Humminbird MEGA 360 UNIVERSAL Installation Manual
  1. Manuals
  2. Brands
  3. Humminbird Manuals
  4. Marine Equipment
  5. MEGA 360 UNIVERSAL
  6. Installation manual

Humminbird MEGA 360 UNIVERSAL Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MEGA 360 UNIVERSAL
INSTALLATION GUIDE
532750-3EN_A
1

Advertisement

Table of Contents
loading

Related Manuals for Humminbird MEGA 360 UNIVERSAL

Summary of Contents for Humminbird MEGA 360 UNIVERSAL

  • Page 1 MEGA 360 UNIVERSAL INSTALLATION GUIDE 532750-3EN_A...
  • Page 2 Always operate the boat at very slow speeds if you suspect shallow water or submerged objects. WARNING! The electronic chart in your Humminbird unit is an aid to navigation designed to facilitate the use of authorized government charts, not to replace them.
  • Page 3 NOTE: The procedures and features described in this manual are subject to change without notice. This manual was written in English and may have been translated to another language. Humminbird is not responsible for incorrect translations or discrepancies between documents.

  • Page 4: Table Of Contents

    Table of Contents Introduction Compatibility ........................1 Supplies .........................3 Update Software Software Requirements ....................4 Check the Current Software Version ................4 Update Control Head Software with an SD Card ............5 Update Accessory Software with an SD Card ..............6 Update Software with FishSmart ..................7 Install the Universal Boat Mount (select models) 1.
  • Page 5 Table of Contents Control Head Maintenance ..................25 Transducer Maintenance.....................26 Troubleshooting Fishing System Doesn’t Power Up ................27 Fishing System Defaults to Simulator with a Transducer Attached ......28 Finding the Cause of Noise ..................29 Specifications Contact Humminbird...

  • Page 7: Introduction

    This manual will guide you through the following installation requirements for the MEGA 360 Imaging transducer: • Installing the MEGA 360 Universal Boat Mount (select models) • Connecting to the Control Head and Power • Testing the Installation •...
  • Page 8 NOTE: If a MEGA SI+ transducer is connected with one of these y-cables, the Humminbird unit will not be able to get SI data from the MEGA SI+ transducer – only HW and MEGA DI+ will be available. However, the user can get MEGA SI data from the MEGA 360 transducer.

  • Page 9: Supplies

    Puck, a Heading Sensor GPS Adapter (APEX/SOLIX only), and transducer extension cables. For the most current list of compatible accessories, visit our Web site at humminbird.com. Supplies In addition to the hardware included with your accessory, you will need the following supplies: •...

  • Page 10: Update Software

    Update Software Your control head model may need a software update to work with the MEGA 360 Imaging transducer. We recommend that you read the following section completely before starting any software updates. Software Requirements • APEX/SOLIX Series: 3.640 and later •...

  • Page 11: Update Control Head Software With An Sd Card

    Update Control Head Software with an SD Card You will need an SD or microSD card (depending on your control head model). WARNING! Humminbird is not responsible for the loss of data files (waypoints, routes, tracks, groups, snapshots, recordings, etc.) that may occur due to direct or indirect damage to the unit’s hardware or software.

  • Page 12: Update Accessory Software With An Sd Card

    You will need an SD or microSD card (depending on your control head model). 1. Install a formatted SD or microSD card into the computer card slot. 2. Go to humminbird.com, and click Support > Software Updates. 3. Scroll down to Accessories and Mapping. The available software updates are listed as downloads under each accessory product.

  • Page 13: Update Software With Fishsmart

    Update Software with FishSmart You can use the FishSmart App to download and push software updates directly to your Humminbird control head or accessory. NOTE: Your control head must already be running software release 1.610 and later for HELIX Series or 3.110 and later for APEX/SOLIX Series to support this feature.

