It is suggested that you keep the original packaging so that the system can be repacked at a future date if necessary. Please note that neither Martin Audio nor its distributors can accept any responsibility for damage to any returned product which arises through the use of non-approved packaging.
The grilles are black perforated steel with an acoustically transparent black scrim cloth backing. Despite their power handling and SPL output, LE Series monitors are light in weight to aid handling, transportation and set-up.
LE100/LE200 USER GUIDE ® COAXIAL DIFFERENTIAL DISPERSION TECHNOLOGY LE Series monitors feature Martin Audio’s unique, patented Coaxial Differential Dispersion ® technology. The design augments the ‘point-source’ benefits of coaxial drivers with the ® consistency of coverage which Coaxial Differential Dispersion technology can deliver.
There are two models in the LE range: one based on a 12” driver, the other on a 15” driver. Both models are 8 ohms impedance. The basic characteristics of the two models are summarised below (full specifications at “LE Series Specifications” on page 1): Model LF driver (dia.)
“daisy-chain” the amplifier output to the next speaker. Important: please ensure that the total impedance of multiple LE Series monitors connected in this way is not less than the minimum load impedance the amplifier channel can drive: No.
LE100/LE200 USER GUIDE LE200 ONLY – CROSSOVER MODES The LE200 may be bi-amped if wished. Configuration data for external electronic crossovers or system controllers can be found at “Speaker Parameters”). The LE200 may be switched between passive (full-range) mode and bi-amped mode with the switch on the recessed front panel between the two connectors.
Martin Audio MA Series two and four channel power amplifiers are recommended for use with LE Series stage monitors. These amplifiers work well at 4 ohms, making it possible to power two cabinets in parallel from each amplifier channel. Models are available with power ratings from 700 W/ch.
Alternative high quality loudspeaker management systems may be used. The table on the following page lists the parameters for each LE Series monitor that need to be entered into the controller for safe and optimised operation. Please note that the data provided is based on the algorithms used by Martin Audio DX Series Loudspeaker Management Systems;...
Page 11
LE100/LE200 USER GUIDE LE100/LE200 User Guide V1.0...
USER GUIDE MOUNTING OPTIONS As wedge monitors, LE Series monitors will most often be used as free-standing cabinets in “landscape orientation” at floor level. The enclosures are fitted with moulded rubber feet on the base which protect the stage and help the units to retain their position.
Page 13
LE100/LE200 USER GUIDE It can be seen from the the views above that the coaxial driver is not symmetrical. For correct performance, the driver should always be orientated as shown, with the “butterfly wings” of the HF driver assembly biased towards the bottom of the enclosure. To rotate the driver, proceed as follows: 1.
USER GUIDE Grille removal and replacement Grilles on LE Series monitors are designed to be easy to remove to facilitate driver rotation. No screws are used to hold them in place; they are manufactured with a natural spring which holds them in place in slots in each side of the cabinets.
Page 15
LE100/LE200 USER GUIDE Now lift the handle up; this will ease the grille forward slightly to prevent the return on the grille dropping straight back into the slot: Repeat this process for the remaining gaps in the grille to ease it out of the slot all the way up one side of the cabinet;...
USER GUIDE Badge rotation The Martin Audio badge is spring loaded and can be rotated through 180 degrees to maintain a professional appearance. To do so, remove the grille and push the badge forward from the rear while turning it to the desired orientation. Once complete, refit the grille.
Martin Audio Ltd. cannot be held responsible for defects caused by unauthorised modifications, improper use, negligence, exposure to inclement weather conditions, act of God or accident, or any use of this product that is not in accordance with the instructions provided by Martin Audio. Martin Audio is not liable for consequential damages.
Page 20
Copyright Martin Audio Ltd. Martin Audio and Coaxial Differential Dispersion are registered trademarks of Martin Audio Ltd and are registered in the United Kingdom, United States and other countries. All other trademarks and trade names are the property of their respective owners.