7.1 Ch Input; Aux2 Input; Lip.sync - Marantz SR6001 User Manual

7.1 CH INPUT

The SR6001 is equipped for future expansion
through the use of Multi channel Super Audio CD
multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources
1. 2.
M-CH ST
AV SURROUND RECEIVER SR6001
7
INPUT SELECTOR
2.
CL
PURE DIRECT DISP MULTI AUTO TUNED ST SPKR A
SLEEP AUTO SURR DIRECT DISC 6.1
CH/ CAT
DSD
4.
SURROUND MULTI
MODE AUTO MULTI SPEAKER MULTI/
7.1CH INPUT
PURE DIRECT HT-EQ
STANDBY INFO
E
MENU
POWER ON/STANDBY PHONES
T.TONE
/SET UP
REC
4.
- PRESET
3.
DISC+
READY
VOLUME CH-SEL
1.
BASS
SURROUND
DIGITAL
TV TV
L C R
M LFE
SL S SR
DOWN UP
TUNER
DE MEMORY CLEAR TAPE
SPEAKERS
MultEQ A/B
AUX 1 INPUT REMOTE CONTROLLER
DIGITAL S-VIDEO VIDEO L AUDIO R
MIC
52
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH on the remote to switch
the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH-SEL button on the
remote.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –12 to +12 dB.
The subwoofer can be adjusted between –18
and +12 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the MAIN VOLUME
knob or the VOL buttons on the remote.
STEREO NIGHT P.SCAN
8 9
7.1CH IN 7.1CH IN A/D HT-EQ
To cancel the 7.1 CH. INPUT setting, press the 7.1
0 0 +10
MEMO
CH INPUT button on the front panel or press 7.1 CH
VOLUME VOLUME
SPKR A/B MUTE
on the remote.
CAT M-SPKR
Notes:
MENU
• When the 7.1 CH. Input is in use, you may not select
a surround mode, as the external decoder determines
ENTER
processing.
EXIT
• In addition, there is no signal at the record outputs
T.DISP PTY F.DIRECT
when the 7.1 CH. Input is in use.
+ - TUNING +
ANGLE SUB TITLE AUDIO
V-OFF ATT.
TREBLE
DVD DVD VCR VCR DSS DSS
CD CDR MD
AUX1 AUX2 AMP
RC5001SR

AUX2 INPUT

If you don't need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
AV SURROUND RECEIVER SR6001
INPUT SELECTOR
PURE DIRECT DISP MULTI AUTO
SLEEP AUTO SURR
DSD
SURROUND
MODE AUTO MULTI
7.1CH I
PURE DIRECT HT-EQ
STANDBY
MEN
POWER ON/STANDBY PHONES

LIP.SYNC

Depending on the image device (TV, monitor,
projector, etc.) connected to the SR6001, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR6001
to correct the time lag between the sound and image.
It can be operated with the "LIP SYNC" and 1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
Note:
• The LIP.SYSNC feature turns OFF (0 ms) in
the SOURCE/PURE DIRECT mode. When the
SOURCE/PURE DIRECT mode is deactivated, the
set value of the LIP.SYSNC feature is automatically
restored.
l/
SLEEP DISPLAY P.DIRECT SURROUND
LIP SYNC/
AUTO dts INPUT
1 2 3
BAND
CS EX/ES VIRTUAL T.MODE
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
7.1CH IN 7.1CH IN A/D HT-EQ
0 0 +10
CL MEMO
CH/ CAT VOLUME VOLUME
SPKR A/B MUTE
MULTI/ CAT M-SPKR
INFO MENU
ENTER
T.TONE
/SET UP EXIT
REC T.DISP PTY F.DIRECT