Denon AVR-X2300W Service Manual page 122

Paths to be confirmed Display
fig.04a
4 HDMI
A05:HDMI
fig.04b
Analog AD fig.05a
5
A06:AD
(MAIN) fig.05b
Analog Amp Assign
6 (Amp Assign : fig.06
A07:ASSIGN-Z2
ZONE2)
1.6. Confirmation items for the video system
See the block diagram fig.XXth.
Paths to be confirmed Display
fig.07
1 Analog Video pass
V01:VIDEO PASS
Video Convert
2 fig.08
V02:V.CONVERT
(HDMI ⇒ HDMI)
HDMI pass
3 fig.09
V03:HDMI PASS
(MAIN ZONE)
HDMI CEC
fig.10
4 (Control Monitor :
V04:HDMI CEC
HDMI Monitor1)
Settings
Input Source : CBL/SAT
Input Mode : HDMI (fixed)
Sound mode : STEREO
Amp assign : Surround Back
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Analog (fixed)
Sound mode : MULTI CH STEREO
Vol 60dB
Amp assign : Surround Back
Speaker Config ALL Speaker = Small / SW = Yes(2ch)
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Input Mode : Auto
Sound mode : STEREO
Z2 Source : Source
Vol 60dB
Amp assign : ZONE2
MAIN ZONE : On
ZONE2 : On
Settings
Input Source : CBL/SAT
MAIN ZONE : On
ZONE2 : On
Input Source : CBL/SAT
Video Mode (IP Scaler) : "Auto", All sources
IP Scaler : "HDMI", All sources
Resolution : "Auto", All sources
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
Video Mode (IP Scaler) : Bypass (S920 / X2300 ONLY)
MAIN ZONE : On
ZONE2 : Off
Input Source : CBL/SAT
HDMI Control : On
Control Monitor : Monitor1 (if checking the HDMI
Monitor Out1)
MAIN ZONE : On
ZONE2 : Off
122
What to confirm
・ HDMI input ⇒ Speaker output (Front L/R)
( b The input source can be switched to any source except CBL/SAT.)
・ Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R, Surround Back L/R)
・ Analog input ⇒ Speaker output, SW(20Hz) (Front L/R, Center, Surround L/R, Surround Back L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20dB when Relative
settings are used)
・ Analog input ⇒ Speaker output (Surround Back (ZONE2) L/R)
・ Analog input ⇒ Pre OUT output (ZONE2 L/R)
( b The input source can be switched to any source except CBL/SAT.)
( b Volume 60 is the value when Absolute settings are used. The value is -20dB when Relative
settings are used)
What to confirm
・ CVBS input ⇒ CVBS output
・ Component input ⇒ Component output (S910 / X2200E3 ONLY)
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input ⇒ IP Scaler ⇒ HDMI output.
・ ETHERNET input ⇒ IP Scaler ⇒ HDMI output.
( b The input source can be switched to any source except CBL/SAT.)
・ HDMI input (MAIN function) ⇒ HDMI output (MAIN)
( b The input source can be switched to any source except CBL/SAT.)
・ When the power supply of a TV is put in the standby mode, make sure that the power supply
of this unit is also put in the standby mode.
( b The input source can be switched to any source except CBL/SAT.)
・ The ARC path can also be checked (check this using the TV input source).