Panasonic TH-86EQ2W Operating Instructions Manual page 75

■
[Network control]
Set when controlling with the unit's LAN terminal.
[Off]:
Invalidates control with LAN terminal.
(In this case, the power consumption of Standby
condition (when the power is turned off with the
remote control) will be slightly reduced.)
[On]:
Controls via LAN using the LAN terminal. The
power indicator lights purple when the power is
turned off with the remote control (standby).
Note
●
When using the LAN control function which is
described in "Using Network Function" (see page
90 ‒ 114), set this function to [On].
●
Even if the setting is set to [Off], the Web browser
control screens that do not control this unit (display
information [Status], detailed settings [Detailed set
up] and password change [Change password])
operate.
● To enable the operation, set [Quick start] to [On].
●
When [Quick start] is set to [Off], the power can
be turned off via network control even if [Network
control] is set to [On]. However, the power cannot
be turned on from standby state with the exception
after a wake-up message (magic packet) is sent
from the network equipment in the network. To
control both, it is necessary to set both [Quick start]
and [Network control] to [On] respectively.
■
[PJLink settings]
Configure the PJLink settings to enable PJLink
communication on the unit.
PJLink settings
Password policy
PJLink control
Password
PJLink notification
Notified IP address 1
Notified IP address 2
Save
[Password policy]:
Precautions for password settings of this item will be
displayed in a new window.
[PJLink control]:
Specifies the PJLink communication settings.
Off:
Disables PJLink control.
On: Enables PJLink control.
[Password]:
The keyboard for setting the password is displayed.
After entering the password, select [Ok]; the
confirmation screen is displayed. Enter the password
again and select [Ok]; the password is determined.
● Entering characters (see page 165)
[PJLink notification]:
Set this item when using the PJLink notification.
On
Off
192.168.0.100
192.168.0.101
[Off]:
Disables the notification.
[On]:
Enables the notification.
[Notified IP address 1], [Notified IP address 2]:
Set the IP address of the PC where the status of this
unit is notified.
[Save]:
Saves the password determined above in the display
unit.
Note
●
Once determined, it is necessary to enter the
password to display the settings.
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
●
To use PJLink control, you need to set [On] to the
setting and set [Network control] to [On].
●
The password for the setting is different from the
password for [LAN setup].
■
[AMX D. D.]
Set whether to allow the Display to be detected by AMX
Device Discovery.
[Off]:
Disables detection by AMX Device Discovery.
[On]:
Enables detection by AMX Device Discovery.
●
For more details, visit the following web site.
http://www.amx.com/
Note
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
■
[Crestron Connected]
When this function is set to [On], the Display can be
monitored or controlled via the network using equipment
and application software of Crestron Electronics, Inc.
This Display supports the following application software
from Crestron Electronics, Inc.
Crestron Fusion
•
Crestron Connected is a function to connect to a system
developed by Crestron Electronics, Inc. which manages
and controls multiple system devices connected to the
network.
●
For details of Crestron Connected, refer to the
Crestron Electronics, Inc. web site (Provided only in
English).
http://www.crestron.com/
Note
●
To set the setting to [On], you must configure
[Administrator account settings] in advance.
75
English