Specifications; Operation - DeWalt DCL182 Instruction Manual

based on product components, temperature and end-
user application.
Checking State of Charge (Fig. C)
• When the LED light is ON, the charge indicator LED
will illuminate green, yellow or red indicating the percent
of charge in the battery:
- gREEn: ≥50%
YEllOW: >25% to >50%
-
- RED: ≤25%
• If less than 3%, light and indicator will flash two times
every 45 seconds until out of power.
• If the color of the charge indicator LED
not illuminate, charge the battery.

SPECIFICATIONS

Voltage
Battery type
Lumens
Articulating head LED
Light Beam Angle
Articulating head LED
Run Time When Fully Charged
Articulating head LED

OPERATION


CAUTION: Do not stare into the LEDs. Serious eye
injury could result.
Pivoting Carabiner (Fig. A, D)

CAUTION: When the LED light hangs by the pivoting
carabiner, do not shake the LED light or the object from
which it hangs. Do not hang the LED light overhead or
from any electrical wires or anything that is not secure.
Personal injury or property damage may occur.

CAUTION: Only use the pivoting carabiner for hanging
the LED light. The pivoting carabiner is not intended
to support additional weight. Do not attach or hang
anything additional to the LED light or risk of breakage
may occur.

CAUTION: Do not use the pivoting carabiner to reach
with or to support your weight in any situation. The
pivoting carabiner is not intended for fall protection.
The built in pivoting carabiner
hoses, pipes, tubes or cables in the space you are working in.
1. To access the pivoting carabiner
carabiner 4 away from the LED light housing
2. Press down the spring loaded gate
carabiner and slip the hose, pipe, tube or cable in your
4
work space into the pivoting carabiner
10 is red or does
DCL182
V 4
DC
18650 Li‑Ion
Low ‑ 250
lm Mid ‑ 500
High ‑ 1000
degrees 120
Low ‑ 12
hours Mid ‑ 8
High ‑ 3.5
can be attached to anchored
4
4 , rotate the pivoting
2 .
on the pivoting
12
.
4
3. Ensure the spring loaded gate
position and locks the pivoting carabiner
anchored anchored hose, pipe, tube or cable inside of it.
nOTE: Ensure the pivoting carabiner
10
and will not slide off or along the anchored hose, pipe,
tube or cable before proceeding.
4. To remove the pivoting carabiner
anchored hose, pipe, tube or cable, open the spring
loaded gate
and slide the anchored hose, pipe, tube or cable from
the pivoting carabiner opening.
5. Return and secure the pivoting carabiner
onto the LED light housing
Articulating Head LED (Fig. A, D, E)
The articulating head LED
1. To move the articulating head LED
pivoting carabiner
light housing
2. To adjust the beam of the articulating head LED
swivel and rotate the articulating head LED
it into the desired position.
3. You can use the pivoting carabiner
articulating head LED
Multi Function Button (Fig. A)
The articulating head LED
low, medium and high.
low battery indication. If less than 3%, the activated
LED and charge indicator LED will flash two times every 45
seconds until out of power.
1. Press the multi function button
articulating head LED
2. Press the multi function button
activate the articulating head LED
3. Press the multi function button
the articulating head LED
4. Press the multi function button
the off the LED
nOTE: If the light remains on for more than five seconds,
pressing the multi function button
turning off the light..
nOTE: With the light activated, a long press of the multi
function button
Magnets (Fig. A)

CAUTION: When the LED light hangs by the magnets,
do not shake the LED light or the object from which
it hangs. Do not hang the work LED light overhead
or from anything that is not secure. Personal injury or
property damage may occur.

CAUTION: Only use the magnets for hanging the LED
light. The magnets are not intended to support additional
weight. Do not attach or hang anything additional to the
LED light or risk of breakage may occur.
1. The DCL182 has magnets
pivoting carabiner
12 returns to it locked
4
4
, then grasp the pivoting carabiner
12
2 .
swivels from 0°–360°.
3
3 first pull the
4 upwards and away from the LED
3 .
4 to prop up the
3 on a flat surface.
3 has three brightness settings,
once to activate the
1
high setting.
3
1 a second time to
3 medium setting.
a third time to activate
1
low setting.
3
1 a fourth time to turn
5 .
1 again will result in
1 will result in turning off the light.
5 built into the bottom of the
4 .
English
4 to the
is fully secured
from the
4
4 into place
,
3
by twisting
3
5