Advertisement
LIST OF CONTENTS
COTTAGE COLORS COLLECTION
TOP BUNK BED BOX (28-705) FIG.1
A.- (1) TOP BUNK BED
HARDWARE PACK (HPK00123-0)
B.- (2) 4"METAL DOWEL PINS
6 DRAWER LOFT DRESSER BOX (28-207) OR
C.- (1) LOFT DRESSER
LOFT DESK BOX (28-603) FIG.2
D.- (1) LOFT DESK
LOFT HUTCH BOX (28-766) FIG.3
E.- (1) LOFT HUTCH
HARDWARE PACK (HPK00012-0)
B.- (2) 4"METAL DOWEL PINS
6 PIECE RAILS BOX (28-730) FIG.4
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
HARDWARE PACK (HPK00104-0)
H.- (24) 80MM FLAT HEAD BOLTS
I.- (24) 5/16"-18 X 5/8" CROSS DOWEL NUTS BLACK
J.- (1) 5MM ALLEN WRENCH
FULL BOTTOM HDBD&FTBD BOX (28-709) FIG.5
T.- (1) HEADBOARD
U.- (1) FOOTBOARD
HARDWARE PACK (HPK00127-0)
V.- (4) CASTER SOCKETS
LADDER BOX (28-720) FIG.6
N.- (1) LADDER
HARDWARE PACK (HPK00008-0)
O.- (2) METAL HOOK BRACKETS
P.- (6) 1" SCREWS
TWIN/FULL SLATS BOX (100-645,100-646) FIG.7
Q.- (4) 39", 54" SLATS
HARDWARE PACK (HPK00016-0)
R.- (8) 1 1/4" SCREWS
1 PC BUNK BED END TWIN BOX (28-706) FIG.8
S.- (1) 1 PC BUNK BED END TWIN
OR LOFT DESK, TAKE THE LOFT HUTCH (E), &PLACE IT ON TOP OF LOFT DRESSER&LOFT DESK ALIGNING THE METAL DOWEL PIN WITH EACH PRE - DRILLED HOLE IN EVERY
END OF LOFT HUTCH UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLE OF THE LOFT HUTCH, REPEAT THE SAME PROCESS WITH TOP BUNK BED (A),
4.- INSERT 2 CROSS DOWEL NUTS (I) IN ACCESS HOLE INSIDE THE SIDE RAIL&GUARD RAIL,ALIGN CROSS DOWEL NUT,MAKE SURE THE GROOVE IS HORIZONTAL,
5.- ATTACH TWO SIDE RAILS &TWO GUARDRAILS TO DRESSER/HUTCH/TOP BUNK BED ASSEMBLY& 1 PC BUNK BED END TWIN (S), INSERTING TWO FLAT BOLST (H) INTO TOP
BUNK BED&1 PC BUNK BED END TWIN HOLES,USE ALLEN WRENCH TO TIGHTEN BOLTS, (DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER) ,
5.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH ENDS,PUSH THE SLAT AGAINST THE BED END POST (FIG.A) &TWO SLATS IN THE MIDDLE AT EQUAL
DISTANCE FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH TWO 1 1/4" SCREWS (S), SEE FIG.12
YES,
HORIZONTAL GROOVE
NO
FIG.9
REV 02 04/02/2019
CANYON FURNITURE COMPANY
TOP BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 2
FIG.11
FIG.10
HARDWARE PACK
HPK00123-0
A
B
FIG.1
FIG.3
B
E
HARDWARE PACK
HPK00012-0
HARDWARE PACK
HPK00008-0
O
N
FIG.6
S
FIG.8
FRONT FACE OF DESK OUTWARDS).
3.- INSERT TWO DOWEL PINS (B ) ON TOP IN EACH OUTSIDE CORNER OF LOFT DRESSER
FIG.12
PAGE 3 OF 5
C
FIG.2
F
H
FIG.4
HARDWARE PACK
HPK00127-0
U
P
FIG.5
R
FIG.7
HARDWARE PACK
HPK00016-0
1.- ASSEMBLE TOP BUNK BED,USING ONE TOP BUNK BED
END (A), ONE LOFT DRESSER (C),OR ONE LOFT DESK (D),
2 LOFT HUTCH (E) 2 SIDE RAILS (F),&2 GUARDRAILS (G).
2.- TAKE LOFT DRESSER (C ) & LOFT DESK (D ),& PLACED
THEM IN DESIRED POSITION IN THE ROOM,
FIG.A
D
HARDWARE PACK
HPK00104-0
G
I
J
T
V
Q
( PLACE
(FIG.9)
(FIG.10)
FIG.11
KIS01179-0
Advertisement
