Panasonic KX-FP362BX Service Manual page 48

KX-FP362BX
6.2.3. SERVICE FUNCTION TABLE
Code
501 Pause time set
502 Flash time
503 Dial speed select
510 VOX time
511 VOX sense
514 Belldetectiontime
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
550 Memory clear
533 Setting the number of times that
massage transfer is redialed.
534 Setting the massage transfer/pager
call redial interval
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set
580 TAM continuous tone detection
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
Function Set Value
X 100 msec
X 10 ms
1: 10 pps
2: 20 pps
1:6 sec 2:4sec
1:High 2:Low
X100msec
1:2100 Hz
2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
00~99
001~999 sec
1:ON 2:OFF
1:OFF
2:PHASE B
3:ALL
1:ON 2:OFF
1:61% 2:67%
X number of
times
X second
X number of
rings
1:ON 2:OFF
X number of
times
X second
1:OFF
2:ALL
3:AUTO
Effective Default
Range
001~600 30
01~99 70
1, 2 1
1, 2 1
1, 2 1 When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
1~9 6
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.79).
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in THE UNIT CAN
COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS (P.79).
1, 2 1 The resolution reverts to the default when
transmission is complete.
1~4 1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
1~4 1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
See TEST FUNCTIONS (P.50).
00~99 03 Selects the number of times that message
transfer is redialed (not including the first dialing).
001~999 065 Sets the interval of message transfer/pager call
redial.
See TEST FUNCTIONS (P.50).
1, 2 2 See TEST FUNCTIONS (P.50).
1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See TEST FUNCTIONS (P.50).
See TEST FUNCTIONS (P.50).
0 See TEST FUNCTIONS (P.50).
See TEST FUNCTIONS (P.50).
See TEST FUNCTIONS (P.50).
1, 2 1 See DOCUMENT JAMS - SENDING (P.26).
See TEST FUNCTIONS (P.50).
1, 2 1 Sets the % break of pulse dialing according PBX.
00~99 05 Selects the number of times that ITS is redialed
(not including the first dial).
001~999 065 Sets the interval of ITS redialing.
01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
1, 2 1 ON : Stops TAM operation when Dial tone, etc.
are detected.
00~99 5 Selects the number of redial times during FAX
communication (not including the first dial).
001~999 065 Sets the FAX redial interval during FAX
communication.
1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to SOMETIME THERE IS A TRANSMIT
PROBLEM (P.77).
48
Remarks
----------
----------
----------
----------
----------