Related Manuals for La Crosse Technology WS-9014TWC
Summary of Contents for La Crosse Technology WS-9014TWC
- Page 1 WS-9014TWC Wireless 433 MHz Temperature Station Instruction Manual TABLE OF CONTENTS...
-
Page 2: Table Of Contents
Topic Page Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation 9-10 Setting the Time 11-12 Selecting Units of 12-13 Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Additional remote 14-17 temperature sensors (optional) Mounting 17-18 Troubleshooting 19-21 Maintenance and Care... -
Page 3: Inventory Of Contents
The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3 each, 1/2” Philips screws. One strip of double sided adhesive tape. Instruction Manual and Warranty Card. Figure 1 Figure 2 ADDITIONAL EQUIPMENT (not included) 1 Philips screwdriver. 2 Fresh AA 1.5V batteries. 2 Fresh AA 1.5V batteries. - Page 4 Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station.
- Page 5 In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above.
- Page 6 resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps below.
- Page 7 choice shown on the display press and release the “SET” button once. 2. Degree Fahrenheit will now show. To change between Fahrenheit and Celsius, press and release the “MIN/MAX” button. b. When you have your choice shown on the display press and release the “SET”...
- Page 8 hours this area will be blank. b. When the correct hour is shown, press and release the “SET” button once. 4. A minute will now be flashing. Press and release the “MIN/MAX” button until the correct minutes are displayed. Press and release the SET button once more and you are done.
-
Page 9: Detailed Setup Guide
DETAILED SETUP GUIDE BATTERY INSTALLATION REMOTE TEMPERATURE SENSOR Remove the mounting bracket. Remove battery cover Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or start-up problems may occur. Replace cover. - Page 10 INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing temperatures to register incorrectly. Remove the battery cover on the backside. To do this, push up and pull out. Observing the correct polarity, install 2 AA...
-
Page 11: Setting The Time
temperature station should now show: “-:- - ” in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s. TIME SETTING THE TIME Press and hold the “SET” button for 5 second, “12h” will appear in the TIME LCD. Press and release the “MIN/MAX”... -
Page 12: Selecting Units Of
button to set the hours Press and release the “SET” button to move to the minute setting Press and release the “MIN/MAX” button to set the minutes. Press and release the “SET” button to activate the clock. Note: When in 12h mode, there is only a “PM”... -
Page 13: Minimum And Maximum
again, “°F” will appear in the TIME LCD. Press and release the “MIN/MAX” button to shift between °F and °C. Press and release the “SET” button twice to activate settings. FEATURES MINIMUM AND MAXIMUM TEMPERATURES Press and release the “MIN/MAX” button, “MIN”... -
Page 14: Additional Remote
maximum temperatures—press and hold the “RESET/+” button for 4 seconds. C. ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS (OPTIONAL) The WS-9014U is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-9014U. - Page 15 Note: When setting up multiple units it is important to remove the batteries from all existing units in operation, then to insert batteries first into all the remote temperature sensor units, and in numeric sequence. Second, install batteries into the indoor temperature station.
- Page 16 programming and operating instructions. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS To view the temperature of a different remote temperature sensor unit, press and release the “CH” button. A shift from one “boxed” number to the next should be observed in the OUTDOOR LCD.
-
Page 17: Mounting
readings, press and hold the “MIN/MAX” button for four seconds. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North- facing wall. The sending range is 80ft; obstacles such as walls, concrete, and large metal objects will reduce the range. - Page 18 The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. To wall mount, remove the table stand. To do this, pull down on the stand from the rear and rotate forward.
-
Page 19: Troubleshooting
TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. - Page 20 Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions; so two temperature sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the temperature sensors are designed for different working...
-
Page 21: Maintenance And Care
MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. - Page 22 Transmitting 433MHz Frequency Measuring Temperatures Indoor 32°F to 156.2°F with Temperature 0.2°F resolution. Station: Indoor (0°C to 69.0°C with 0.1°C resolution) -21.8 °F to 156.2°F with Indoor Temperature 0.2°F resolution. Station: Outdoor (-29.9°C to 69.0°C with 0.1°C resolution) Temp accuracy +/- 1°F (+/- .5°C) Transmitting Maximum 80 feet (25m)
- Page 23 Temperature Station Dimensions: (L x W x H) Indoor Temperature 2.36 x 0.88 x 5.90 in. Station Remote Temperature 1.57 x 0.85 x 5.00 in. Sensor Battery life Approximately 1 year...
-
Page 24: Warranty Information
WARRANTY INFORMATION La Crosse Technology provides a 1-year warranty on this weather station. Contact La Crosse Technology immediately upon discovery of any defects covered by this warranty. Before sending the weather station in for repairs, contact La Crosse Technology. The weather station will be repaired or replaced with the same or similar model. - Page 25 This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. warranty work, technical...
- Page 26 Freq. 433.92 MHz La Crosse Technology Made in China WS-9014TWC FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1.
- Page 27 All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. This handbook may contain mistakes and printing errors. The information in this handbook is regularly checked and corrections made in the next issue.