Table of Contents
Advertisement
Features:
•
Clear functional design
•
Easy to read outdoor temperature from indoors
•
Maximum and minimum values with auto reset
•
Easy to mount
•
Weather resistant
Specifications:
Measuring range:
Resolution:
Temperature Updating Interval: Every 10 Seconds
Battery:
Inserting the Battery:
1. The battery cover is located on the back of the
thermometer.
2. Using your fingers slide the battery cover off of the battery compartment.
3. Observing the correct polarity insert one AAA battery into the battery compartment.
4. Replace the battery cover.
Setting the Time:
1. Press the MODE button to enter the setting mode.
2. The hours digits will flash in the center of the display.
3. Press and release the + button to advance the hour.
NOTE: When in the hours between midnight and noon, A.M. will be displayed on the left of the display. When in the
hours between noon and midnight P.M. will be displayed on the left side of the display.
4. Press and release the MODE button to confirm the hour and advance to the minute setting.
5. The minutes digits will flash at the bottom of the display.
6. Press and release the + button to advance the minute.
7. Holding down the + button will advance the minutes faster.
8. Press and release the MODE button to confirm the minutes and exit the time setting mode.
WT-62U Digital Window Thermometer
-22 ºF to +122 ºF
0.2 ºF
1 AAA
1
Advertisement
Table of Contents
Related Manuals for La Crosse Technology WT-62U
Summary of Contents for La Crosse Technology WT-62U
- Page 1 WT-62U Digital Window Thermometer Features: • Clear functional design • Easy to read outdoor temperature from indoors • Maximum and minimum values with auto reset • Easy to mount • Weather resistant Specifications: Measuring range: -22 ºF to +122 ºF Resolution: 0.2 ºF...
- Page 2 Clean the thermometer with a soft damp cloth only. Do not use solvents or scouring agents. • Please do not try to repair the unit. Contact the original point of purchase or La Crosse Technology Warranty for repair/ replacement instructions.
- Page 3 La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above.
- Page 4 WS-9013U Wireless 433 MHz Radio-controlled Weather Station Instruction Manual...
-
Page 5: Table Of Contents
Topic Inventory of Contents/Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Programming Sequence Function Keys 12/24 Hour Time Setting Time Zone Setting Daylight Saving Time Setting Time Setting (WWVB & Manual) Setting Day, Date and Year Selecting °F or °C Setting the LCD Contrast Features... -
Page 6: Inventory Of Contents/Additional Equipment
INVENTORY OF CONTENTS 1. The weather station (Figure 1). 2. One TX6U remote temperature sensor with mounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive tape. 5. Instruction Manual and Warranty Card. Time LCD Date LCD Indoor LCD Outdoor LCD... -
Page 7: About Wwvb
ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2, 000 miles away through the internal antenna in the weather station. -
Page 8: Quick Set-Up Guide
QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor weather station and remote temperature sensor 3 to 5 apart. 2. Batteries should be out of both units. 3. Place the batteries into the remote temperature sensor first then into the indoor weather station. -
Page 9: Detailed Set-Up Guide
DETAILED SET-UP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket. bracket snaps on and off easily. 2. Remove the battery cover, by sliding the cover down. 3. Observing the correct polarity install 2 AA batteries. tightly (to avoid start-up problems make sure they do not spring free). -
Page 10: Program Mode
PROGRAM MODE Programming Note: If 30 seconds are allowed to pass or either the IN or the OUT button is pressed during programming modes, the unit will set the last information entered—the display will stop flashing and return to normal time-date readings. If you don’t leave the program mode during the programming of sections III through VIII, you can advance to step 3 of the next program setting. -
Page 11: Function Keys
II. FUNCTION KEYS The function keys are operated by pressing the key corresponding to the operation that you want to perform. II. 12 OR 24 HOUR TIME SETTING 1. Press and hold the “SET” button for 3 seconds or until “12 h”... -
Page 12: Daylight Saving Time Setting
