The Input Select Menu - Sony VPL-S800U Operating Instructions Manual

The INPUT SELECT Menu

The INPUT SELECT menu is used for selecting the
input signal.
V I D E O : V I D E O
INPUT
SELECT
I N P U T - A
I N P U T - B
PICTURE
CTRL S W I T C H E R : S W ' E R 1 - 1
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER
INPUT
INFO
Operation
Use the V or the v key on the control panel to select
the input, then press the ENTER key.
On the Remote Commander, move the joy stick up or
down to select the input, press the ENTER key.
VIDEO
Selects the video signal input from the VIDEO or S
VIDEO connectors and the audio signal input from the
AUDIO IN L/R jacks.
V I D E O
V I D E O : V I D E O
INPUT
SELECT I N P U T - A
I N P U T - B
PICTURE
CTRL
S W I T C H E R : S W ' E R 1 - 1
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
Press the b or the ENTER key so that the following
pop-up menu appears.
V I D E O
V I D E O : V I D E O
INPUT
SELECT
I N P U T - S - V I D E O
I N P U T - B
PICTURE
CTRL S W I T C H E R : S W ' E R 1 - 1
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
Use the V or the v key on the control panel to select
the input, then press the B or the ENTER key.
On the Remote Commander, move the joy stick up or
down to select the input, then move the joy stick to the
left, or press the ENTER key.
If you select S-VIDEO when you have video
equipment connected to both the Y IN/C IN and IN
connectors, the signals from the Y IN/C IN connectors
are selected.
V I D E O
RESET: RESET
EXIT: MENU
INPUT-A
Selects audio and video signals input from the INPUT
A connectors.
I N P U T - A
V I D E O : V I D E O
INPUT
SELECT I N P U T - A
I N P U T - B
PICTURE
CTRL S W I T C H E R : S W ' E R 1 - 1
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
INPUT-B
Selects the signal input from the connectors on the
optional interface board (other than IFB-40) which is
installed in the INPUT B section.
I N P U T - B
V I D E O : V I D E O
INPUT
SELECT I N P U T - A
I N P U T - B
PICTURE
CTRL
S W I T C H E R
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
Note
This item is only available when the optional interface
board other than IFB-40 is installed.
SWITCHER
Selects the signal from equipment connected to the
optional signal interface switcher.
S W ' E R 1 - 1
V I D E O : V I D E O
INPUT
SELECT
I N P U T - A
I N P U T - B
PICTURE
CTRL S W I T C H E R : S W ' E R 1 - 1
INPUT
SETTING
SET
SETTING
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
Press the b or the ENTER key so that the following
pop-up menu appears.
S W ' E R 1 - 1
V I D E O : V I D S W ' E R 1 - 1
INPUT
SELECT I N P U T - A S W ' E R 1 - 2
I N P U T - B S W ' E R 1 - 3
PICTURE
CTRL S W I T C H E R : S W ' E R 1 - 4
S W ' E R 1 - 5
INPUT
SETTING
S W ' E R 1 - 6
S W ' E R 1 - 7
SET
SETTING S W ' E R 1 - 8
SEL: SET: ENTER RESET: RESET
INPUT
INFO
EXIT: MENU
Use the V or the v key on the control panel to select
the input, then press the B or the ENTER key.
On the Remote Commander, move the joy stick up or
down to select the input, then move the joy stick to the
left, or press the ENTER key.
23
(EN)