Resetting The Remote - Harman Kardon AVR 7200 Owner's Manual

CONFIGURING THE REMOTE
Navigation Button n until RENAME appears
on the bottom line of the LCD screen, as shown in
Figure 66.
3. At the next menu screen press the
Navigation Button n until RENAME KEY
appears on the bottom line of the LCD screen, as
shown in Figure 69. Press the Set Button F to
continue.
R E N A M E
R E N A M E K E Y
Figure 69
4. The next display screen (Figure 70) is where
you select the device within which the key to be
renamed exists. Press the Navigation
⁄ / ¤
Button n until the name of the base device
appears. In our example, since we want to rename
a button within the DVD device memory, DVD
should appear in the lower line of the LCD. When
the desired device name appears, press the Set
Button F.
S E L E C T A D E V I C E
D V D
Figure 70
5. At the next menu screen you will select the first
button within the device to be renamed, as
instructed in the display shown in Figure 71. Select
the button by simply pressing it on the remote.
S E L E C T A K E Y
Figure 71
6. Depending on whether or not the button pressed
already has a named function within the device
selected, one of two things will happen.
a. If the button to be renamed already has a pre-
programmed, or previously renamed title in the
remote's memory, you will see that name on the
top line of the LCD display, and a blinking block
cursor will appear on the far left side of the bot-
tom line of the display, as shown in Figure 72.
b. If the button to be renamed does not have a
function in the device selected, the top line of
the LCD screen will be blank, and a blinking
block cursor will appear on the far left side
of the bottom line of the display, as shown in
Figure 73.
D I S C S K I P
Figure 72
Figure 73
46 CONFIGURING THE REMOTE
7. To enter the new name for the key, press the
Numeric Keys A. The letters above the
numbered buttons indicate which letters or sym-
bols will appear when the button is pressed during
⁄ / ¤
the renaming process. The first press of the button
will enter the first character shown, subsequent
presses of the same button will change the display
to the other letters above that numbered key. For
example, since the first letter we need to rename
the Tone button to Zoom is a "Z," so you would
locate the "Z" above the "9" button, and press the
button four times. The first press shows a "W," the
subsequent presses step through the other letters
available until the "Z" appears. Consult the table on
this page to see which characters are available by
pressing a particular button.
8. After you enter the first letter of the new device
name, there are three options for entering the
next character:
a. To enter a letter that requires a different numeric
key to be pressed, simply press that button. The
cursor will automatically move to the next posi-
tion and the first letter accessed by the new but-
ton will appear. Following our example, the next
letter needed is an "O," so you would press the
"6" button once.
b. To enter a letter that uses the same numeric
key, you must first press the
Button D to move the blinking cursor block
to the next position. Then press the Numeric
Key A as required to enter the desired letter.
This is the way you would enter the second "O"
in the word ZOOM, and again for the letter "M. "
c. To enter a blank space, press the
Button D twice. The first press will move the
cursor to the right, and the second press will
move the cursor one more space to the right,
leaving a blank space between the last letter and
the next one.
9. Repeat Steps 7 and 8 as needed to complete
entering the needed letters, numbers, characters
and spaces.
10. When the text entry is complete, press the Set
Button F. The new name will be entered into
the remote's memory, replacing the default name.
11. At this point you have two options:
a. If you wish to program an additional key within
the same device, press the Set Button F as
instructed by the bottom line of the LCD display
reading ANOTHER KEY. The remote will
return to the SELECT A KEY menu option as
shown in Step 6. Repeat the instructions in
Steps 6 though 11 to rename the next key.
b. If you have no additional keys to rename, press
the
⁄
the menu screen displays EXIT on the bottom
line of the display. Press the Set Button F to
return the remote to normal operation.
NOTES ON RENAMING KEYS:
• Renaming a key does not change its function. You
may change the function of an individual key by
learning a new code into the remote. See page 39
for more information.
• When a key is renamed it will only apply to the
specific device selected in Step 4. The same key
may be renamed as needed for each individual
device with which it is used.

Resetting the Remote

Depending on the way in which the remote has been
programmed, there may be a situation where you wish
to totally erase all changes that have been made to the
remote and return it to the factory defaults. You may do
that by following the steps shown below, but remember
that once the remote is reset, ALL changes that have
been made, including programming for use with other
devices, learned keys, macros, punch-through settings
and key names, will be erased and any settings you
› Navigation
had previously made will have to be reentered.
To erase all settings and reset the remote to the
original factory default settings and displays, follow
these steps:
1. Press and hold the Program Button O for
about three seconds while the message shown
› Navigation
in Figure 15 appears in the remote's LCD
Information Display 2. Release the button
when the red light under the Set Button F
appears.
2. The remote's MAIN MENU message (Figure 16),
will appear in the LCD display and the Set Button
F will remain illuminated in red. Press the
Navigation Button n until USER RESET
appears on the bottom line of the LCD screen, as
shown in Figure 74.
M A I N M E N U
U S E R R E S E T
Figure 74
3. Press the Set Button F to reset the remote.
Note that once the Set Button is pressed the
process may not be stopped. While the remote's
memory is being cleared a RESETTING... mes-
sage will appear in the upper line of the remote's
LCD screen as shown in Figure 75. It may take a
Navigation Button D once so that
⁄ / ¤