AVR225 A/V DOLBY DIGITAL RECEIVER SERVICE MANUAL CONTENTS ESD WARNING………………………….…….2 AMPLIFIER BIAS ADJUSTMENT……...…21 LEAKAGE TESTING………………..……..3 TECH TIP HKTT2004-03………………….22 BASIC SPECIFICATIONS…………….….…..4 TECH TIP HKTT2003-01………………….26 FRONT PANEL CONTROLS………………...5 BLOCK DIAGRAM………………………….27 FRONT PANEL DISPLAY…………………….7 IC PINOUTS……………………………..….28 REAR PANEL CONNECTIONS……..….……9 TRANSISTOR PINOUTS………..…..…….64 REMOTE CONTROL FUNCTIONS……..…..11 ELECTRICAL PARTS LIST………..…..….65...
AVR225 Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor "chip" components.
AVR225 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester...
All features and specifications are subject to change without notice. * See the following trademark acknowledgements: Harman Kardon and Power for the Digital Revolution are registered trademarks of Harman Kardon, Inc. is a trademark of Harman International Industries, Inc. (patent no. 5,386,478).
AVR225 FRONT-PANEL CONTROLS ı Û Ò Ô ˆ Ù Ú AVR 225 Ó AM/FM Tun Mode & 1 Main Power Switch ! Input Source Selector Ô Set Button 2 System Power Control @ Tuning Mode Selector Input Indicators...
Page 6
AVR225 FRONT-PANEL CONTROLS between the Optical #e and Coaxial $b of input, some modes are not always available. (See plastic cap installed to avoid dust contamination that page 25 for more information about surround modes.) might degrade future performance.
AVR225 FRONT-PANEL INFORMATION DISPLAY Q PO OPT 123 COAX 123 ANALOG AUTO TUNED ST PRESET SLEEP NIGHT PL II OSD DSP VMAx NF LOGIC 7 CM E F G H A Bitstream Indicators I Logic 7 Mode Indicators Q Tuned Indicator...
Page 8
AVR225 FRONT-PANEL INFORMATION DISPLAY N Sleep Indicator: This indicator lights when the Sleep function is in use. The numbers in the Preset Number/Sleep Timer J will show the minutes remaining before the AVR 225 goes into the Standby mode. (See page 24 for more information on the Sleep function.)
Connect this jack to the “IR IN” jack to the positive (+) terminal on the right front speaker on Harman Kardon (or other compatible) equipment. and the green terminal to the positive (+) terminal on ¢ Tape Outputs: Connect these jacks to the the center front speaker.
Page 10
AVR225 REAR-PANEL CONNECTIONS b Coaxial Digital Audio Inputs: Connect the coax CEA specifications, while existing speakers typically Video 1 Audio Inputs: Connect these jacks to use a red terminal for the positive (+) speaker wire digital audio output from a DVD player, HDTV receiver, the PLAY/OUT audio jacks on a VCR or other video connection.
AVR225 REMOTE CONTROL FUNCTIONS a Power Off Button b IR Transmitter Window c Program/SPL Indicator d Power On Button e Input Selectors f AVR Selector g AM/FM Tuner Select h Test Button i Sleep Button j Surround Mode Selector...
Page 12
Harman Kardon CD or DVD players and cassette between the AM and FM bands. levels. When changing an item such as the surround decks.
Page 13
AVR225 REMOTE CONTROL FUNCTIONS weak will change to monaural reception. (See page Clear Button: Press this button to clear incorrect SPL Button: This button activates the AVR 225’s 28 for more information.) entries when using the remote to directly enter a radio EzSet function to quickly and accurately calibrate the station’s frequency.
AVR225 INSTALLATION AND CONNECTIONS System Installation cable TV system. Note that if the antenna or connec- Front Left = White Front Right = Red After unpacking the unit, and placing it on a solid surface tion uses 300-ohm twin-lead cable, you must use the...
Page 15
AVR225 INSTALLATION AND CONNECTIONS 2. Connect the analog audio and video outputs of a Power Connections television set or any other video source to the Video 2 Input Jacks f This unit is equipped with two accessory AC outlets.
• Amplifier is in protection mode • Contact your local Harman Kardon service center, which you can due to internal problems locate by visiting our Web site at www.harmankardon.com No sound from surround or •...
AVR225 AVR125/225 DISASSEMBLY PROCEDURE <1> TOP-CABINET(21) REMOVAL 1. Remove 13 screws(S1,S7) and then remove the Top-cabinet. <2> FRONT PANEL ASS’Y REMOVAL 1. Remove the Top-cabinet, referring to the previous step<1>. 2. Disconnect the connect (BN72-Card canle)) on the FP PCB(37-1) from connector(CN72) on the Input PCB(39-1) 3.
Page 19
AVR225 <7>TUNER MODULE(40) REMOVAL 1. Remove the Top-cabinet, referring to the previous step<1>. 2. Disconnect the connector(CON1-Card cable) from connector(CN13) on the Input PCB ASS’Y(39-1). 3. Remove 2 screws(S8) and then remove the Tuner Module(40). <8>VIDEO PCB(39-2) REMOVAL 1. Remove the Top-cabinet, referring to the previous step<1>.
