Input/Output Setup; Cm V6/169Cs/7Mx/7Cxs/11Cv+/11Cvs+: Gps Connection; Gps Setup Menu; Autopilot Connection - Interphase Chart Master Chart Master 11 CVS+ User Manual

[MENU] + "SETUP" + [ENTER] + "COMPASS" + [ENTER]
Bearings
Variation
Calibration
4.7

INPUT/OUTPUT SETUP

GPS Connection CM V6/169CS/7MX/7CXS/11CV+/11CVS+
Connects the GPS to the GPS Port (serial Port 3). To choose your preferred
setting follow the procedure:
[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 3 In-
put" + [ENTER] + "NMEA-4800-N81-N" + [ENTER]

GPS Setup Menu

To set your desired configuration for the connected GPS.
Internal GPS
Restart GPS
Diff. Corr. Source
Navigation Speed

Autopilot Connection

Connect the Autopilot to the serial Port 1, 2 or 3 (CM 11CV+/11CVS+: it is
possible to select the Port 4 and 5 too).
[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1/2/3
(CM 11CV+/11CVS+: ports 4/5 too) Output" + [ENTER]
Then choose your preferred setting among the NMEA available settings NMEA
0183 4800-N81-N, NMEA 0180, NMEA 0180/CDX and press [ENTER] to confirm.

External NMEA Connection

Connect the External NMEA to the serial Port 1, 2 or 3 (CM 11CV+/11CVS+: it is
possible to select the Port 4 and 5 too).
[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1/2/3
(CM 11CV+/11CVS+: ports 4/5 too) Input" + [ENTER]
Then choose your preferred setting among the NMEA available settings NMEA
1200-N81-N, NMEA 4800-N81-N, NMEA 4800-N82-N, NMEA 9600-O81-N, NMEA
9600-N81-N and press [ENTER] to confirm.

C-COM GSM PLUS Connection

[MENU] + "SETUP" + [ENTER] + "Input/Output" + [ENTER] + "Port 1 In-
put" + [ENTER] + "C-COM" + [ENTER]
The modem C-COM can be connected also to the Port 2, 3 (CM 11CV+/11CVS+:
it is possible to select the Port 4 and 5 too), in this case select the format on the
used port.
NOTE The connection is valid for the C-COM IR and C-COM RS232 too.
44
: Selects either degrees magnetic or degrees true. If magnetic readings are
selected the variation is computed automatically for every zone as soon as the
chart is displayed.
: It is possible to calculate the Magnetic Variation in an Automatic or Manual
mode, by inserting the step for calculation of Magnetic Variation.
: The variation table is used to match magnetic value readout on the chartplotter
comparable with the value given by the compass of the boat. In other words,
since the compass of the boat must be compensated (due to the iron masses,
...), we use the same values given by the chartplotter. This means that, for
example, if the BRG to the next Waypoint readout in the chartplotter display is
"X" Mag degree, if you steer the boat reading "X" Mag degree from the compass,
you are driving well toward the next Waypoint.
: CM V6i/169CSi/7Mi/7Ci Enables or disables the Internal GPS.
: Restarts all GPS processes. Once executed, the message "Done" is shown.
: Sets what kind of Differential Correction will be used by the GPS between WAAS
and RTCM (beacon correction).
: Sets the Navigation Speed among Low Speed, Medium Speed and High Speed.
User Manual