Related Manuals for MULTIQUIP MC3SE
Summary of Contents for MULTIQUIP MC3SE
- Page 1 PARTS AND OPERATION MANUAL MIX N' GO MINI CONCRETE MIXER STEEL DRUM MODELS MC3SE, MC3S (B&S) PLASTIC DRUM MODELS MC3PE, MC3P (B&S) Revision #0 (02/26/03)
- Page 2 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...
-
Page 4: Table Of Contents
TABLE OF CONTENTS Here's How To Get Help ..........3 Table Of Contents ............. 4 Parts Ordering Procedures ........5 Multiquip Mix N' Go — Portable Concrete Mixer Safety Message Alert Symbols ......6-7 Rules For Safe Operation ........8-10 Operation and Safety Decals ...... -
Page 5: Safety Message Alert Symbols
NOTE injury. Multiquip Model MC-3 Portable Concrete Mixer. Before using this mixer, ensure Accidental Starting that the operating individual has read and understands all instructions in this manual. - Page 6 MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position, and remove the ignition key ALWAYS wear approved respiratory when the machine is not in use. protection. Equipment Damage Messages Sight and Hearing hazard Other important messages are provided throughout this manual...
-
Page 7: Rules For Safe Operation
■ Refer to the Engine Owner's Manual for engine technical questions or information. ■ NEVER use accessories or attachments, which are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result. ■ Manufacturer does not assume responsibility for any accident due to equipment modifications. - Page 8 RULES FOR SAFE OPERATION ■ NEVER Run engine without air cleaner. Severe engine ■ High Temperatures – Always stop engine and allow the damage may occur. engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can ■...
- Page 9 RULES FOR SAFE OPERATION Emergencies ■ ALWAYS know the location of the nearest fire extinguisher . ■ ALWAYS know the location of the nearest first aid kit . ■ In emergencies always know the location of the nearest phone or keep a phone on the job site . Also know the phone numbers of the nearest ambulance , doctor and fire department .
-
Page 10: Operation And Safety Decals
OPERATION AND SAFETY DECALS Machine Safety Decals The Mix N' Go mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. - Page 11 OPERATION AND SAFETY DECALS WARNING! ADVERTENCIA! AVERTISSEMENT! 1. Read owner’s manual before operating mixer. 1. Lea el manual de operació antes de usar la mezcladora. 1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur. 2. Keep unauthorized and untrained people away 2.
-
Page 12: Specifications
MIX N' GO MIXER — SPECIFICATIONS c i f i t a & c i r & r t s t r e a c i v l a i l y c i r r o t . n i o r t p s i . -
Page 13: Dimensions (Mixer)
MIX N' GO MIXER — DIMENSIONS (MIXER) Figure 1. Mix N' Go Mixer Dimensions PAGE 14 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) -
Page 14: Dimensions (Electric Motor)
MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR) Figure 2. Electric Motor MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) — PAGE 15... -
Page 15: General Information
MIX N' GO MIXER — GENERAL INFORMATION PORTABLE GENERATORS APPLICATION This mixer is only intended for the production of concrete When using a portable generator it must have a minimum and mortar . The mixer must be used for its intended output of 2.5 kw and be continuous rated. -
Page 16: Mixer Components
MIX N' GO MIXER — MIXER COMPONENTS Figure 4 shows the basic components of the Mix N' Go Mixer . Figure 4. Mixer Components ) . s i d r o i t r e t g i t , s r s t i . -
Page 17: Basic Engine
MIX N' GO MIXER — BASIC ENGINE Figure 5. Engine Controls and Components INITIAL SERVICING Throttle Lever – Used to adjust engine RPM speed (lever The engine (Figure 5) must be checked for proper lubrication and advanced forward SLOW , lever back toward operator filled with fuel prior to operation. -
Page 18: Assembly Instructions
MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS Assembly 1. Remove the mixer drum and associated components from the packing container (Figure 6). Match the components against the parts list to make sure that they are all accounted for. Figure 6. Packing Container Figure 8. - Page 19 MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS 6. Tip mixer onto mouth as shown in Figure 10, and insert 9. Before attempting to lift mixer, locate the frame locking clip. support stand into frame swivel point. Attach the locking clip as shown in Figure 12. This will prevent the mixing drum from moving when the mixer is positioned in an upright position.
-
Page 20: Pre-Inspection (Gasoline Engine)
MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE) CAUTION CAUTION CAUTION CAUTION CAUTION 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. NEVER operate the mixer in a confined area or enclosed 4. - Page 21 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...