Page 20
AVR225 DISASSEMBLY 1) REMOVAL OF TOP COVER 2) REMOVAL OF FRONT PANEL 3) PRINCIPAL PARTS LOACTION TUNER MODULE INPUT PCB TRANS FORMER MAIN PCB FRONT PCB...
AVR225 AMPLIFIER SECTION BIAS ADJUSTMENT Measurement condition . No input signal or volume position is minimum. Standard value. ± . Ideal current = 48mA ( ± . Ideal DC Voltage = 21.12mV ( CUP11517X (MAIN PCB) CN63 CN61 CN62...
AVR210 AVR310 audio problems in an AVR receiver. Use the following AVR220 AVR320 procedures to help find what is working, then to quickly locate the problem area. AVR520 AVR225 AVR125 AVR525 Equipment needed: AVR130 AVR230 1 set of (RCA) Y adaptors.
Page 23
Isolating audio problems in an AVR receiver Using 6/8 Direct In At this point you will be able to check and assure all output levels are the same. 10) IF THE OUTPUT LEVELS ARE NOT THE SAME STOP! Go no further. At this point you will need to use the charts to see where you are losing your signal.
TECH TIPS harman/kardon Troubleshooting tips and solutions to common service problems For models: TIP# HKTT2003-01 Rev5 AVR7000/7200/7300/8000 AVR10 AVR100/200/300/500 DPR1001 AVR110/210/310/510 DPR1005 AVR120/220/320/520 DPR2005 AVR125/225/325/525 HK3370/3470/3375/3475 HK3250 AVR130/230/330/430/630 AVR135/235/335/435/635 Subject: Backup Memory on AVR/DPR/HK series receivers In the event of the complaint: “the receiver is losing its memory (any programmed system settings) when the unit is turned off, or after the unit is unplugged (briefly*)”: Check and replace: Model...
AVR225 CMOS IC LC74763, 74763M On-Screen Display LSI Preliminary Overview Package Dimensions The LC74763 and LC74763M are on-screen display unit: mm CMOS LSIs that superimpose text and low-level 3196-DIP30SD graphics onto a TV screen (video signal) under the [LC74763] control of a microcontroller.
Page 29
AVR225 LC74763, 74763M Pin Functions Pin No. Symbol Function Description Ground Ground connection Xtal Connection for the crystal and capacitor used to form the crystal oscillator that generates Crystal oscillator connection the internal synchronization signal. The oscillator can be selected with a command switch.
Page 40
AVR225 PIN ASSIGNMENT (TOP VIEW) Top view...
Page 41
AVR225 BLOCK DIAGRAM VFD DRIVER IC PIN FUNCTION (LC75725E) : IC74 Pin No. Function Handling when unused 1, 13 Driver block power supply connection. (Both pins must be connected.) — — Logic block power supply connection. Provide a voltage between 4.5 and 5.5 V.
Page 43
AVR225 M-COM IC PIN ASSIGNMENT & BLOCK DIAGRAM PIN ASSIGNMENT (TOP VIEW) P 20/A16 P 21/A17 P22/A18 P57/CLK P23/A19 RSTX P24/A20/PPG0 P56/RDY P 25/A21/PPG1 P55/HAKX P26/A22/PPG2 P54/HRQ P27 /A23/PPG3 P53/WRHX P30 /A00/AIN0 P52/WRLX P 31/A01/BIN0 P51/RDX P50/ALE P32/A02/ZIN0 PA3/OUT3...
Page 44
AVR225 IC PIN FUNCTION (M-COM : MB90F476APFG) : IC72 LQFP Pin Name Circuit Type Function Oscillator pin Oscillator pin 32 kMHz Oscillator pin 32 kMHz Oscillator pin RSTX Reset input pin General-purpose I/O ports P00 to P07 A pull-up resistor can be attached using the pull-up resistor setting register (RDR0) (RD07 to RD00 = 1).
Page 45
AVR225 LQFP Pin Name Circuit Type Function General-purpose I/O ports In the external bus mode, the pin functions as an external address pin. (CMOS/H) AIN0 The pin is an 8-/16-bit up-and-down timer input pin (ch0). General-purpose I/O port In the external bus mode, the pin functions as an external address pin.
Page 46
AVR225 LQFP Pin Name Circuit Type Function General-purpose I/O port In the external bus mode, the pin functions as ALE pin. (CMOS) In the external bus mode, the pin functions as an address capture enable signal (ALE) pin. General-purpose I/O port In the external bus mode, the pin functions as the RDX pin.
Page 47
AVR225 LQFP Pin Name Circuit Type Function General-purpose I/O port SOT0 (CMOS) The pin functions as an UART data output pin. General-purpose I/O port SCK0 (CMOS/H) The pin functions as an UART clock I/O pin. General-purpose I/O port TIN0 (CMOS/H) The pin functions as the event input pin of the 16-bit reload timer.
