Basic Operation - Marantz SR6001 User Manual

BASIC OPERATION

NORMAL MODE
(When operating Marantz AV equipment products)
This remote control is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, MD, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifi er).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifi er on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifi er source
changes to DVD.
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2
seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote control is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
control.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote control Corresponding preset Device name
source name code
TV TV Television
DVD DVD DVD player
VCR VCR Video deck
DSS SATELLITE Satellite broadcasting
tuner equipment
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
- PRESET + - TUNING +
SOURCE SET OFF
l/
1.
SLEEP DISPLAY P.DIRECT
DISC+ ANGLE SUB TITLE AUDIO
AUTO dts
CH-SEL V-OFF ATT.
1 1 2 2 3 3
BASS TREBLE
CS EX/ES VIRTUAL
TV TV DVD DVD VCR VCR DSS DSS
4 4 5 5 6 6
1.
2.
TUNER CD CDR MD
M-CH ST STEREO NIGHT
7 7 8 8 9 9
TAPE AUX1 AUX2 AMP
7.1CH IN A/D
0 0 +10
CL
REMOTE CONTROLLER
CH/ CAT
RC5001SR
SPKR A/B MUTE
1.
Press and hold down the SOURCE button for the
appliance which should be controlled and press
SET button until the SEND indicator blinks twice.
Then back light fl ushes.
2.
Press the 4-digit code for appliance (code table
at the end of this book)
When the procedure is successful, the SEND
indicator will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SCANNING THE CODE TABLE
SOURCE SET OFF
l/
3.
LEARN SEND
SLEEP DISPLAY P.DIRECT
AUTO dts
SOURCE SOURCE SET OFF ON
1 2 3
l/ l/
2.
SLEEP DISPLAY P.DIRECT SURROUND
CS EX/ES VIRTUAL
4 5 6
LIP SYNC/
AUTO dts INPUT
1 2 3 M-CH ST STEREO NIGHT
7 8 9
CS EX/ES VIRTUAL T.MODE
3. 7.1CH IN A/D
4 5 6
0 +10
CL
CH/ CAT
DISC+ ANGLE SUB TITLE AUDIO SPKR A/B MUTE
CH-SEL V-OFF ATT.
MULTI/ CAT M-SPKR
BASS TREBLE
TV TV DVD DVD VCR VCR DSS DSS
2. INFO
5.
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
ENTER
T.TONE
/SET UP
REMOTE CONTROLLER
RC5001SR
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking
twice. Then back light fl ushes.
3.
Aim the remote control at the appliance and
slowly alternate between pressing CH+ button
and the SOURCE ON/OFF button for the
appliance.
4.
Stop when the appliance turns off.
5.
Press ENTER button once to lock in the code.
ON
CHECKING THE CODE
SURROUND
LIP SYNC/
INPUT
T.MODE
3.
LEARN SEND
P.SCAN
SOURCE SET OFF ON
HT-EQ l/
1.
SLEEP DISPLAY P.DIRECT SURROUND
MEMO
4.
VOLUME LIP SYNC/
AUTO dts INPUT
1 2 3
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
TV TV DVD DVD VCR VCR DSS DSS
1.
2.
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
RC5001SR
1.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light fl ushes.
2.
Press the INFO button.
The SEND indicator will blink twice.
3.
To view the code for fi rst digit, press 1 once.
Wait 3 seconds, count the SEND indicator
ON
blinks (e.g. 3 blinks = 3) and write down the
SURROUND
number.
LIP SYNC/
INPUT
Note:
T.MODE
If a code digit is "0", the SEND indicator will not
P.SCAN
blink.
HT-EQ
MEMO
4.
3
Repeat step three more times for remaining
VOLUME
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.
MENU
EXIT
RESETTING THE CODE
LEARN SEND
SOURCE SET OFF ON
l/
1.
SLEEP P.DIRECT SURROUND
DISPLAY
LIP SYNC/
AUTO dts INPUT
1 2 3
DISC+ ANGLE SUB TITLE AUDIO
CH-SEL V-OFF ATT.
BASS TREBLE
TV TV DVD DVD VCR VCR DSS DSS
2.
1.
TUNER CD CDR MD
TAPE AUX1 AUX2 AMP
REMOTE CONTROLLER
RC5001SR
SOURCE SET OFF ON 1.
Press and hold down the SOURCE button
l/
SLEEP DISPLAY P.DIRECT SURROUND
for appliance which should be controlled and
LIP SYNC/
AUTO dts INPUT
1 2 3 press SET button until the SEND indicator
CS EX/ES VIRTUAL T.MODE
blinking twice.
4 5 6
M-CH ST STEREO NIGHT P.SCAN
Then back light fl ushes.
7 8 9
7.1CH IN A/D HT-EQ
2.
Press the below codes to reset.
0 +10
CL MEMO
CH/ CAT VOLUME
SPKR A/B MUTE
TV : 1000
DVD : 2000
MULTI/ CAT M-SPKR
VCR : 3000
INFO MENU
DSS : 4000
ENTER
The indicator will blink twice.
T.TONE
/SET UP EXIT
Note:
After this procedure, the selected SOURCE button is
set initial code.
LEARN SEND
SOURCE SET OFF ON
l/
SLEEP P.DIRECT SURROUND
DISPLAY
LIP SYNC/
AUTO dts INPUT
1 2 3
CS EX/ES VIRTUAL T.MODE
4 5 6
M-CH ST STEREO NIGHT P.SCAN
7 8 9
7.1CH IN A/D HT-EQ
0 +10
CL MEMO
CH/ CAT VOLUME
SPKR A/B MUTE
MULTI/ CAT M-SPKR
INFO MENU
15