-
Page 22: Initial Start-Up (Electric Motor)
MIX N' GO MIXER — INITIAL START-UP (ELECTRIC MOTOR) 5. Plug the other end of the extension cord into a 120 VAC Initial Start-up Instructions (Electric Motor) G.F.C.I. protected receptacle. Remember the power require- Starting ments for this electric motor is 120 VAC, 60 Hz. The use of CAUTION: CAUTION: CAUTION:... -
Page 23: Initial Start-Up (Gasoline Engine)
MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE) 4. Grasp the starter grip (Figure 23) and slowly pull it out. The DO NOT attempt to operate the mixer until resistance becomes the hardest at a certain position, corre- the Safety, General Information and sponding to the compression point. - Page 24 MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE) Stopping The Engine Normal Shutdown 1. Move the throttle lever to the "TURTLE" (IDLE) position (Figure 26) and run the engine for three minutes at low speed. Figure 26. Throttle Lever (Idle Position) 2.
-
Page 25: Maintenance
MIX N' GO MIXER — MAINTENANCE Maintenance 5. Insert oil filler plug and tighten. Gearbox Oil Check 1. Position the mixer on a level surface and place a support block under the front of the mixer frame as shown in Figure 29. This will level the mixer. - Page 26 MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE) t n i ) 3 ( e n i l i O r i A ) 1 ( g i t s t u & s t l g u l l o o g n i s n i r r A...
- Page 27 MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE) DANGER : Maintenance Perform the scheduled maintenance procedures as definded by DO NOT use gasoline as a cleaning solvent, Table 6 and below: because that would create a risk of fire or DAILY explosion.
-
Page 28: Preparation For Long-Term Storage
MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE Mixer Storage For storage of the mixer for over 30 days, the following is recommended: Drain the fuel tank completely, or add STA-BIL to the fuel. Run the engine until the fuel is completely consumed. Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. - Page 29 NOTE PAGE MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) — PAGE 29...
-
Page 30: Troubleshooting (Engine)
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE) c i f t l u i t i n i r b i t i n i s o o i t i c a l o i t i l i a l i w . -
Page 31: Troubleshooting (Engine/Mixer)
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE/MIXER) n i t i t a f s i e r r v e l . r e i r p v i t o i t o i t u l f l f l r r e i t a... -
Page 32: Explanation Of Code In Remarks Column
MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts The contents of this parts book. catalog are subject to change NOTE without notice . Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. -
Page 33: Suggested Spare Parts
MIX N' GO MIXER — SUGGESTED SPARE PARTS MIX N' GO MIXER 1 TO 3 UNITS 1 to 3 Units Qty. Description 2 .... DM1840 ....V-BELT, A23 (ELECTRIC MOTOR) 2 .... MS-01 ....V-BELT, A24 (GASOLINE) MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) — PAGE 33... -
Page 34: Nameplate And Decals
MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS PAGE 34 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) - Page 35 MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS NAMEPLATE AND DECALS. PART NO PART NAME QTY. REMARKS DCL251 DECAL: WARNING MQ 510165 DECAL: MQ MIX N GO DECAL: NAMEPLATE ....... 1 .... CONTACT DISCOUNT-EQUIPMENT DCL250 DECAL: WARNING MAINTENANCE SEE DECAL ILLUSTRATIONS ON PAGES 11 AND 12.
- Page 36 MIX N' GO MIXER — MIXER ASSY. (STEEL DRUM) MIXER ASSY. (STEEL DRUM) PAGE 36 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03)
- Page 37 MIX N' GO MIXER — MIXER ASSY. (STEEL DRUM) MIXER ASSY. (STEEL DRUM) PART NO. PART NAME QTY. REMARKS DM3150 HEX HEAD BOLT M12 x 70 DM1356 OIL FILLER PLUG M14 x 2 x 15L DM1912 HEX NUT M10 DM355 HEX HEAD BOLT M8 x P1.25 x 24L DM3151 FLAT WASHER M12...
- Page 38 MIX N' GO MIXER — MIXER ASSY. (PLASTIC DRUM) MIXER ASSY. (PLASTIC DRUM) PAGE 38 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03)
- Page 39 MIX N' GO MIXER — MIXER ASSY. (PLASTIC DRUM) MIXER ASSY. (PLASTIC DRUM) PART NO. PART NAME QTY. REMARKS DM3150 HEX HEAD BOLT M12 x 70 DM1356 OIL FILLER PLUG M14 x 2 x 15L DM1912 HEX NUT M10 DM355 HEX HEAD BOLT M8 x P1.25 x 24L DM3151 FLAT WASHER M12...
- Page 40 NOTE PAGE MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #3 (02/24/03) — PAGE 41...
- Page 41 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto,...