November 1988 Revised November 1999 74AC04 • 74ACT04 Hex Inverter General Description Features The AC/ACT04 contains six inverters. reduced by 50% on 74AC only Outputs source/sink 24 mA ACT04 has TTL-compatible inputs Ordering Code: Order Number Package Number Package Description 74AC04SC M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-120, 0.150”...
Page 52
AVR225 PIN ASSIGNMENT (74HCU04AFN : IC71,72 ) LOGIC SYMBOL (10) (11) (13) (12) TRUTH TABLE...
Page 55
AVR225 DIR IC PIN FUNCTION (AK4114VQ) : IC75 PIN/FUNCTION Pin Name Function IPS0 Input Channel Select 0 Pin in Parallel Mode Receiver Channel 4 Pin in Serial Mode (Internal biased pin) No Connect NC(AVSS) No internal bonding. This pin should be connected to AVSS.
Page 56
AVR225 PIN/FUNCTION (Continued) Pin Name Function Power-Down Mode Pin When “L”, the AK4114 is powered-down and reset. Master Clock Operation Mode 0 Pin in Parallel Mode CDTO Control Data Output Pin in Serial Mode, IIC= “L”. CAD1 Chip Address 1 Pin in Serial Mode, IIC= “H”.
Page 57
AVR225 n Block Diagram DZFL1 AK4356 Audio LOUT1+ DATT LOUT1- MCLK MCKO DZFR1 LRCK Controller LRCK ROUT1+ DATT BICK ROUT1- BICK DZFL2 LOUT2+ DATT Control LOUT2- CCLK Register DZFR2 CDTI ROUT2+ DATT ROUT2- DZFL3 LRCK LOUT3+ DATT LOUT3- BICK...
Page 62
AVR225 A/D CONVERTER IC PIN FUNCTION (AK5380VT) : IC77 PIN/FUNCTION Pin Name Description AINR Rch Analog Input Pin AINL Lch Analog Input Pin NC Pin No internal bonding. VCOM Common Voltage Output Pin Normally connected to AGND with a 0.1 F ceramic capacitor in parallel with an electrolytic capacitor less than 2.2 F.
AVR225 AVR225 ELECTRICAL PARTS LIST Reference Designator Part Number Description PCB , FRONT Capacitors C703 HCBS1H821KBT CAP , CERAMIC 820PF 50V K C704,735,773,774,777,778,864 HCEA1VH100T CAP , ELECT 10UF 35V C712 HCEA1HH1R0T CAP , ELECT 1UF 50V C713,730,732,736,770,771,805, HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z...
Page 68
AVR225 Reference Designator Part Number Description C901,998 CCFT1H104ZF CAP , SEMI 0.1UF 50V ZF C905,908,923,925,963,999 CCKT1H223ZF CAP , CERAMIC 0.022UF 50V ZF C911 HCEA1CH471T CAP , ELECT 470UF 16V C912 HCEA1CH221T CAP , ELECT 220UF 16V C922,924,962 HCEA1EH101T CAP , ELECT...
Page 69
AVR225 Reference Designator Part Number Description R531~540 CRD20TJ221T RES , CARBON 220 OHM 1/5W J R541~545,630 CRD20TJ271T RES , CARBON 270 OHM 1/5W J R556~560,962 CRD20TJ273T RES , CARBON 27K OHM 1/5W J R561~565 CRD20TJ162T RES , CARBON R566~575,581~600,987...
Page 70
AVR225 Reference Designator Part Number Description PCB , INPUT Capacitors C201~224,321,322,325,326 CCKT1H221KB CAP , CERAMIC 220PF 50V KB C231,232,349,350,799,382~386, 390,421,424,426,440,447,452, HCEA1CH101T CAP , ELECT 100UF 16V 454,456, 708,709,712, 728,731,733,752,754,780,783, C233~236 HCEA1CKS101T CAP , ELECT 100UF 16V C237,240,359,361,362,387,703, CCKT1H181KB CAP , CERAMIC...
Page 71
AVR225 Reference Designator Part Number Description C715,782 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z C722,723 CCCT1H100DC CAP , CERAMIC 10PF 50V DC C724 HCBS1H330JT CAP , CERAMIC C565,566,725 CCCT1H330JC CAP , CERAMIC 33PF 50V JC C392,741,742 HCEA1EH470T CAP , ELECT...
Page 72
AVR225 Reference Designator Part Number Description IC75 HVIAK4114VQ IC , DIR IC77 HVIAK5380VT I.C 2CH AUDIO ADC IC78 HVIAK4356VQ I.C , D/A CONVERTER IC79 HVICS493263-CLG I.C , DSP CS493263-CLG HC3990509F I.C. REGULATOR NJM7905FA IC95 Resistors R201~223,477,720,771 CRD20TJ471T RES , CARBON...
Page 73
AVR225 Reference Designator Part Number Description R433,466,469,906 CRD20TJ100T RES , CARBON 10 OHM 1/5W J R480,481,560 CRD20TJ682T RES , CARBON 6.8K OHM 1/5W J R551,552 CRD20TJ181T RES , CARBON 180 OHM 1/5W J R556 CRD20TJ822T RES , CARBON 8.2K OHM 1/5W J...