Hoshizaki KML-631MAH Instruction Manual
Low-profile modular crescent cuber
Hide thumbs
Also See for KML-631MAH:
- Service manual (58 pages) ,
- Instruction manual (32 pages) ,
- Specifications (2 pages)
Related Manuals for Hoshizaki KML-631MAH
Summary of Contents for Hoshizaki KML-631MAH
- Page 1 Hoshizaki America, Inc. “A Superior Degree of Reliability” www.hoshizaki.com Low-Profile Modular Crescent Cuber Models KML-631MAH KML-631MWH KML-631MRH INSTRUCTION MANUAL ™ Issued: 3-16-2007 Revised: 11-14-2007...
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write or send an e-mail message to the HOSHIZAKI Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
• Keep this manual with the icemaker for later reference. I. Specifications ... 4 A. Nameplate Rating ... 4 1. KML-631MAH (air-cooled) ... 4 . KML-631MWH (water-cooled) ... 5 3. KML-631MRH (remote air-cooled) ... 6 B. Dimensions/Connections ... 7 1. -
Page 4: Specifications
I. Specifications A. Nameplate Rating 1. KML-631MAH (air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR PUMP OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER(USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED, See the nameplate for electrical and refrigeration specifications. -
Page 5: Kml-631Mwh (Water-Cooled)
2. KML-631MWH (water-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR PUMP OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER(USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED, See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of rear panel. -
Page 6: Kml-631Mrh (Remote Air-Cooled)
3. KML-631MRH (remote air-cooled) HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE COMPRESSOR PUMP FAN REMOTE OTHER MAXIMUM FUSE SIZE MAX. HACR BREAKER(USA ONLY) MAX. CIRC. BREAKER (CANADA ONLY) MINIMUM CIRCUIT AMPACITY DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED, See the nameplate for electrical and refrigeration specifications. -
Page 7: Dimensions/Connections
B. Dimensions/Connections 1. KML-631MAH Unit: inches (mm) -
Page 8: Kml-631Mwh
2. KML-631MWH Unit: inches (mm) -
Page 9: Kml-631Mrh
3. KML-631MRH Unit: inches (mm) -
Page 10: Installation And Operating Instructions
6) See the nameplate on the rear panel, and check that your voltage supplied corresponds with the voltage specified on the nameplate. 7) This icemaker needs a storage bin. The recommended storage bin is HOSHIZAKI ICE STORAGE BIN, Model B-500 series, DB-00, or DM series. -
Page 11: Location
C. Location This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Normal operating water temperature should be within +45°F to +90°F (+7°C to +3°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect production capacity. -
Page 12: Electrical Connection
E. Electrical Connection 1. Electrical connection must be made in accordance with the instructions on the "WARNING" tag, provided with the pig tail leads in the junction box. . This icemaker requires a ground that meets the national and local electrical code requirements. -
Page 13: Installation Of Remote Condenser Unit
F. Installation of Remote Condenser Unit 1. Checks Before Installation 1) Remove the shipping carton, tape, and packing material. ) Check that the refrigerant lines do not rub or touch lines or other surfaces, and that the fan blade moves freely. 2. -
Page 14: Setup
) The legs have eight mounting holes. Secure the legs with eight bolts (not included). 4. Line Set • Precharged tubing kits, available as optional equipment from HOSHIZAKI AMERICA, are recommended. Field fabricated line sets are allowed, see instructions below. - Page 15 ) Insulate the two copper tubings separately. 3) Install Parker quick connect couplings on each end. OS-QUICK, a universal quick connect coupling kit available as optional equipment from HOSHIZAKI AMERICA, is recommended. 4) Evacuate through the charging ports on the Parker quick connect couplings and charge with R-404A refrigerant vapor to a pressure of 15 to 30 PSIG.
-
Page 16: Electrical Connection
5. Electrical Connection 1. Electrical connections must meet national, state, and local electrical code requirements. Failure to meet these code requirements could cause severe injury to individuals or extensive damage to equipment. . Be sure to install a proper ground from the icemaker to the remote condenser unit. -
Page 17: Water Supply And Drain Connections
G. Water Supply and Drain Connections See Fig. 9 Do not operate the icemaker when the water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar). Do not run the icemaker until the proper water pressure is reached. •... - Page 18 KML-631MAH KML-631MRH KML-631MWH Fig. 9...
-
Page 19: Final Checklist
H. Final Checklist 1) Is the icemaker level? ) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +3°C) all year around? 3) Is there at least 6"... -
Page 20: Startup
I. Startup 1. All parts are factory-adjusted. Improper adjustments may result in failure. . If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 3. Do not operate the unit in the "WASH" position without water in the water tank. -
Page 21: Cleaning And Maintenance Instructions
1. Cleaning Procedure 1) Dilute approximately 13.5 fl. oz. of recommended cleaner Hoshizaki "Scale Away" or "LIME-A-WAY," (Economics Laboratory, Inc.) with .5 gallons of water. ) Remove all ice from the evaporator and the storage bin. -
Page 22: Sanitizing Procedure - Following Cleaning Procedure
19) Replace the front panel in its correct position. 0) Turn on the power supply to fill the water tank with water. 1) Turn off the power supply after 3 minutes. ) Remove the front panel. 3) Move the control switch to the "SERVICE" position, then move the service switch to the "WASH"... -
Page 23: Preparing The Icemaker For Long Storage
B. Maintenance This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 2. - Page 24 5) Open the water regulating valve by using a screwdriver to pry up on the spring retainer underneath the spring. While holding the valve open, blow out the condenser using the compressed air or carbon dioxide supply until water stops coming out. 6) Close the condenser water supply line drain valve and replace the right side panel in its correct position.
- Page 25 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A1HH10B...