4. Select your appropriate time zone “CH” button. selection of the Time Zone, abbreviations for the time zones found in North America will flash across the top of the TIME LCD. Observe the chart below, corresponding abbreviations, time zones, and codes. Note: There are more time zones represented by numbers than there are represented by 3 letter abbreviations. -
Page 13: Time Setting (Wwvb & Manual)
6. Press and release the “SET” button to confirm and advance to the Time setting mode. V. TIME There are two methods by which the time can be set: A) Automatically via WWVB reception or B) Manually. A. WWVB (Remote Control Time) This method requires you to do nothing except wait for the signal to be received and to select a time zone. -
Page 14: Setting Day, Date And Year
Press and release the “SET” button to confirm the hour setting and to advance to the minute setting mode. The minute digits should be flashing. Press and release the "CH” button to change the minutes—increasing the minutes by increments of 1 with each press of the “CH” button. Press and release the “SET”... -
Page 15: Selecting °F Or °C
5. The numeric-month will be flashing in the DATE LCD. Press and release the “CH” button to select to the current month. 6. Press and release the “SET” button to confirm the numeric- month, and to enter the numeric-day setting mode. 7. -
Page 16: Setting The Lcd Contrast
VIII. SETTING THE LCD CONTRAST 1. Press and hold the “SET” button for 3 seconds or until “12h” or “24h” flashes in the DATE LCD. 2. Press and release the “SET” button 10 more times to reach the LCD contrast setting mode. 3. -
Page 17: Indoor Temperature
FEATURES OF THE WS-9013U WWVB Tower Icon (indicates time reception) Remote Temperature Sensor Channel Indicator I. INDOOR TEMPERATURE The current indoor is displayed in the INDOOR LCD and is updated every 10 seconds. II. OUTDOOR TEMPERATURE The outdoor temperature is viewed in the OUTDOOR LCD. The outdoor temperature is updated every five minutes. -
Page 18: Minimum & Maximum Records
III. MINIMUM AND MAXIMUM TEMPERATURE RECORDS The WS-9013U keeps a record of the MINIMUM and MAXIMUM temperature and the time and date of their occurrence—for both the indoor and outdoor modes. A. VIEWING THE INDOOR TEMPERATURE RECORDS 1. Press the “IN” button once. “MIN” appears in the upper portion of the flashing INDOOR LCD indicating that the minimum temperature and the time and date of occurrence are displayed. -
Page 19: Units (Set-Up, Viewing & Operation)
WS-9013U. These extra remote temperature sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly. A TX6U will monitor temperature only, a TX3U will monitor... - Page 20 3. Place all remote temperature sensor units in a numeric sequential order. 4. In sequential order, install batteries (follow the same battery installation procedures seen in section I. A) of the Detailed Set-Up Guide). 5. Install batteries into the indoor weather station. 6.
-
Page 21: Mounting
MOUNTING Note: Before permanently mounting ensure that the indoor weather station is able to receive WWVB signals from the desired location. Also, extreme and sudden changes in temperature will decrease the accuracy of the indoor weather station. To achieve a true temperature reading, avoid mounting where direct sunlight can reach the remote temperature sensor. - Page 22 ensure a secure hold. The mounting surface should be smooth and flat. 2) Remove the protective strip from one side of the tape. Adhere the tape to the designated area on the back of the mounting bracket. 3) Remove the protective strip from the other side of the tape.
-
Page 23: Troubleshooting
3) Remove batteries for five minutes, reinsert and leave the unit alone overnight without pressing buttons. 4) If there are still problems, contact La Crosse Technology. Problem: Hour is incorrect (minute and date are correct). Solution: Be sure correct time zone and daylight saving time is selected. -
Page 24: Specifications
• Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology for repairs. SPECIFICATIONS Temperature measuring range: Indoor: Outdoor: Indoor temperature checking interval: Outdoor temperature checking interval: (Remote Temperature Sensor) Outdoor temperature reception:... -
Page 25: Warranty Information
La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. - Page 26 State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or information contact: La Crosse Technology 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610...