  • Page 14: Install The Universal Boat Mount (Select Models)

    1. Prepare for Installation 1. Determine where to mount the MEGA 360 Universal bracket. • Use a level to locate a suitable, flat area on the decking or gunwale. Confirm that the boat is level on the trailer, both from port to starboard and from bow to stern, by placing your level on the deck of the boat, first in one direction, then in the other.

  • Page 15: Install The Universal Boat Mount

    Unobstructed View 2. Install the Universal Boat Mount Once you have determined the mounting location, use one of the following installation instructions to install the GeigerTec mount (included with select models): A. Direct Installation B. Cannon Mounting Track Installation (separate purchase required) A.
  • Page 16 4. Place the universal bracket on the mounting surface and align the bolt holes with the drilled mounting holes. Apply anti-seize to the four (4) 1/4"-20 bolts (not included) and insert them through the bolt holes and into the drilled mounting holes.

  • Page 17: Cannon Mounting Track Installation (Separate Purchase)

    B. Cannon Mounting Track Installation (Separate Purchase Required) NOTE: To purchase a Cannon Mounting Track or for installation information, visit cannondownriggers.com. 1. Use a Philips head screwdriver to remove the screw securing your Cannon Track’s endcap to the mounting track, and disconnect the endcap. 2.

  • Page 18: Adjust The Pod Height And Install The Depth Collar

    4. Adjust the Pod Height and Install the Depth Collar 1. Loosen the bracket arms and rotate the bracket so that the MEGA 360 pod is positioned over the water. Adjusting the Bracket Installing the Mount...
  • Page 19 2. Adjust the pod shaft to the desired height. The MEGA 360 Imaging pod must be set below the keel and skeg, so that nothing is obstructing the ‘view’ of the rotating beams. 3. After you have established the pod height, slide the depth set collar through the cables and down the shaft.

  • Page 20: Route The Cables And Connect Power

    (y-cable). See Compatibility for the list of cables, and visit our Web site at www.humminbird.com/support/ installation-diagrams to view the wiring diagrams. 2. Route the cables to the chosen connection locations in Section 1: Prepare for Installation.
  • Page 21 (not included). WARNING! The MEGA 360 Imaging transducer should be connected to a main switch, fuse panel, or battery switch. Humminbird does not recommend connecting to a battery without a fuse and a switch. CAUTION! Some boats have 24 or 36 Volt electric systems, but the MEGA 360 Imaging transducer MUST be connected to a 12 VDC power supply.
  • Page 22 WARNING! If you are unable to obtain a battery switch and are forced to connect the power cable directly to the battery, be aware that this will drain the battery. Humminbird does not recommend connecting to a battery without the appropriate fuse and a switch.

  • Page 23: Set Up The Control Head

    Set Up the Control Head When the control head detects the MEGA 360 Imaging transducer, it will select it automatically as the 360 sonar source. The related views and menus will be added to the system. Use the following instructions to power on the control head and confirm the MEGA 360 Imaging transducer is detected by the unit.
  • Page 24 NOTE: For additional system status, select Home > Settings > Network > System Info. MEGA 360 Imaging Transducer Connected (SOLIX) MEGA 360 icon on the status bar MEGA 360 Imaging listed as transducer HELIX Series 1. Turn on the power source from the main switch. 2.

  • Page 25: Set Up The Transducer

    HELIX Accessory Test MEGA 360 Imaging listed as Connected 2. Set Up the Transducer APEX/SOLIX Series Your APEX/SOLIX control head will automatically detect the connected transducers. To review the selected sonar sources, open the Settings tool, and select CHIRP Sonar > Sonar Source. HELIX Series Use the following instructions to select the connected transducer for your control head.

  • Page 26: Test Mega 360 Imaging On The Control Head

    Selecting the Connected Transducer (HELIX) 3. Test MEGA 360 Imaging on the Control Head It is important to confirm that the MEGA 360 Imaging transducer is providing sonar returns to the display. The instructions in this section should be performed at trolling speeds in calm, open water, in a large area that is far from shallow water, boats, or other obstacles.
  • Page 27 4. Stop Pinging: When you are finished reviewing the operation, tap Ping Off from the 360 status bar. HELIX Series 1. Press and hold the VIEW key. 2. Select Sonar > 360 View. 3. The sonar returns from the MEGA 360 scan will begin to display on the MEGA 360 View.

