Suggested Spare Parts ........... 33 Labels Asssembly ..........80-81 Terms and Conditions of Sale - Parts ....82 Specification and part number NOTE are subject to change without notice PAGE 4 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Safety Message Alert Symbols. NOTE be damaged if you do not follow instructions. PAGE 8 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
■ NEVER! place hands inside the drum while the drum is the equipment and/or injury to user may result. rotating. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications. MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 9...
Page 9
■ High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can cause serious burns. PAGE 10 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Machine Safety Decals The Multiquip MC-42S mixer is equipped with a number of safety decals (Figure 1A). These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine.
Page 11
Honda Engine Owner's manual furnished with the in Table 6. Remember distance affects the wire size of the engine. extension cable. ) . s , s t . c t PAGE 12 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Tow Bar — This mixer uses various towing bars, please reference the frame assembly drawing and parts list in this manual to determine which tow bar meets your requirements. MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 13...
10. Fuel Tank – Holds unleaded gasoline. For additional information refer to engine owner's manual. PAGE 14 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
The Multiquip MC-42S concrete mixer is shipped with the handwheel detached. Attach the handwheel to the mixer as shown in Figure 4. Figure 4. Handwheel Assembly MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 15...
(gasoline models only). 3. As a minimum, use a 1/2-inch bolt and nylock nut grade 5 when securing either tow bar to the towing vehicle, PAGE 16 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
1/2-inch bolt through tow bar and frame. Secure tow bar to frame with 1/2-inch nylock nut. Tighten to 40 ft.-lbs. Figure 5. Tow Bar and Safety Chain Installation MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 17...
"OFF" position and correct the problem, press the reset switch button, and turn the main switch to the "ON" position. PAGE 18 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Page 18
MC-42S CONCRETE MIXER — ELECTRIC MOTOR Figure 6. Single Phase Electric Motor with 12 inch Pigtail Cable MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 19...
Page 19
Check the zerk grease fittings (Figure 27) as shown in the maintenance section of this manual. These grease fittings lubricate the handwheel and the yoke mechanism . Figure 8. Engine Oil Dipstick (Oil Level) PAGE 20 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Page 20
Move the throttle lever (Figure 11) away from the slow position, about 1/3 of the way toward the fast position. Figure 14. Starter Grip Figure 11. Throttle Lever MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 21...
NOTE extension cord so that it lays flat and is not curled underneath the mixer. Figure 17. Electric Motor ON/OFF Switch (ON Position) PAGE 22 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
(OFF Position) Disconnect the electric motor's extension cord from its power source. Figure 19. Filling Mixing Drum Clean drum of all debris and foreign matter. MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 23...
Page 23
) 3 ( a i c i t a r e t t n i r e t . s l PAGE 24 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
For thorough mix and longer drum life, always wash drum out after each use. NEVER! pour or spray water over the engine or electric Figure 27. Grease Fittings Electric Motor motor. PAGE 26 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Page 26
CAUTION: ALWAYS wear safety glasses NOTE when removing or installing force fitted parts. Failure to comply may result in serious injury. Figure 29. Suspension Components MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 27...
Page 27
Cover the mixer and place it a clean dry area, that is protected from harsh elements. Figure 30. Wheel Lug Nuts Tightening Sequence PAGE 28 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Page 28
NOTE PAGE MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 29...
>, belong to the same assembly or kit. If more than one of the same NOTE reference number is listed, the last one listed indicates newest (or latest) part available. PAGE 32 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
1 ..28462ZH8003 ..ROPE, RECOIL STARTER Part numbers on this Suggested Spare Parts List may supercede/ NOTE replace the P/N's shown in the test pages of this manual. MC-42S CONCRETE MIXER — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17) — PAGE 33...
Page 35
PART OF FRAME PART OF YOKE NOTES: MIXING BLADES ARE PART OF DRUM ASSEMBLY. TO RE-ORDER NEW BLADES A COMPLETE MIXING DRUM MUST BE PURCHASED. PAGE 36 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)
Page 46
MC-42S — ELECTRIC MOTOR MOUNTING PLATE ASSEMBLY ELECTRIC MOTOR MOUNTING PLATE ASSY. PAGE 46 — MC-42S CONCRETE MIXERS — OPERATION AND PARTS MANUAL — REV. #9 (03/07/17)