Table of Contents
Advertisement
Quick Links
Installation and
Service Instructions
for use by heating contractor
BMS communication with heating systems via BACnet
WAGO BACnet/IP gateway
WAGO BACnet/IP GATEWAY
6175 795 - 03
07/2022
Product may not be exactly as shown
Product may not be exactly as shown
IMPORTANT
IMPORTANT
Read and save these instructions
Read and save these instructions
for future reference.
for future reference.
Please file in Service Binder
Advertisement
Table of Contents
Related Manuals for Viessmann WAGO BACnet/IP
Summary of Contents for Viessmann WAGO BACnet/IP
- Page 1 Installation and Service Instructions for use by heating contractor BMS communication with heating systems via BACnet WAGO BACnet/IP gateway WAGO BACnet/IP GATEWAY Product may not be exactly as shown Product may not be exactly as shown IMPORTANT IMPORTANT Read and save these instructions Read and save these instructions for future reference.
-
Page 2: Safety, Installation And Warranty Requirements
Safety WAGO Gateway Installation and Service Safety, Installation and Warranty Requirements Safety, Installation and Warranty Requirements Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the instructions listed below and details printed in this manual can cause product/property damage, severe personal injury, and/or loss of life. -
Page 3: Table Of Contents
Table of Contents WAGO Gateway Installation and Service Page Page Safety Safety, Installation and Warranty Requirements ....2 Product documentation ..........2 Licensed professional heating contractor ....2 Advice to owner ...........2 Warranty ..............2 General Information Important Regulatory and Installation Requirements ..4 Approvals .............4 Codes ..............4 Working on the equipment........4... -
Page 4: Important Regulatory And Installation Requirements
Important Regulatory and Installation Requirements Approvals Please carefully read this manual prior to attempting Viessmann boilers, burners and controls are approved for installation. Any warranty is null and void if these sale in North America by CSA International. instructions are not followed. -
Page 5: Intended Use
Incorrect usage or operation of the appliance (e.g. the appliance being opened by the system user) is prohibited and will result in an exclusion of liability. Incorrect usage also occurs if the components in the Viessmann system are modified from their intended function. Product Information The WAGO BACnet/IP gateway is used to connect Viessmann control units to BACnet systems. -
Page 6: Mounting The Gateway
Installation WAGO Gateway Installation and Service Mounting the Gateway 1. Loosen the retaining screws from the extension kit enclosure (do not remove). 2. Remove cover and set aside. 3. Mount the extension module enclosure to the wall using the appropriate hardware. -
Page 7: Preparing For Installation
Installation WAGO Gateway Installation and Service Preparing for Installation WAGO BACnet gateway system overview Legend A Viessmann boiler B Building management system C Terminator 120 D Gateway E Power supply unit F Laptop with web browser and WAGO Web-Visu... -
Page 8: Quick Start Guide Wago Bacnet
Installation WAGO Gateway Installation and Service Quick Start Guide WAGO BACnet Install WAGO Gateway Power up and connect WAGO Gateway to heat generators via CAN-Bus (91 plug). H Power Supply 24VDC (116 mA, 2.8 W) H Polarity sensitive (H, and L) H Daisy chain using (ISO 11898-2, twisted pair cable, shielded, or CAT5 / CAT7) H End resistors (or dip switch) on both ends of the... - Page 9 Installation WAGO Gateway Installation and Service Quick Start Guide WAGO BACnet (continued) Add Data points Navigate to Datapoints / CAN-Status Make sure you see all the heat generators you want to add to the system Select “Show Datapoints” and Confirm action to discover points Select the points you want to add to the BMS Note: You must do this step for each heat generator...
- Page 10 Installation WAGO Gateway Installation and Service Quick Start Guide WAGO BACnet (continued) WAGO BACnet Configurator - Set BACnet Device ID (Optional) Note: download the tool from the link on the left. 1. Scan the network for BACnet devices 2. Right click on the WAGO Gateway, and select “Add to Database”...
-
Page 11: Process Overview
Installation WAGO Gateway Installation and Service Process Overview Step Responsibility Page Install the module. Contractor Establish the CAN bus connection. Contractor Connect the plug-in attachment. Contractor Establish the connection to the BACnet. IT expert/system integrator Power supply Electrician Commission the gateway. IT expert/system integrator Installing the Module IMPORTANT... -
Page 12: Connections And Operating Elements
Installation WAGO Gateway Installation and Service Connections and Operating Elements WAGO BACnet/IP gateway Legend A Serial interface N Operating mode switch B LED status indicators RUN Standard mode C Reset button RST Factory setting: Do not adjust! D Status LED for supply voltage STOP Only for update process;... - Page 13 H Check installation and connections of gateway and power supply unit. H If the fault cannot be rectified, contact Viessmann Technical Service. Other Fault Contact Viessmann Technical Service. Power supply unit Legend A INPUT 120VAC, 60 Hz B OUTPUT 24VDC, 1.3A...
