To Use The Remote Control Unit For Tv Operation; To Control The Volume Of A Jvc's Amplifier Or Receiver - JVC XV-N5SL Instructions Manual

Getting started
To use the remote control unit for TV
operation
You can operate your TV from the remote control unit.
Setting the remote control signal for
operating your TV
OPEN/
CLOSE
TV STANDBY/ON
TV1 TV2
1
TV4 TV5
4
TV7 TV8
7
TV-/-- TV0
10
RETURN SUBTITLE
CH
+
VOL-
ENTER
ENTER
CH
-
PREVIOUS
CLEAR SELECT
SLOW-
REPEAT SUB TITLE
DIGEST ANGLE
3D
PHONIC
1
Set the TV - DVD switch to "TV."
2
Hold down TV/VIDEO - CANCEL until step 4 is
finished.
3
Enter the manufacturer code of your TV listed below
by using the numeric buttons (0 to 9).
Example:
To enter the manufacturer code "01": Press "0" then
"1."
• When you purchased the unit, the manufacturer code is set
" "
to JVC (01).
4
Press ENTER.
Manufacturer code list
Manufacturer No.
AIWA 36
BEIJING 22
CCE 02
CHANGHONG 34
DAEWOO 17, 37
FERGUSON 27
FINLUX 30
FUNAI 32
GRADIENTE 15, 20
GRUNDIG 19
HITACHI 10
ITT 28
JINXING 38
JVC 01, 23,
24, 25
KONKA 40
LG (GOLDSTAR) 18
MAGNAVOX 02
MITSUBISHI 03
12
TV - DVD switch
TV DVD
STANDBY/ON
TV DVD
TV3
2 3
TV6
5 6
Numeric buttons
TV9
8 9
MUTING
0 +10
TITLE/ TV/VIDEO
GROUP CANCEL
TV/VIDEO -
CANCEL
VOL+
NEXT
STROBE
SLOW+
AUDIO VFP
PROGRESSSIVE
SCAN
ZOOM
AMP VOL
Manufacturer No.
MIVAR 29
NEC 20
NOBLEX 22
NOKIA 31
PANASONIC 04, 11
PEONY 34, 38, 39
PHILCO 10, 17, 21
PHILIPS 02
RCA 05
SAMSUNG 12, 33, 34,
35
SANYO 13, 16
SEARS 13
SHARP 06
SONY 07
TCL 41
THOMSON 26
TOSHIBA 08,14
ZENITH 09
5
Release TV/VIDEO - CANCEL.
6
Try to operate the TV by pressing
TV STANDBY/ON .
If your TV turns on or off, you have successfully set
the control signal.
The following buttons can be used for operating the
TV.
To use 5/∞ (CH+, CH–), 2/3(VOL–, VOL+), TV/VIDEO -
CANCEL and numeric buttons for TV control, set the
TV - DVD switch to "TV."
TV DVD
Turns the TV on or off.
TV
Switches the TV input mode between TV
TV/VIDEO
and VIDEO.
CANCEL
Selects the TV channels directly.
* For some TVs, pressing "+10" functions as
TV1 TV-/--
~
the "100+," while "10" functions as the
1 10
ENTER button if your TV requires pressing
TV0
0
the ENTER button after selecting a
channel number.
Mutes the TV sound.
MUTING
+10
Changes the TV channels.
CH
+
CH
-
Adjusts the TV volume.
VOL- VOL+
NOTE
• If there is more than one code listed for the
manufacturer of your TV, try them one by one until you
succeed.
To control the volume of a JVC's
amplifier or receiver
You can control the volume of a JVC's amplifier or
receiver by using the AMP VOL +/– buttons on the
remote control unit.
AMP VOL
Pressing the + button raises the audio volume of the
amplifier or receiver, while pressing the – button lowers
the volume.