H2Tu-R Ds1 Alarm History Screen - ADC HIGAIN HDSL2 Manual

152-231-116-01, Revision 01
Monitor Performance
------------------------------------------------------------------------------
Alarm
RLOS
RAIS
RAI
TX RAI-CI
PRM-NE
PRM-FE
DBER
------------------------------------------------------------------------------
Use <Space> to cycle through
choices and <Enter> to view
ID: xxxx--xxxx--xxxx--xxxx
Screen Alarm Front-Panel Alarm Description
H2TU-C DS1 ALARMS (see
(a)
LLOS LLOS
LAIS LAIS
DBER DBER
H2TU-R DS1 ALARMS (see
(a)
RLOS RLOS
RAIS RAIS
RAI RRAI
TX RAI-CI TRCI
PRM-NE PRMN
PRM-FE PRMF
DBER DBER
(a) This is a DS1-specific alarm that also issues a minor alarm (sent to the management unit or the backplane), if enabled.
(b) AIS-CI is a modified AIS alarm pattern. Equipment not suited to detect AIS-CI still detects this signal as an AIS. AIS-CI is sent
toward the network indicating that an LOS (RLOS) or AIS (RAIS) has been received from the CPE.
H2TU-C-231 List 1F
Event Log Config
H2TU-R DS1 Alarm History
First
09/01/2000 00:00
09/01/2000 00:37
Press: C(l)ear Alarm History
Interface
Statistics :
09/20/2000 14:35:13
Figure 24. H2TU-R DS1 Alarm History Screen
Table 14. DS1 Alarm Descriptions
Figure 23 on page 38)
Local Loss of Signal—Loss of the H2TU-C DSX-1 input signal.
Local Alarm Indication Signal—Indicates an AIS (all ones) pattern is being transmitted
from the local DS1 output port. The ALMP option determines whether AIS (default) or
LOS is sent towards the CPE.
Bit Error Rate—The DS1 BER has exceeded the built-in 24-hour threshold limits of
approximately 10
Figure 24 on this page)
Remote Loss of Signal— Loss of the H2TU-R DS1 input signal.
Remote Alarm Indication Signal—Indicates an AIS (all ones) pattern is being received at
the H2TU-R DS1 input port. By default AIS-CI
Figure 29 on page
Remote RAI - Remote Alarm Indication at the H2TU-R—Indicates an RAI alarm (yellow
LED) from the CPE with errors from the line unit or network.
Transmit RAI-CI - Remote Alarm Indication at the H2TU-R—Upon reception of an RAI
alarm (yellow LED) from the CPE, the H2TU-R sends a RAI-CI towards the network if the
network signal received at the H2TU-R is clear. If the network signal is impaired (LOS,
AIS, or LOF), then the RAI is passed on to the network unaltered. This is applicable to SF
or ESF framing. In an all SF environment, RACI must be enabled to convert SF RAI to SF
RAI-CI.
Performance Report Monitoring - Near End—The count of the PRM-NE register at the
H2TU-R exceeds the 10
Performance Report Monitoring - Far End—The count of the PRM-FE register at the
H2TU-R exceeds the 10
Bit Error Rate—The DS1 BER has exceeded the built-in 24-hour threshold limits of
approximately 10
Inventory Rlogon
Last Status
09/01/2000 00:45 ALARM
OK
OK
OK
DISABLED
DISABLED
09/01/2000 00:45 OK
: H2TU-R DS1
Alarm History
H2TU-C
-6
.
48).
-6
BER threshold at 648 events since 12:00:00 AM.
-6
BER threshold at 648 events since 12:00:00 AM.
-6
.
October 2, 2000
Monitoring System Activity and Performance
Help
Count
12
0
0
0
0
0
7
System: Alarm
(b)
is sent towards the network (see
39