Page 3
Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Menu Bar ...15 Sub-Menus ...16 Chapter 3 – Configuration ...17 Using the Setup Wizard to Configure the RouteFinder...17 RF820/RF820-AP and RF830/RF830-AP Wizard Setup ...18 Save & Restart Button Under Menu Bar...22 Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Contents...
• One RouteFinder CD which contains RouteFinder documentation and Adobe Acrobat Reader. If any of the items is missing or damaged, please contact Multi-Tech Systems, Inc. RouteFinder Documentation The Quick Start Guide The Quick Start Guide is a shorter version of this User Guide. It is included in printed form with your RouteFinder.
Lights when a successful connection to the 100BaseT WAN is established. Off when connected to the 10BaseT. WAN Link / ACT Lights when the WAN port has a valid Internet connection. Blinks when it is receiving or transmitting data. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide...
Serial (RF820s only) Serial port connects to a standard modem (optional). 12VDC Power The power port connects the AC power adapter. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Chapter 1 – Introduction and Description...
If one port were to go down, the RouteFinder appliance would automatically re-route all Internet and VPN traffic to the other connection. The second WAN port greatly enhances performance and system uptime. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide...
Use the cabling procedures above and attach the wireless antenna. See the Back Panel section earlier in this chapter for the location of the antenna connector. Note: The antenna must be attached in order for the RouteFinder to be operational. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Chapter 2 – Installation...
Use the cabling procedures above and attach the wireless antenna. See the Back Panel section earlier in this chapter for the location of the antenna connector. Note: The antenna must be attached in order for the RouteFinder to be operational. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide...
VSWR: Polarization: Maximum Power: Impedance: Connector: See the User Guide for the antenna's environmental and mechanical specifications. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide 2400 to 2500 MHZ 4.5dBi (nominal) ≤ 2 Linear, Vertical 50 Ω RP-SMA Plug Reverse Polarity Meets FCC Part 15.203 Requirements...
Click Start | Settings | Control Panel. Double-click the Network Connections icon. The Network Connections screen displays. Right-click the Local Area Connection icon and choose Properties from the drop down list. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide...
Page 13
Enter the Default gateway as 192.168.2.1 Close out of the Control Panel. Repeat these steps for each PC on your network. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Once you click the Properties button, the following screen displays. To have your...
It is recommended that you change the default password. Create your own password. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Use a safe password! Your first name spelled backwards is...
Menu Menu Menu Bar See menu categories and their submenus listed on the next page. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Chapter 2 – Installation Other Options Screen...
WLAN Subnet Settings WLAN Fixed Addresses display when you go to Network Setup > Wireless LAN and select Independent Subnet. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Network Setup IP Settings Wireless LAN WLAN Security WLAN Client Filter...
LAN workstation(s) and the Internet as shown in the example below. Important Note: An initial configuration must be completed for each type of RouteFinder functions: firewall configuration, LAN-to-LAN configuration, a LAN-to-Remote Client configuration. RouteFinder Initial Configuration Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide...
A section labeled WAN 2 displays on the RF830/RF830-AP Wizard Setup screen. • A section labeled WLAN (inset shown on the right) displays after you select Independent Subnet on the Network Setup > Wireless LAN screen. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide Chapter 3 – Configuration...
IP address. Secondary DNS In this field, enter a secondary domain server name. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide If the DHCP client is not enabled, the following message Chapter 3 – Configuration...
Page 20
DSL or cable modems or wireless connection to the Internet. The following fields display when you select PPPoE: User Name Enter the user name give by the ISP. Example: Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide user1@xyz.com or user 1 Chapter 3 – Configuration...
Page 21
If a secondary domain server name is configured, enter its name here. The servers are consulted in the order in which they are configured. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide The link will always be established. It is not dependent The link will be established only when there is data Chapter 3 –...
This is optional. You do not have to restart the RouteFinder after saving to the flash memory. Multi-Tech Systems, Inc. RF820/RF820-AP & RF830/RF830-AP Quick Start Guide If a connection is established, then the settings have been Chapter 3 – Configuration...