Transport Control Punch-Through; Reassigning Device Control Selectors; Resetting The Remote Memory - Harman Kardon AVR 220 Owner's Manual

Programming the Remote
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown above.
However, press the VID1/VCR Input Selector
in Steps 1 and 3.

Transport Control Punch-Through

The AVR 220's remote may be programmed to
operate so that the Transport Control
Functions (Play, Stop, Fast Forward, Rewind,
Pause and Record) for a VCR, cassette deck, DVD
or CD will operate in conjunction with one of the
other devices controlled by the remote. For exam-
ple, while using and controlling the TV, you may
wish to start or stop your VCR or DVD without
having to change the device selected by the
AVR 220 or the remote. To program the remote for
Transport Control Punch-Through, follow these
steps:
1. Press the Input Selector for the device
you will be using (e.g., TV) when you wish to
have Transport Control Punch-Through active
and the Mute Button at the same time
38
until the red light appears under the Input
Selector and the Program/SPL
Indicator flashes amber.
2. Press the Play Button . The Program/SPL
Indicator will stop flashing and
stay amber.
3. Press and release the Input Selector Button
for the device whose transport mechanism
will be controlled (e.g., DVD, CD). The
Program/SPL Indicator will blink green
three times and then go out to confirm the
data entry.
Example: To control the transport of a DVD
player while the remote is set to control the TV,
first press the VID2/TV Input Selector
Button and the Mute Button
the same time. Next, release them and press
the Play Button , followed by the DVD
Input Selector Button .
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown iabove.
However, press the VID2/TV Input Selector in
Steps 1 and 3.
36 PROGRAMMING THE REMOTE
Reassigning Device Control
Selectors
Although each Input Selector
assigned to the category of product shown on the
remote, it is possible to reassign one of these but-
tons to operate a second device of another type.
For example, if you have two VCRs but no satellite
receiver, you may program the "SAT" button to
operate a second VCR. Before following the nor-
mal programming steps for either Three-Digit entry
or Auto Search code entry, you must first reassign
the button with the following steps:
1. Press the Input Selector
reassign and the Mute Button
same time until the red light appears under the
Input Selector
Indicator flashes amber.
2. Press the Input Selector
type you wish to program into the reassigned
button.
3. Enter the three-digit code for the specific
model you wish the reassigned button to
operate.
4. Press the same Input Selector
Step 1 once again to store the selection. The
red LED under the reassigned Input Selector will
flash three times and then go out.
Example: To use the CBL/SAT button to oper-
ate a second VCR, first press the CBL/SAT
Input Selector
38
at the same time until the red light glows
under the CBL/SAT
button, followed by the three-digit code
for the specific model you wish to control.
Finally, press the CBL/SAT

Resetting the Remote Memory

at
38
As you add components to your home theater
system, occasionally you may wish to totally repro-
gram the remote control without the confusion of
any commands, macros or "Punch-Through" pro-
gramming that you may have done. To do this, it is
possible to reset the remote to the original factory
defaults and command codes by following these
steps. Note, however, that once the remote is
reset, all commands or codes that you have
entered will be erased and will need to be
reentered:
1. Press any of the Input Selector Buttons
and the "O" Button
until the Program/SPL Indicator
to flash amber.
is normally
2. Press the "3" Button
3. The red LED under the Input Selector
go out and the Program/SPL Indicator
will stop flashing and turn green.
4. The Program/SPL Indicator
green until the remote is reset. Note that this
may take a while, depending on how many
commands are in the memory and need to be
you wish to
erased.
38 at the
5. When the Program/SPL Indicator
and the Program/ SPL out, the remote has been reset to the factory
settings.
for the device
pressed in
and the Mute Button
button. Press the VCR
button again.
at the same time
begins
three times.
will
will remain
goes