone Dialing ................................12
\V – Protocol Result Code ............................19
V – Result Code Format ...............................12
W – Result Code Options .............................12
X – Select Result Code & Call Monitor
Progress....................................................13
\X – XON/XOFF Pass-Through ....................19
Z – Reset and Recall Stored Profile .............13
AT Commands
Enter key ........................................................7
Attention code command - AT ...........................7
Automatic Hang-Up Control – +VNH= .............44
B
Backspace character – S5 ...............................37
Beep Tone Duration Timer (DTMF/Tone
Generation Duration) – +VTD= ....................52
Bell 212A mode..................................................7
Break Control – \K............................................18
Break Handling in Error Control – +EB ............26
C
Call Termination Buffer Management – +ETBM
......................................................................27
Callback Attempts – #CBA...............................35
Callback Delay – #CBD....................................35
Callback Enable/Disable – #CBS.....................34
Callback Failed Attempts Display – #CBF? .....35
Callback Failed Attempts Reset – #CBFR .......35
Callback Parity – #CBP....................................36
Callback Security Reset – #CBR .....................34
Caller ID Selection – +VCID.............................34
Carriage return character – S3 ........................37
Carrier loss disconnect time – S10 ..................37
Command mode.................................................6
Command Speed Response %S .....................21
Command string.................................................6
Communication Standard Setting – B................7
Complete List of Capabilities Request – +GCAP
......................................................................28
Count Rings – S1 .............................................37
Country Code Display ......................................10
Country of Installation – +GCI..........................28
D
Data buffering...................................................16
Data Calling Tone – -C.....................................19
Data Carrier Detect – &C .................................14
Data Compression Control – %C.....................20
Data mode..........................................................6
Data Set Ready Control – &S ..........................16
Diagnostic Information Display ........................10
Dial – D...............................................................8
Multi-Tech Systems, Inc. AT Commands for the MultiModem & SocketModem MT9234 Series (S000434D)
Dial string modifiers ........................................... 8
Dialing tones – S11.......................................... 37
Distinctive Ring (Ring Cadence Reporting) –
+VDR=.......................................................... 53
Distinctive Ring Report – +VDR= .................... 33
Downstream Data Rate – S38 ........................ 38
DTE/DCE Interface Rate (Turn Off Autobaud) –
+VPR=.......................................................... 56
DTE/DCE Interface Rates................................ 61
DTE-DCE Local Flow Control – +IFC .............. 29
DTE-DCE Local Rate Reporting – +ILRR........ 29
DTR Control – &D ............................................ 14
DTR Dialing – $D ............................................. 32
E
Echo Command – E........................................... 9
Enable/Disable Voice Mode Packet Protocol –
+VPP= .......................................................... 56
Enter key............................................................ 7
Enter Setup Password – #S............................. 34
Enter Voice Receive State – +VRX ................. 44
Error control – S36........................................... 37
Error control – S48........................................... 39
Error Control Report – +ER ............................. 26
Error Control Selection – +ES.......................... 27
Error Correction Mode – \N.............................. 18
Escape sequence .............................................. 6
Escape Sequence – S2 ................................... 37
Escape sequence +++AT .................................. 7
Event Reporting and Masking – +VEM= ......... 54
F
Fallback and Fall Forward – %E...................... 21
Fallback in N command ................................... 11
Fax Class Indication – +FCLASS .................... 28
Fax commands .................................................. 6
Firmware Version Display................................ 10
Fixed DTE Rate – +IPR= ................................. 29
Flow Control..................................................... 57
Flow Control Assert and Deassert Points –
+VBT= .......................................................... 55
Flow Control Selection – &K ............................ 15
H
Handshake....................................................... 11
Hook Control – H ............................................... 9
I
Inactivity timer – S30........................................ 37
Inactivity Timer – \T.......................................... 19
Inactivity Timer – VIT= ..................................... 47
Initialization strings............................................. 6
Initialize Voice Parameters – +VIP .................. 44
Interface Configuration commands
+VBT= – Flow Control Assert and Deassert
Points........................................................ 55
+VPP= – Enable/Disable Voice Mode Packet
Protocol..................................................... 56
+VPR= – DTE/DCE Interface Rate (Turn Off
Autobaud) ................................................. 56
Index
63