Table of Contents
Advertisement
Rear Panel
100-240V
50/60Hz
400 WATTS
Consumo de energia 400Wh
Consumo de energia
en modo de espera 71Wh
1
(1)
LINE CORD (120 V units only)
For your safety, we have incorporated a 3-wire line (mains) cable with proper grounding facilities. It is
not advisable to remove the ground pin under any circumstances. If it is necessary to use the 6505ii
without proper grounding facilities, suitable grounding adaptors should be used. Greatly reduced
shock hazard exists when the unit is operated with the proper grounded receptacles.
(2)
FUSE
WARNING: THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD
HAS BEEN DISCONNECTED FROM ITS POWER SOURCE. A 5 amp fuse is located within the cap of the fuse
holder. It must be replaced with the same type and value in order to avoid damage to the equipment
and to prevent voiding the warranty. If the amp repeatedly blows fuses, it should be taken to a
qualified service center for repair.
(3)
GROUND SWITCH
This is a three-position, rocker type switch which, for most applications, should be operated in
the center (zero) position. If hum or noise is noticed coming from the speaker enclosure(s) with
the Ground Switch in the center position, place the Ground Switch to positive (+) or negative (-)
to minimize hum. Should a hum/noise problem continue, consult your authorized Peavey dealer, the
Peavey factory, or a qualified service technician.
(4) BIAS TEST TERMINAL
These terminals, along with the adjustment knob behind the grill are provided to measure and adjust
the power amp tubes' bias. The bias adjustment should only be done by a
alified technician.
(5) EFFECTS SEND/EFFECTS RETURN
Signals are supplied to outboard effects or signal processing units by patching from the Effects
Send output into the outboard unit(s) and back into the Effects Return input using shielded
cables with 1/4" mono phone plugs. Only non-gain effects devices (chorus, reverb, delay, etc.)
should be used in the effects loop. If footswitch is used, "Effects" must be selected (LED
illuminated) for effects to work.
(6)
PREAMP OUT
This output can be used to send a preamp signal from the 6505 II to a mixing console, tape
recorder, etc., using a shielded instrument cable. Patching from the PREAMP OUT does not affect the
normal operation of the amplifier.
4
6
4
6
BRIGHT
CHANNEL
3
7
3
2
8
2
SELECT
1
9
1
0
10
0
10
CRUNCH
FUSE
BIAS
VOLTAGE
100V
F8AL/250V
115V
GND
F5AL/250V
220/240V
F3.15AL/250V
2
4
6
4
6
4
7
3
7
3
7
3
8
2
8
2
8
2
9
1
9
1
9
1
0
10
0
10
0
RHYTHM
4
BIAS
A PRODUCT OF PEAVEY ELECTRONICS CORP.
TEST
5022 HARTLEY PEAVEY DRIVE
MERIDIAN MS. 39305, U.S.A.
EFFECTS
PREAMP
SEND
RETURN
OUT
REMOTE SWITCH
3
5
6
7
6
4
6
4
6
7
3
7
3
7
3
8
2
8
2
8
2
9
1
9
1
9
1
10
0
10
0
10
6505
SPEAKER OUTPUTS
120W RMS/44V RMS 4Ω MIN.
SPEAKER JACKS PARALLELED
CLASS 2 WIRING
Made in China
8
9
4
6
4
6
4
6
7
3
7
3
7
8
2
8
2
9
1
9
1
9
0
10
0
10
0
10
LEAD
DESIGNED AND ENGINEERED IN U.S.A.
8
Advertisement
Table of Contents
