Chimney Components - Heatilator HST-42D Owner's Manual

B. Chimney Components
The following pictures show only those chimney compo-
nents which may be safely used with this fireplace.
Catalog #
CAK4A Chimney Air Kit
ID4 Insulated Duct/Outside Air
UD4 Uninsulated Duct/Outside Air
SL306 Chimney Section - 6 in. (152 mm) long
SL312 Chimney Section - 12 in. (305 mm) long
SL318 Chimney Section - 18 in. (457 mm) long
SL324 Chimney Section - 24 in. (610 mm) long
SL336 Chimney Section - 36 in. (914 mm) long
SL348 Chimney Section - 48 in. (1219 mm) long
SL3 Chimney Stabilizer
SL315 Chimney Offset/Return - 15 deg
SL330 Chimney Offset/Return - 30 deg
FS338 Ceiling Firestop - Straight
FS339 Ceiling Firestop - 15 deg
FS340 Ceiling Firestop - 30 deg
AS8 SL300 Straight Attic Insulation Shield, 24 in. (610 mm)
JB877 Chimney Joint Band
CB876 Chimney Bracket
RF370 Roof Flashing - Flat to 6/12 Pitch
RF371 Roof Flashing - 6/12 to 12/12 Pitch
TR344 Round Termination Cap
TR342 Round Telescoping Termination Cap
ST375 Square Termination Cap
TS345 Square Termination Cap
TS345P Square Termination Cap - Painted
TCT375 Terra Cotta Termination Cap
DTO134 Short Octagon Decorative Cap
DTO146 Tall Octagon Decorative Cap
DTS134 Short Square Decorative Cap
DTS146 Tall Square Decorative Cap
CT35 Chase Top
LDS33 Decorative Shroud - 3 ft x 3 ft (.91 m x .91 m)
LDS46 Decorative Shroud - 4 ft x 6 ft (1.22 m x 1.83 m)
LDS-BV Decorative Shroud - 26 in. x 26 in. (660 mm x 660 mm)
Field Constructed Shrouds (See "Woodburning Termination
Cap")
CT-3A Adapter - May be used with the following copper caps
CT-Series
DT-Series
44
Description
Heat & Glo • HST-42D • 27177 • Rev AF • 1/11
12 in.
(305 mm)
5-1/4 in.
(133 mm)
10-1/2 in.
(287 mm)
CAK4A Chimney Air Kit
ID4 Insulated Duct
42 in.
(1067 mm)
UD4 Uninsulated Duct
42 in.
(1067 mm)
8 in.
(203 mm)
Chimney Sections
C a t a l o g #
in
SL306 6
SL312 1 2
SL318 1 8
SL324 2 4
SL336 3 6
SL348 4 8
A = Actual Length
B = Effective Length (length of
chimney part after it has
been snapped to another)
20-3/4 in.
(527 mm)
4-3/4 in. (121 mm)
Effective Height
SL3 Vent Stabilizer
12 in.
(305 mm)
4 in. (102 mm)
4 in. (102 mm) i.d.
4 in. (102 mm) i.d.
A
10-1/2 in.
(267 mm)
B
A B
m m in m m
1 5 2 4 - 3 / 4 1 2 1
3 0 5 1 0 - 3 / 4 2 7 3
4 5 7 1 6 - 3 / 4 4 2 5
6 1 0 2 2 - 3 / 4 5 7 8
9 1 4 3 4 - 3 / 4 8 8 3
1 2 1 9 4 6 - 3 / 4 1 1 8 7
Inside
Diameter
8 in.
(203 mm)
Outside
Diameter
10-1/2 in.
(267 mm)