Motorola MSF 5000 Instruction Manual page 226

Appendix
B
Error Codes MSF
5000
Instruction Manual
Operational Error Code Definition
Table B-1
Operational Error Codes (Continued)
Error
Description
Probable Cause
Corrective Action
E3A EEPOT
9
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust EEPOT
9.
Refer
to
Chapter 4,
(high
end
equalization level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3b
EEPOT
A
upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT A.
Refer
to
Chapter 4,
(low
end
equalization level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3C EEPOT
b
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
b.
Refer
to
Chapter
4,
(trunking
data
level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3d
EEPOT C upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
C. Refer
to
Chapter
4,
(line
2
output level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3E
EEPOT
d
upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
d. Refer
to
Chapter
4,
(line
4
output level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3F EEPOT F
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
F.
Refer
to
Chapter 4,
(SAM
encode
level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E40
RX_Loop_Ctrl
line not changing
The RX1 Loop signal
is not
toggling
Replace Uniboard.
states as
expected,
indicating
a
bad receiver
synthesizer.
E41
TX_Loop_Ctrl
line not changing
The
TX
Loop signal is not toggling
as
Replace Uniboard.
states
expected, indicating
a
bad
transmitter synthesizer.
E42
time in
CP
<
1
hour
Muti-Coded Squelch (MCS)
update
MCS
air-time accumulator update
Reprogram
the
SSCB codeplug
to set
time in
the
codeplug
is less than one the
update time value
to
at least one
hour.
A
value of one hour is assumed hour. Refer to
the
RSS
manual.
by
the
firmware.
E43
Error while copying user
table to
MCS
board is not accepting the user
Verify power
to
MCS
board
MCS
board table serial data transfer due to one
of
the
following
conditions:
Verify JU1 is
configured
to enable
EEPROM
writes
¢
No power
to
MCS
board
Replace defective
EEPROM
¢
JU1 configured incorrectly
Replace
MCS
board
¢
Defective
EEPROM
on
MCS
board
E44 Error in update_MCS while The IPCB signal was temporarily
No
action required, this error should
converting ascii
to
hex
corrupted
while transferring user self-correct.
table data between the
SSCB
and
MCS
modules, resulting in
non-ASCII
data
being received by
the
SSCB.
E45 Cannot adjust receiver
to
saved level Corrupted SSCB. Reprogram. Refer
to the
RSS
manual
E46 Transmit synthesizer failed
to
unlock Faulty SSCB.
Replace SSCB.
after
"Change_Freq" pulse
Faulty
VCO.
Replace
VCO.
E47 Transmit synthesizer failed
to
lock Recent frequency change or bad
Reprogram SSCB
or retune
Tx VCO.
after three
program attempts
VCO
B-4
68P81092E09
3/19/94
Appendix
B
Error Codes MSF
5000
Instruction Manual
Operational Error Code Definition
Table B-1
Operational Error Codes (Continued)
Error
Description
Probable Cause
Corrective Action
E3A EEPOT
9
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust EEPOT
9.
Refer
to
Chapter 4,
(high
end
equalization level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3b
EEPOT
A
upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT A.
Refer
to
Chapter 4,
(low
end
equalization level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3C EEPOT
b
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
b.
Refer
to
Chapter
4,
(trunking
data
level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3d
EEPOT C upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
C. Refer
to
Chapter
4,
(line
2
output level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3E
EEPOT
d
upper limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
d. Refer
to
Chapter
4,
(line
4
output level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E3F EEPOT F
upper
limit out-of-bounds
Alignment
procedure attempted
to
Adjust
EEPOT
F.
Refer
to
Chapter 4,
(SAM
encode
level)
adjust
EEPOT
beyond maximum
Alignment.
setting.
E40
RX_Loop_Ctrl
line not changing
The RX1 Loop signal
is not
toggling
Replace Uniboard.
states as
expected,
indicating
a
bad receiver
synthesizer.
E41
TX_Loop_Ctrl
line not changing
The
TX
Loop signal is not toggling
as
Replace Uniboard.
states
expected, indicating
a
bad
transmitter synthesizer.
E42
time in
CP
<
1
hour
Muti-Coded Squelch (MCS)
update
MCS
air-time accumulator update
Reprogram
the
SSCB codeplug
to set
time in
the
codeplug
is less than one the
update time value
to
at least one
hour.
A
value of one hour is assumed hour. Refer to
the
RSS
manual.
by
the
firmware.
E43
Error while copying user
table to
MCS
board is not accepting the user
Verify power
to
MCS
board
MCS
board table serial data transfer due to one
of
the
following
conditions:
Verify JU1 is
configured
to enable
EEPROM
writes
¢
No power
to
MCS
board
Replace defective
EEPROM
¢
JU1 configured incorrectly
Replace
MCS
board
¢
Defective
EEPROM
on
MCS
board
E44 Error in update_MCS while The IPCB signal was temporarily
No
action required, this error should
converting ascii
to
hex
corrupted
while transferring user self-correct.
table data between the
SSCB
and
MCS
modules, resulting in
non-ASCII
data
being received by
the
SSCB.
E45 Cannot adjust receiver
to
saved level Corrupted SSCB. Reprogram. Refer
to the
RSS
manual
E46 Transmit synthesizer failed
to
unlock Faulty SSCB.
Replace SSCB.
after
"Change_Freq" pulse
Faulty
VCO.
Replace
VCO.
E47 Transmit synthesizer failed
to
lock Recent frequency change or bad
Reprogram SSCB
or retune
Tx VCO.
after three
program attempts
VCO
B-4
68P81092E09
3/19/94