-
Page 14: Connecting And Releasing Cores
Installation WAGO Gateway Installation and Service Connecting and Releasing Cores Connections Gateway 1. Insert a small flat head screwdriver into the opening direcly above the wire.. 2. Tilt the handle of the screwdriver up. 3. Pull the wire straight out. Example: BACnet/IP gateway Power supply unit 1. -
Page 15: Establishing The Can Bus Connection
Installation WAGO Gateway Installation and Service Establishing the CAN Bus Connection H The Viessmann CAN bus is designed for “line” bus topology with a terminator at both ends (accessories). H With CAN bus, the transmission quality and the cable lengths depend on the electrical properties of the cable: –... - Page 16 Installation WAGO Gateway Installation and Service Establishing the CAN Bus Connection (continued) Legend A CAN bus shield B Cable for lA for controlling the boiler (standard delivery of the gateway) Installation and service instructions for boiler control unit...
-
Page 17: Connecting The Plug-In Attachment
Installation WAGO Gateway Installation and Service Connecting the Plug-in Attachment WAGO BACnet/IP gateway The plug-in attachment (standard delivery) must be plugged in. Do not connect the plug-in attachment until the CAN bus cable has been connected. If the gateway is at the beginning or end of the CAN bus:... -
Page 18: Establishing The Connection To The Bacnet/Ip Gateway
Installation WAGO Gateway Installation and Service Establishing the Connection to the BACnet/IP Gateway The connection to the network must be established by the system integrator. Legend A Connect BACnet/IP via RJ45 interface... -
Page 19: Connecting The Gateway To The Power Supply Unit
Installation WAGO Gateway Installation and Service Connecting the Gateway to the Power Supply Unit Connecting cores in the power supply unit. Legend A Cable cores between gateway and power supply The WAGO gateway is supplied in the encloser with the unit (standard delivery) power supply unit prewired to the gateway. -
Page 20: Power Supply
Installation WAGO Gateway Installation and Service Power Supply General information The WAGO gateway comes complete with a 6 ft. (2 m) IMPORTANT power cord with convience plug for simplified installation. Electrical installations must comply with the latest edition of: WARNING In the U.S.A., the National Electrical Code (NEC), ANSI/NFPA 70 and any other state, local codes and/or The control must be grounded. -
Page 21: Commissioning The Gateway
Installation WAGO Gateway Installation and Service Connecting the Plug-in Attachment Commissioning the Gateway (continued) Commissioning must be carried out by the IT expert or system integrator. 1. Switch on the boiler. 2. Switch on the power supply for the gateway. 3. -
Page 22: Dismounting The Gateway
Installation WAGO Gateway Installation and Service Dismounting the Gateway Connecting the Plug-in Attachment Dismounting the controller Connecting the Plug-in Attachment Dismounting the Power Supply Unit... - Page 23 Specifications WAGO Gateway Installation and Service Connecting the Plug-in Attachment Gateway (continued) WAGO BACnet/IP gateway Power supply 24VDC Power consumption Max. 116 mA Nominal rating 2.8 W Permissible ambient temperature H Operation 32 to 104°F (0 to 40°C) H Storage -4 to 140°F (–20 to +60°C)
-
Page 24: Power Supply
Specifications WAGO Gateway Installation and Service Connecting the Plug-in Attachment Power Supply Power supply unit Rated voltage 100 to 240V~ Rated frequency 50 to 60 Hz Rated current 1.34A Output voltage 24VDC Permissible ambient temperature H Operation 32 to 104°F (0 to 40°C) H Storage and transport -40 to 185°F (–40 to +85°C) Dimensions... -
Page 25: Final Decommissioning And Disposal
WAGO Gateway Installation and Service Connecting the Plug-in Attachment Final Decommissioning and Disposal (continued) Viessmann products can be recycled. Components and substances from the system are not part of ordinary household waste. For decommissioning the system, isolate the system from the power supply and allow components to cool down where appropriate. - Page 26 WAGO Gateway Installation and Service...
- Page 27 WAGO Gateway Installation and Service...
- Page 28 WAGO gateway Installation and Service...