Table of Contents
Advertisement
Additional information
Symptom
The System Setup screen
doesn't appear (or is displayed
incorrectly).
Can't record video.
Settings
Symptom
The Auto MCACC Setup
continually shows an error.
After using the Auto MCACC
Setup, the speaker size setting
(LARGE or SMALL) is incorrect.
The display shows KEY LOCK
ON when you try to make
settings.
12V TRG ERR blinks in the
display.
Display
Symptom
The display is dark or off.
After making an adjustment the
display goes off.
You can't get DIGITAL to display
when using the SIGNAL SELECT
button.
The Dolby/DTS indicator doesn't
light when playing Dolby/DTS
software.
When playing a DVD-Audio disc,
the DVD player display shows 96
kHz. However, the receiver's
display does not.
During playback of a DTS 96/24
source, the display doesn't show
96kHz.
Cause
• Some TVs connected to the receiver with
component video cables do not display the
System Setup screen when the Color Burst
feature is on.
• The MONITOR OUT jack hasn't been
connected.
• You connected your TV to the MULTI ROOM
& SOURCE MONITOR OUT jack instead of
the main MONITOR OUT jack.
• VSX-1014-S model only – The TV format
setting for your country or region is incorrect.
• You are trying to record a source connected
to the component video jacks.
• The source is copy protected.
• The recorder's video input is hooked up
using a different type of cable to the source
video output.
Cause
• The ambient noise level in the room is too
high, or obstacles are blocking the setup
microphone.
• There was some inaudible low-frequency
noise in the room.
• Your Pioneer dealer has enabled the key
lock feature.
• There is a problem with the 12V trigger
connection.
Cause
• The display is set to dark or off.
• The display is set to off.
• There is a problem with the digital
connections or the digital input is assigned
incorrectly.
• The multichannel analog inputs are
selected.
• The player is paused.
• The player's sound output settings are
wrong.
• The audio from these discs is output from
the analog audio jacks of the DVD player only;
the receiver does not show the sampling rate
of the input signal through the analog inputs.
• The receiver's input signal type is set to
analog.
Remedy
• When the receiver is in standby, switch to COLOR
BURST OFF by holding down the front panel ACOUSTIC
EQ button and pressing
STANDBY/ON. (the current
setting appears in the display).
• Connect the MONITOR OUT jack to the TV monitor (see
Connecting video components on page 18).
• See Changing the TV format setting on page 76 to
change the format setting to match your country or
region.
• Connect the source component to either the composite
video or the S-video jacks (see Connecting video
components on page 18).
• You can't record sources that have been copy protected.
• Hook up the source and the recorder using the same
type of video cable (VSX-2014i-G model only – see About the
video converter on page 15 for exceptions to this).
Remedy
• Keep the noise level in the room as low as possible
when using the Auto MCACC Setup (see Other problems
when using the Auto MCACC Setup on page 13 for more
on this). If the noise cannot be kept low enough, you will
have to set up the surround sound manually (page 43).
• The low-frequency noise could have been caused by an
air conditioner or motor. Switch off all appliances in the
room and rerun the Auto MCACC Setup.
• Ask your Pioneer dealer to disable the key lock.
• Turn the receiver off and check the 12V trigger
connection.
Remedy
• Press FL. DIMMER on the remote control repeatedly to
select a different brightness.
• Press FL. DIMMER on the remote control repeatedly to
select a different brightness.
• Check your digital connections and/or assign the digital
inputs correctly (see Assigning the digital inputs on
page 63).
• Press MULTI CH IN again (see Selecting the
multichannel analog inputs on page 37).
• Press play.
• Set the player correctly (consult the manual that came
with the player, if necessary).
• This is not a malfunction. See also the operating
instructions that came with your DVD player.
• Set the receiver to AUTO or DIGITAL (see Choosing the
input signal on page 33).
12
73
En
Advertisement
Table of Contents
