Table of Contents
Advertisement
DVDPak2 Settings
Video Display Settings
If the camera view does not display on the DVDPak2
monitor, perform the following functions to correct the
video display source:
1� Press the Return Button
Menu of the DVDR� Note that depending on the
current menu location, the Return Button
require multiple pushes to allow access to the Main
Menu of the DVDR�
2� Use the Up and Down Arrow Buttons
"Video
DVD" and press the Enter Button
3� Use the Up and Down Arrow Buttons
"Video In" and press the Enter Button
Auto Chapter Setting
If the Auto Chapter setting is OFF, the DVDR will start
a new chapter each time the recording is paused� To
turn the Auto Chapter setting OFF, perform the following
functions:
1� Press the Return Button
Menu of the DVDR� Note that depending on the
current menu location, the Return Button
require multiple pushes to allow access to the Main
Menu of the DVDR�
2� Use the Up and Down Arrow Buttons
"Setup" and press the Enter Button
3� Use the Up and Down Arrow Buttons
"Auto Chapter" and press the Enter Button
4� Use the Up and Down Arrow Buttons
"OFF" and press the Enter Button
Alternatively, Auto Chapter can be set to start a new
chapter after every 5 minutes, 10 minutes, or 15 minutes
of recording� Use the Up and Down Arrow Buttons
highlight a time interval within the Auto Chapter Menu
and press the Enter Button
NTSC/PAL Video Setting
The DVDPak2 supports both NTSC and PAL video
settings� The DVDPak2 will not record if the video setting
conflicts with the disc format� Change the video setting
by performing the following functions:
1� Press the Return Button
Menu of the DVDR� Note that depending on the
current menu location, the Return Button
require multiple pushes to allow access to the Main
Menu of the DVDR�
to access the Main
may
to highlight
�
to highlight
�
to access the Main
may
to highlight
�
to highlight
�
to highlight
�
to
�
to access the Main
may
2� Use the Up and Down Arrow Buttons
"Setup" and press the Enter Button
3� Use the Up and Down Arrow Buttons
"Color System" and press the Enter Button
4� Use the Up and Down Arrow Buttons
either PAL or NTSC and press the Enter Button
Units Setting
If connected to a SeeSnake Reel that contains the
CountPlus cable-measurement system, the DVDPak2
will display the distance in either meters or feet� If set
to "Auto" the DVDPak2 will automatically display the
cable-measurement in meters if PAL is set and in feet
if NTSC if set�
To change the cable-measurement units, perform the
following functions:
1� Press the Menu Key
2� Use the Down Arrow Key
press the Select Key
meters, and auto�
3� Press the Menu Key
Color, Contrast, and Brightness Settings
To adjust the color, contrast, or brightness settings as
viewed by the camera on the DVDPak2, perform the
following functions:
1� Press the Menu Key
2� Use the Up and Down Arrow Keys
down and highlight "Color," "Contrast," or "Bright-
ness" and use the Left and Right Arrow Keys
make adjustments� A status bar will appear on the
screen to visually represent the color adjustments�
3� Press the Menu Key
Camera LEDs Brightness Setting
To change the brightness of the LEDs on the camera
head, push the Brightness Key
Right Arrow Keys
to adjust the brightness� Press
the Menu Key
to close the menu�
Alternatively, push the Brightness Key
to first increase and then decrease the brightness of the
LEDs on the camera head�
Zero-point Setting
If using a SeeSnake Reel equipped with the CountPlus
cable-measurement counter, the cable-measurement
will appear on the monitor of the DVDPak2� To set an
interim zero-point while using the CountPlus, press the
2
to highlight
�
to highlight
�
to highlight
�
to highlight "Unit" and
to toggle between feet,
to close the menu�
on the DVDPak2 Keypad�
to scroll
to close the menu
and use the Left and
multiple times
English - 11
�
to
Advertisement
Table of Contents
