Table of Contents
Advertisement
Names and Operations of Parts
Camera Body
Body Surface
View when the dome cover is removed.
1
2
L
H
IRIS
LEVEL
3
Camera Head
1
For adjusting the angle of the camera,
such as during focusing, etc.
(
page 13)
2
[IRIS LEVEL] sensitivity adjustment
knob
For adjusting the iris level of the lens.
By turning this knob, the brightness of
video signals can be adjusted.
Turning direction of level
To darken image Counterclockwise (L side)
To brighten image Clockwise (H side)
MEMO
•
Since this unit is mounted with a
s m o k e c o v e r a s s t a n d a r d
specification, the video may appear
darker than the video during iris-level
adjustment. To improve, adjust the
iris level to a brighter setting or use
the optional clear cover.
E-6
4
5
6
FOCUS ADJ.
7
OFF
ON
OFF
ON-AGC
8
FOCUS ADJ.
OFF
ON-BLC
OFF
ON
OFF
ON-AGC
AUTO
MANU
OFF
ON-BLC
AUTO
MANU
9
LL
INT
LL
INT
PHASE
WHT.BAL.
PHASE
WHT.BAL.
R
B
10
R
B
11
SPOT
RESET
CORRECTION
FOR
SERVICE
MONITOR
12
SPOT
RESET
CORRECTION
13
When turning the level (sensitivity
•
adjustment) too far to the L side, the
sensitivity will increase by the AGC
of the camera and the picture quality
will become rough. For this reason,
always set the AGC switch to "OFF"
when making LEVEL adjustments.
3
MONITOR terminal (RCA pin)
For connecting a monitor when determin-
ing camera angle, etc. (High impedance)
4
Horizontal LOCK screw
When adjusting the camera angles horizontal
rotation, this screw is loosened for adjustment
and tightened to maintain the angle.
[FOCUS ADJ. - ON/OFF] focus
5
adjustment switch
When adjusting the focus during
installation, setting this switch to "ON" will
open the iris.
The subject depth will become closer for
easier focusing.
After focusing, set this switch to "OFF".
(Default setting: OFF)
6
[AGC - ON/OFF] Auto-gain control switch
When the brightness of the subject is not
sufficient, setting this switch to "ON" will
automatically increase the sensitivity.
(Default setting: ON)
7
[BLC - ON/OFF] Backlight
compensation switch
When the subject is under backlight, setting
this switch to "ON" will open the iris and
the subject will become easier to view.
(Default setting: OFF)
8
[AUTO/MANU] Auto/manual selection
switch
For selecting whether to adjust the white
balance automatically or manually.
(Default setting: AUTO)
9
[INT/LL] Synchronization system
selection switch
This switch sets the synchronizing
system for the camera.
INT:
This is set for internal synchronization
LL (Line Lock):
The camera's vertical synchronization is
locked to the AC 24 V power line fre-
quency.
When switching between multiple cam-
eras using a switcher, selecting this mode
and adjusting the vertical phase can re-
duce the monitor sync disturbances oc-
cur that when the camera image is
switched.
(Default setting: INT)
[WHT.BAL/PHASE] adjustment
10
selection switch
Switch to select the function of the
[R/B. +/-] adjustment button.
When setting to WHT.BAL:
When the
8
[AUTO/MANU] switch is
set to MANU, the white balance can
be adjusted using the [R/B, +/-] button.
When setting to PHASE:
When the
9
[INT/LL] switch is set to
LL, the vertical phase of the line lock
can be adjusted using the [R/B, +/-]
button.
(Default setting: WHT.BAL)
11
[R/B, +/-] adjustment button
This button is pressed when manually
adjusting the white balance or when
adjusting the vertical phase of the line
lock.
The function of this button is selected
using the
10
[WHT.BAL/PHASE] switch.
When manually adjusting the white
balance:
Press the R button to increase the red
tint and decrease the blue tint.
Press the B button to increase the blue
tint and decrease the red tint.
When adjusting the phase:
Press the + or - button to adjust the
phase.
12
[RESET] Reset button
When this button is pressed, the value
of the white balance or phase adjusted
manually is reset to the default value.
When the
10
[WHT.BAL/PHASE] switch
is set to WHT.BAL, the white balance is
reset to the default value. When the
switch is set to PHASE, the phase is
reset to the default value.
13
[SPOT CORRECTION] White-spot
correction button
11
When this button is pressed, white spots
are corrected.
(
page 15)
E-7
Advertisement
Table of Contents
