Register Online - DeWalt DCV581HAM Instruction Manual

Cord, Hose and Accessory Storage (Fig. A)
When the vacuum is not in use, the power cord should
be secured around the vacuum handle underneath the
cord wrap 10 . The vacuum hose can be wrapped around
appliance, underneath the battery interface, and secured
with the hose clip 7 also located at the back of the vacuum.
The two accessories (crevice tool and wide nozzle) can be
stored on board the vacuum as well.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
The DCV581h includes a 1-1/4" hose, crevice tool (stored in
the handle) and wide nozzle.
A replacement filter is available at extra cost at your local
D WALT service center.
e
Dust Collector (Fig. G)
In the vacuum mode, the appliance can also function as a
dust collector for power tool applications producing dust
or debris.
Install the DWV9000 dust extraction adaptor, availiable at
additional cost, to facilitate connection of a power tool to
the vacuum hose 2 .
nOTE: Follow these instructions in reverse to set up the
appliance for standard vacuum use.
iMPORTAnT! The DWV9000 dust
extraction adaptor is designed to work
with Dust System Compatible D
power tools. An additional adaptor will
be necessary for use with incompatible
D
Repairs
The charger and battery pack are not serviceable.

WALT
e
WALT Industrial
e

Register Online

Thank you for your purchase. Register your product now for:
•
•
•
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
Fig. G
2
1. Unscrew and remove the standard hose nozzle.
2. Screw on the dust extraction adaptor to the hose.
3. Attach the adaptor to the power tool.
WALT tools.
e
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
Always use identical replacement parts.
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
WALT will repair, without charge, any defects due to
e
English
WALT
e
WALT factory
e
WALT authorized service center.
e
WALT (1-800-
e
9