  • Page 28: Add Offset Features To The Mega 360 Imaging Display (Optional)

    4. Add Offset Features to the MEGA 360 Imaging Display (optional) The menu settings in this section are helpful for interpreting the position of objects on the 360 View. This feature is only available with a connected heading sensor (compass). Adjust the 360 Heading Offset If the positions of objects on the MEGA 360 Imaging display are slightly different than what you observe in the environment around you, use 360 Heading Offset...

  • Page 29: Set Up The Network

    HELIX Series 1. Main Menu: Press the MENU key twice. 2. Select the Accessories tab > MEGA 360 Settings > 360 Heading Offset. 3. Press the RIGHT or LEFT Cursor keys to change the angle (gray line), and press the CHECK/INFO key to confirm your setting. The zero point on the display is represented by a green line.

  • Page 30: Power Off

    WARNING! During transport, on water or on land, it is important to stow the MEGA 360 universal mount inside the rub rail of the boat. Possible Stowage Configuration Power Off...

  • Page 31: Maintenance

    Maintenance Your Humminbird fish finder is designed to provide years of trouble free operation with very little maintenance. Use the following procedures to ensure your Humminbird continues to deliver top performance. MEGA 360 Imaging Maintenance Use the following information to maintain the installation of the MEGA 360 Imaging Transducer.

  • Page 32: Transducer Maintenance

    Use the following information to keep the control head and screen clean. • Screen: To clean the control head screen, use a mild soap (such as a nonabrasive liquid hand soap) and warm water. Wipe the screen dry with a soft cloth.

  • Page 33: Troubleshooting

    Troubleshooting Before contacting the Humminbird Technical Support, please read the following section. Taking the time to review these troubleshooting guidelines may allow you to solve a performance problem yourself, and therefore avoid sending your unit back for repair. Fishing System Doesn’t Power Up If your Fishing System doesn’t power up, use the installation guide that is included...

  • Page 34: Fishing System Defaults To Simulator With A Transducer Attached

    Fishing System Defaults to Simulator with a Transducer Attached In addition to the MEGA 360 Imaging accessory transducer, you will have a standard Humminbird transducer connected to the control head. A connected and functioning transducer with built-in temperature will cause the newly-started Fishing System to go into Normal operating mode automatically.

  • Page 35: Finding The Cause Of Noise

    Finding the Cause of Noise Electrical noise usually affects the display with streaks or repetitive patterns on the view. One or more of the following sources can cause noise or interference: Possible Source of Noise Isolation Other electronic devices Turn off any nearby electronic devices to see if the problem goes away, then turn them on one at a time to see if the noise re-appears.

  • Page 36: Specifications

    Operating Temperature ........-4°F to 158°F (-20°C to 70°C) Storage Temperature ........-40°F to 158°F (-40°C to 70°C) NOTE: Humminbird verifies maximum stated depth in saltwater conditions, but actual depth performance may vary due to transducer installation, water type, thermal layers, bottom composition and slope.
  • Page 37 ROHS STATEMENT: Product designed and intended as a fixed installation or part of a system in a vessel may be considered beyond the scope of Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

  • Page 38: Contact Humminbird

    Contact Humminbird Contact Humminbird Technical Support through our Help Center at https:// humminbird-help.johnsonoutdoors.com/hc/en-us or in writing to the address below: Humminbird Service Department 678 Humminbird Lane Eufaula AL 36027 USA Social Media Resources: Facebook.com/HumminbirdElectronics Twitter.com (@humminbirdfish) Instagram.com/humminbirdfishing YouTube.com/humminbirdtv Contact Humminbird...

Table of Contents