Remote Control; How To Install Batteries; Battery Precautions - Insignia IS-TV040924 Owner's Manual

REMOTE CONTROL

1
POWER
1 2
2
4
7 8
3
0
DISPLAY
4
SLEEP
5
VOL
–
6
MENU
EXIT
7
TV/AV
8
1. POWER Button - Press to turn the TV on. Press again to
turn the TV off.
2. Direct Channel Selection Buttons (0-9) - Allows direct
access to any channel.
3. DISPLAY Button - When you press this button, the
channel number will appear in the upper right corner of
the screen. Press the button again to remove display from
the screen.
Before using the remote control, batteries must first be installed.

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.
2. Install two "AAA" batteries (not supplied).
3. Replace the battery compartment cover.
3U20431A [E] P02-08
3
5 6
9
9
QUICK VIEW
10
MUTE
CH
11
VOL
+
12
ENTER
CH
RESET
13
AUDIO CLOSED
SELECT CAPTION
14
15
5
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button. The clock will
count down 10 minutes each time the button is pressed in
the order of 120, 110, 100, ······ 20, 10, 0. After the sleep
time is programmed, the display will disappear then reappear
momentarily every ten minutes to remind you the sleep
timer function is operating. To confirm the sleep time setting,
press the SLEEP button once and the remaining time will
be momentarily displayed. To cancel sleep time, press the
SLEEP button repeatedly until the display turns to 0.
5. VOL (VOLUME) / Buttons - Press the
increase, or the button to decrease the volume level.
6. MENU Button - Press to display the On-Screen menu
function.
7. EXIT Button - Press remove setup menu.
8. TV/AV Button - Switches between TV and external inputs.
9. QUICK VIEW Button - This button allows you to go back to
the previous channel selected by just pressing the QUICK
VIEW button. Press this button again to return to the channel
you were watching.
10. MUTE Button - To turn off the sound, press this button
once. The TV will be silenced and the symbol "MUTE" will
appear on the screen. The muting feature can be released
by pressing the MUTE button again or one of the VOL
or button.
11. CH (CHANNEL) / Buttons - Press the
change to a higher numbered channel set into memory.
Press the button to change to a lower numbered channel
set into memory.
12. ENTER Button - Press to enter or select information for
On- Screen operations.
13. RESET Button - Press to reset the On-Screen picture
adjustments to their factory preset positions.
14. CLOSED CAPTION Button - Press this button to switch
between normal TV and the two Closed Caption modes
(captions and 1/2 of full screen text). Closed Captioning
will display text on screen for hearing impaired viewers.
15. AUDIO SELECT Button - Switches sound between mono
and stereo when receiving broadcasts in stereo.
Use two "AAA" size batteries. The batteries may last
approximately one year depending on how much the remote
control is used. For best performance, it is recommended
that batteries should be replaced on a yearly basis, or when
the remote operation becomes erratic. Do not mix old and
new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not try to recharge batteries not intended to be recharged;
they can overheat and rupture (follow battery manufacturer's
directions).
2/21/05, 6:25 PM
button to
button to
5