Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel SINGLE DISHDRAWER DD24STX6PX1
Summary of Contents for Fisher & Paykel SINGLE DISHDRAWER DD24STX6PX1
- Page 1 SINGLE DISHDRAWER™ DISHWASHER CONTEMPORARY DD24STX6PX1 INSTALLATION GUIDE US CA...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance. Electric Shock Hazard Failure to follow this advice may result in Servicing Do not repair or replace any part of the appliance unless specifically recommended in electrical shock or death. -
Page 4: Tools And Components
TOOLS AND COMPONENTS PARTS SUPPLIED TOOLS REQUIRED Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 5: Product Dimensions
PRODUCT DIMENSIONS PRODUCT DIMENSIONS INCHES A Overall height B Overall width 23 5/8 C Overall depth 22 9/16 D Depth of chassis 21 3/4 E Height of door panel 17 3/8 PLAN ISOMETRIC F Depth of door panel G Ventilation gap below door panel 5/16 H Height from top of drawer panel to top of chassis 1/16... - Page 6 CABINETRY DIMENSIONS CLEARANCES Connections can be located in an adjacent cabinet on either side of the DishDrawer™ Dishwasher** PLAN ISOMETRIC CABINETRY DIMENSIONS INCHES CABINETRY CLEARANCES INCHES A Minimum clearance to adjacent cupboard door 1/16 A Minimum inside height 17 15/16 B Minimum clearance to corner cupboard B Inside width 23 5/8...
- Page 7 PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher &...
- Page 8 HARD-WIRING (OPTIONAL) You have the option to hard-wire your DishDrawer™ Dishwasher. To do this, we recommend to remove the supplied power cord and do the hardwiring installation as close to the cavity as possible. Lift the cover upwards until you are able to pull out towards you to remove.
- Page 9 HARD-WIRING (OPTIONAL) Fix the Live and Neutral wires to the terminal block and the Earth wire to Ensure the hoses are not twisted before the chassis. refitting the drawer to the runners and clipping into place via both locking tabs. rear L rib hook...
- Page 10 CABINETRY PREPARATION SERVICE ACCESS MOISTURE PROTECTION We recommend locating the service holes on either side of the DishDrawer as shown below. If the hole is created through wood, ensure the edges are smooth and rounded If the holes is created through metal, ensure the edge protector is fitted. Align the supplied moisture protection tape to the cabinetry as illustrated Ensure this area is free of debris...
- Page 11 SECURE TO CABINETRY VIA BRACKETS (METHOD A) Secure all four side brackets to the DishDrawer™ Dishwasher, aligning Secure to cabinetry via the brackets. bracket A with slot A and bracket B Pre-drilling a pilot hole may be required with slot B. depending on the cabinetry material.
- Page 12 SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Push the product into the cavity, pulling the hoses through as you push to avoid Secure to cabinetry via all three fixing crushing or twisting them and taking locations in the tub. care not to bend the legs.
- Page 13 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of the countertop as possible.
- Page 14 PLUMBING & ELECTRICAL CONNECTION SINGLE AIR GAP INSTALLATION Ensure the supplied rubber washer is fitted to the coupling before connecting Install your single Air Gap Kit to the the inlet hose to tap. benchtop like shown. Tighten using a spanner or pliers, Refer to ‘Plumbing &...
-
Page 15: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Installation Electrical … Check all parts are installed correctly and are secure. … Ensure all electrical tests have been conducted in accordance with local regulations. … Ensure all clearance gaps have been maintained. Test operation …... -
Page 16: Troubleshooting
TROUBLESHOOTING No program indicator lights up when the drawer is opened DISPLAY POSSIBLE CAUSE WHAT TO DO Ensure power is connected and is switched on. Water 1 Ensure the water supply is turned on. may need to be activated. Refer to your user guide for details. AUTO POWER-ON Supply fault. - Page 17 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2021. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.