General Service; Spark Arrestor - Cub Cadet Pro Z SurePath Auto Steer Series Operator's Manual

• If necessary, use a funnel to avoid spillage.
• Replace fuel cap and tighten securely.
• If fuel is spilled, wipe off the engine and equipment. Wait 5 minutes before
starting the engine.
• To reduce fire hazards, keep machine free of grass, leaves, or other debris build-
up. Clean up oil and fuel spillage and remove any fuel soaked debris.
• Never store the machine or fuel container inside where there is an open flame,
spark, or pilot light as on a water heater, space heater, furnace, clothes dryer, or
other gas appliance.

GENERAL SERVICE

1. Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless and deadly gas.
2. Before cleaning, repairing, or inspecting, make certain the blade(s) and all moving
parts have stopped. Turn off the engine, remove the key, and disconnect the spark
plug wire(s) and negative battery cable to prevent unintended starting.
3. Periodically check to make sure the blades come to a complete stop within
approximately 7 seconds after operating the blade disengagement control. If the
blades do not stop within this time frame, your machine should be serviced.
4. Never tamper with the safety interlock system or other safety devices.
5. Regularly check the safety interlock system for proper function, as described later
in this manual. If the safety interlock system does not function properly, have
your machine serviced.
6. Check brake operation frequently as it is subjected to wear during normal
operation. Adjust and service as required.
7. Check the blade(s) and engine mounting bolts at frequent intervals for proper
tightness. Also, visually inspect blade(s) for damage (e.g., excessive wear, bent,
cracked). Replace the blade(s) with the original equipment manufacturer's
(O.E.M.) blade(s) only, listed in this manual. Use of parts which do not meet
the original equipment specifications may lead to improper performance and
compromise safety!
8. Mower blades are sharp. Wrap the blade or wear gloves, and use extra caution
when servicing them.
9. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe
working condition.
10. After striking a foreign object (or if abnormal vibration occurs), stop the blades
and engine and thoroughly inspect the machine for any damage. Make necessary
repairs before resuming operation.
11. Never attempt to make adjustments or repairs to the machine while the engine
is running.
12. Grass catcher components and the discharge cover are subject to wear and
damage which could expose moving parts or allow objects to be thrown. For
safety protection, frequently check components and replace immediately with
original equipment manufacturer's (O.E.M.) parts only, listed in this manual. Use
of parts which do not meet the original equipment specifications may lead to
improper performance and compromise safety!
13. Do not change the engine governor settings or over-speed the engine. The
governor controls the maximum safe operating speed of the engine.
14. Maintain or replace safety and instruction labels, as necessary.
15. Observe proper disposal laws and regulations for gas, oil, etc. to protect
the environment.
SAFE OPERATION PRACTICES
6
DO NOT MODIFY ENGINE
To avoid serious injury or death, do not modify engine in any way. Tampering with
the governor setting can lead to a runaway engine and cause it to operate at unsafe
speeds. Never tamper with factory setting of engine governor.
NOTICE REGARDING EMISSIONS
This machine is equipped with an engine that is certified to federal EPA emission
standards for non-road engines and equipment, and where applicable to California
Air Resources Board (CARB) emission standards. The Engine Operator's Manual is
supplied by the engine manufacturer, and provides additional information relating
to the emission system, warranty, and maintenance of the engine in accordance with
EPA and/or CARB regulations. Making any unauthorized alterations or modifications
to the engine, fuel, or venting systems may violate EPA and CARB regulations.
When required, models are equipped with low permeation fuel lines and fuel
tanks for evaporative emission control. California models may also include a carbon
canister. Please contact Customer Support for information regarding the evaporative
emission control configuration for your model.
This machine is designed to run on regular, unleaded gasoline, 87 octane or higher.
Never use gasoline containing methanol or gasoline containing more than 10%
ethanol (i.e., E15 or E85 fuels) because the fuel system may be damaged.

SPARK ARRESTOR

This machine is equipped with an internal combustion engine and should
not be used on or near any unimproved forest-covered, brush-covered, or
grass-covered land unless the engine's exhaust system is equipped with a
spark arrestor meeting applicable local or state laws (if any).
If a spark arrestor is used, it should be maintained in effective working order by the
operator. In the State of California the above is required by law (Section 4442 of the
California Public Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrestor for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131, Cleveland,
Ohio 44136-0019.
WARNING