Table of Contents
Advertisement
Position 'High' (65 mm): Cutting height setting is used when you lawn
has excessive growth such as following holidays or first cut of the season.
v Move both axles to the desired position in the E-Gate. Make sure that
both sides of the axle are in the same position. Make sure that both
axles are in the same position.
Only for 340 Li (in 5 positions) [ Fig. O8 ]:
The cutting height can be adjusted from 20 – 60 mm (from rear to front).
Position 1 (20mm): Cutting height setting should only be used on well
maintained 'manicured lawns' without excessive moss or thatch.
Position 2 (30 mm): Cutting height setting is the suitable for most lawns.
Position 3 (40 mm): Cutting height setting is the suitable for most lawns.
Position 4 (50 mm): Cutting height setting is the suitable for most lawns.
Position 5 (60 mm): Cutting height setting is used when you lawn has
excessive growth such as following holidays or first cut of the season.
1. Pull the lever to the wheel.
2. Move the lever to the desired position.
3. Release the lever and let it engage.
To start the mower [ Fig. O9 / O10 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example
do not attach the start lever to the handle.
To start:
The product is provided with a two-switch safety device (safety key
with starting lockout) to prevent the product from being turned on
by accident.
There are two start levers. Either one has to be used to start.
1. Open the battery cover.
2. Put the batteries into the battery holders until they audibly engages.
3. Put the safety key into the mower and turn it to position I.
4. Push the starting lockout with one hand and pull the start lever with
the other hand.
The mower starts.
5. Release the starting lockout.
Only for 340 Li [ Fig. O11 ]: The level indicator opens during
mowing. When it closes during mowing, the grass box is full
and must be emptied.
To stop:
1. Release the start lever.
The mower stops.
2. Turn the safety key to position 0 and remove it.
Tips to use the mower:
If grass residue is left in the discharge opening, pull the mower backwards
about 1 m so that the grass residue can drop out downwards.
To produce a well-maintained lawn and optimise the cutting performance,
we recommend to cut the lawn regularly once a week if possible. The lawn
becomes denser if you cut it frequently.
After relatively long cutting intervals (holiday lawn), first of all cut in one
direction with the highest cutting height and then cut in the crosswise
direction with the required cutting height.
If possible, only cut the grass when it is dry, if the grass is damp, the
cutting pattern will be uneven.
Cutting performance and battery charge:
The lawn area which can be cut on each battery charge depends on
several factors such as moisture, grass density and cutting height. In order
to ensure an optimal use of space, do not turn the mower on and off too
frequently as this severely reduces the battery running time. The cutting
performance for each battery charge can be ideally utilised by increasing
the cutting height and frequent mowing.
Transport position [ Fig. O12 ]:
The easy transport position provides additional mobility due to its upright
driving position. Easy to get on and off the lawn at any distance.
1. Attach the grass box to the switch box (see 5. STORAGE).
2. Pull the mower to and from the lawn when it is set in the storage
position.
6
22301-85.960.01.indd 6
22301-85.960.01.indd 6
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery, remove the
safety key and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside, the blade and the discharge opening
with a brush (do not use sharp objects).
To clean the overside of the mower and the grass box:
1. Clean the overside with a damp cloth.
2. Clean the airflow slots and the grass box with a soft brush
(do not use sharp objects).
To clean the battery and the battery charger:
Make sure that the surface and the contacts of the battery and the battery
charger always are clean and dry before you connect the battery charger.
Do not use running water.
v Clean the contacts and the plastic parts with a soft and dry cloth.
5. STORAGE
To put into storage [ Fig. O9 ]:
The product must be stored away from children.
1. Turn the safety key to position 0 and remove it.
2. Remove the battery.
3. Charge the battery.
4. Clean the mower, the battery and the battery charger
(see 4. MAINTENANCE).
5. Store the mower, the battery and the battery charger in a dry,
enclosed and frost-free place.
Storage position [ Fig. S1 ]:
1. Remove the grass box.
2. Set on the highest cutting height.
3. Fold the handle flat and lock it in position 4.
4. Stand the mower upright.
5. Make sure that the grass box is completely empty.
6. Attach the grass box to the switch box with the storage hook.
Make sure that the grass box is completely secured, the storage
function is accomplished.
7. Store the mower in upright position.
Disposal:
(in accordance with RL2012/19/EC / S.I. 2013 No. 3113)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.
Disposal of the battery:
The FLYMO battery contains lithium-ion cells that should not
be disposed of with normal household waste at the end of its
life.
Li-ion
25.10.21 14:12
25.10.21 14:12
Advertisement
Table of Contents
