Getting Started - Jenn-Air JFFCC72EFS00 Use And Care Manual

INSTALLATION CHECKLIST
✔ Electrical Power
Plug refrigerator into a grounded 3 prong outlet.
■
✔ Doors
If doors need to be removed during installation, see the
■
"Remove and Replace Doors" in the instructions.
Check that handles are secure and installed according to the
■
instructions.
Doors seal completely.
■
Refrigerator is level. (Remove base grille and adjust leveling
■
feet so they are snug against the floor.)
Doors are even across the top. (Use door alignment feature if
■
necessary.)
Base grille is properly attached to the refrigerator.
■
✔ Ice and Water System (on some models)
Connect refrigerator to a cold water supply with 20-120 psi
■
water pressure, as specified in the instructions.
Make sure the household water supply is connected and
■
turned on.
Check that the water supply line behind refrigerator is not
■
kinked.
Only use recommended water supply tubing, copper, or PEX,
■
as specified in the instructions.
Install water filter according to the instructions.
■
Flush water system with 3 gallons of water, as specified in the
■
instructions.
Check for water leaks at all connections.
■
Turn on ice maker if refrigerator is connected to water supply.
■
(If not connected to water supply, turn off ice maker.)
✔ Final Checks
Install air filter according to instructions in corresponding
■
packaging.
Remove all shipping material.
■
Set temperature controls to the recommended setting.
■
Save instructions and other literature.
■
Send in Registration Card or register your product online.
■
WATER FILTER INSTALLATION
Locate the water filter compartment in the lower left-hand side
■
of the refrigerator compartment. Push on the right side of the
filter door to open.
Align the arrow on the water filter cap with the cutout notch in
■
the filter housing and insert filter.
Once the filter is inserted, turn the filter clockwise 90° (¼ turn)
■
until it locks into the housing.
Push water filter door closed to latch.
■
Flush 3 gallons of water through the water system to clear air
■
from the water line and to keep the dispenser from dripping
and/or avoiding decreased dispenser flow.
NOTE: If the filter is not installed correctly, water may
dispense at a lower flow rate and there will be slower ice
production. Improper filter installation may also cause the
water filter housing to leak.
6

GETTING STARTED

DOOR ALIGNMENT
Align Refrigerator Doors
✔ If doors are uneven:
Ensure the refrigerator is level.
■
Keeping both refrigerator doors closed, pull out the freezer
■
drawer. Locate the bottom hinge pin of the right-hand
refrigerator door. The alignment screw is inside the bottom
hinge pin.
Insert the short end of the ¹⁄
■
Door Handle Installation Instructions) into the bottom hinge pin
until it is fully engaged in the alignment screw.
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.
Continue to turn the alignment screw until the tops of the door
■
are aligned.
Shelf Height Adjustment
Shelf height can be adjusted by changing the adjustable shelf
mounts between their vertical and horizontal positions.
Carefully lift the shelf off the shelf mounts and turn the flipper
■
to the desired orientation.
Repeat for remaining shelf mounts.
■
Ensure the shelf is properly seated on the shelf mounts.
■
ENERGY SAVER MODE AND NORMAL
OPERATING SOUNDS
Your new French door bottom mount refrigerator has been
designed to optimize energy efficiency and better regulate
temperatures to match cooling demand.
You may notice that it operates differently from your previously
owned refrigerator.
It is normal for the high-efficiency compressor to run for extended
periods of time at varying speeds in order to consume only the
energy necessary for optimum efficiency.
In addition, during various stages of the cooling cycle, you may
hear normal operating sounds that are unfamiliar to you.
Energy Saver Mode
A selectable feature that turns off the heaters around the
refrigerator doors and dispenser. When this feature is enabled,
condensation may form on the front of the refrigerator cabinet,
gasket, or on top of the freezer drawer. Savings may vary based
on the relative humidity of environment.
" hex-key wrench (packed with the
8