Advertisement
LIST OF CONTENTS
COTTAGE COLORS COLLECTION
TOP BUNK BED BOX (28-705) FIG.1 (2PCS)
A.- (1) TOP BUNK BED
HARDWARE PACK (HPK00123-0)
B.- (2) 4"METAL DOWEL PINS
6 DRAWER LOFT DRESSER BOX (28-207) FIG.2
C.- (1) LOFT DRESSER
LOFT DESK BOX (28-603) FIG.3
D.- (1) LOFT DESK
LOFT HUTCH BOX (28-766) FIG.4 (2PCS)
E.- (1) LOFT HUTCH
HARDWARE PACK (HPK00012-0)
B.- (2) 4"METAL DOWEL PINS
6 PIECE RAILS BOX (28-730) FIG.5
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
HARDWARE PACK (HPK00104-0)
H.- (24) 80MM FLAT HEAD BOLTS
I.- (24) 5/16"-18 X 5/8" CROSS DOWEL NUTS BLACK
J.- (1) 5MM ALLEN WRENCH
TWIN BOTTOM HDBD&FTBD BOX (28-707) FIG.6
K.- (1) HEADBOARD
L.- (1) FOOTBOARD
HARDWARE PACK (HPK00127-0)
M.- (4) CASTER SOCKETS
LADDER BOX (28-720) FIG.7
N.- (1) LADDER
HARDWARE PACK (HPK00008-0)
O.- (2) METAL HOOK BRACKETS
P.- (6) 1" SCREWS
1.- ASSEMBLE TOP BUNK BED, USING TWO TOP BUNK BEDS (A),ONE LOFT DRESSER (C),ONE LOFT DESK (D),TWO LOFT HUTCH (E) TWO SIDE RAILS (F),&TWO GUARDRAILS (G)
2.- TAKE LOFT DRESSER (C) AND LOFT DESK (D), THEN PLACED THEM IN DESIRED POSITION IN THE ROOM, (PLACE FRONT FACE OF DESK OUTWARDS).
3.- INSERT TWO METAL DOWEL PINS (B) ON TOP IN EACH OUTSIDE CORNER OF LOFT DRESSER&LOFT DESK, TAKE THE LOFT HUTCH (E),&PLACE IT ON TOP OF LOFT DRESSER
& LOFT DESK ALIGNING THE METAL DOWEL PIN WITH EACH PRE - DRILLED HOLE IN EVERY END OF THE LOFT HUTCH UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE
HOLE OF THE LOFT HUTCH, REPEAT THE SAME PROCESS WITH TOP BUNK BED (A), SEE FIG.9
4.-INSERT 2 CROSS DOWEL NUTS (I) IN ACCESS HOLE INSIDE THE SIDE RAIL&GUARDRAIL,ALIGN THE CROSS DOWEL NUT,MAKE SURE THE GROOVE IS HORIZONTAL,
5.- ATTACH TWO SIDE RAILS & TWO GUARD RAILS TO LOFT DRESSER/HUTCH/TOP BUNK BED ASSEMBLY&LOFT DESK/HUTCH/TOP BUNK BED ASSEMBLY, INSERTING TWO FLAT
HEAD BOLST (H) INTO TOP BUNK BED HOLES, USE THE 5MM ALLEN WRENCH (J) TO TIGHTEN BOTH BOLTS,
ARE CONNECTED TOGETHER)
6.- PLACE FOUR SLATS (Q) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH ENDS,PUSH THE SLAT AGAINST THE BED END POST (FIG.A) &TWO SLATS IN THE MIDDLE AT EQUAL
DISTANCE FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH TWO 1 1/4" SCREWS (R), SEE FIG.12
HORIZONTAL GROOVE
FIG.9
NO
REV 02 04/02/2019
CANYON FURNITURE COMPANY
TOP BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 1
SEE FIG.11, REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
YES,
FIG.10
HARDWARE PACK
HPK00123-0
A
FIG.1
FIG.4
E
HARDWARE PACK
HPK00012-0
HARDWARE PACK
HPK00008-0
N
FIG.7
Q.- (4) 39'' SLATS
R.- (8) 1 1/4" SCREWS
(DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES
FIG.11
FIG.A
PAGE 2 OF 5
C
3 DRAWER NIGHT STAND BOX ( 90-503 )
K.- (1) 3 DRAWER NIGHT STAND
DESK TOP BOX ( 90-602 )
L.- (1) DESK TOP
CASTER TWIN BED BOX ( 90-707,90-709 )
FIG.2
B
M.- (1) CASTER BED HEADBOARD
N.- (1) CASTER BED FOOTBOARD
O.- (4) METAL CASTER SOCKET
F
B
J.- (6) 1 1/4" SCREW
H
FIG.5
L
M
FIG.6
O
R
FIG.8
P
HARDWARE PACK
HPK00016-0
TWIN SLATS BOX (100-645) FIG.8 (2 BOXES)
HARDWARE PACK (HPK00016-0)
D
FIG.3
HARDWARE PACK
HPK00104-0
G
I
J
K
HARDWARE PACK
HPK00127-0
Q
SEE FIG.10
FIG.12
KIS01179-0
Advertisement
