Force And Timer To Close; Program Limits - Chamberlain CB24 Owner's Manual

FORCE AND TIMER TO CLOSE

FORCE CONTROL
Set the sensitivity such that the unit will
complete a full cycle of gate travel but will
reverse off an obstruction without applying
an unreasonable amount of force.
MIN MAX
INSTALL ALL EQUIPMENT IN COMPLIANCE WITH EN60335-2-103, EN13241-1.
P R O G R A M L I M I T S
1. Turn BiPart switch to desired setting. Set to "Off" for single
gate applications.
2. Press the "LEARN LIMITS" button.
3. The "SET OPEN LIMIT" LED will blink.
4. Use any of the "Gate 1" buttons to move Gate 1 to the
desired open position. Repeat if Gate 2 is present using "Gate
2" buttons.
5. Press the "LEARN LIMITS" button to set the Open Limit for
gate(s).
6. The "SET OPEN LIMIT" LED will turn off. The "SET CLOSE
LIMIT" LED will blink.
7. Use the "Gate 1" buttons to move Gate 1 to the desired close
position. Repeat if Gate 2 is present using "Gate 2" buttons.
8. Press the "LEARN LIMITS" button to set the close limit for
gate(s).
9. The "SET CLOSE LIMIT" LED will turn off. The limits are set.
10 Using programmed remote or single button input (SBC) run
the gate(s) from the close limit to the open limit. After
reaching the open limit, run the gate(s) to the close limit.
This will learn the force in the open and close direction.
11. If the learned force is not high enough, manually
adjust the force control as described above.
W W ARN ARNING
CAUTION CAUTION
The "Save" Dip switch must be set to OFF to allow programming.
After completion set the "Save" switch back to on.
NOTE: Any following SBC or Remote inputs will move the gate.
BIPART DELAY
Set the BIPART DELAY to desired
setting. The range is 0 to 8
seconds, 0 seconds is OFF.
OFF
ING
MAX
J19
K6
ALARM
NO
C
K5
MAGLOCK
NO
L1
C
1
NC
R2
LEARN
Z1
XMITTER
R1
10A 32V
2
GATE 1
F3
BRN
D1Ø K2
GRN
WHT
YEL
BLU
RED
SET
K1
Q9
Z12 OPEN
LIMIT
R9Ø
ACCESSORY
POWER
24V
R1Ø1
BRN R1ØØ
F4
GRN
ACCESSORY
10A 32V
OVLD
WHT
K4
YEL
F5
BLU
D21
RED
K3
D8
GATE 2
D22
Q22
D15
R196
R4 C2
24 VAC/
SOLAR
INPUT
MOV2
J4
MOV1
JMPR2
DB1
DIAGNOSTIC
SET
OPEN
LIMIT
14
TIMER TO CLOSE ENABLE
Set the TIMER TO CLOSE to
desired setting. The range is 0 to
180 seconds, 0 seconds is OFF.
OFF MAX
P2
R223
Ø14GPØ89ØE
Ø14LGØ89ØE
Ø14SKØ89ØE
R2Ø7
Z2Ø
R227
J18
R224
Z22
U4
OFF ON SAVE R92
OFF ON MAGLOCK
SINGLE DUAL MODE
NO NC EDGE
NO NC PHOTO
S1
R91
R94
DIAGNOSTIC
R93
GATE 1
SET
LEARN
CLOSE
24V
LIMITS
LIMIT
TIMER
GATE 2
COM OVLD
RUNNING
OVLD
BIPART TIMER TO SINGLE
DELAY CLOSE BUTTON
FORCE
OPEN
SINGLE BUTTON
RESET
STOP
MIN MAX OFF MAX OFF MAX
COM
COM
R35 POWER
D9
C12
D27 Z3
F7
Z4
C13
C4
SHADOW
U3
INTERRUPT
C11
CHGR COM
OVLD
F6
F2
F1 20A 32V
R9 D4
D1 FUSE
C64
BATT 2 BATT 1
OPEN
JMPR1
U2 D2
GATE 1
W W ARN ARNING ING
SET
LEARN
CLOSE
LIMITS
LIMIT
W W ARN ARNING ING
GATE 2
FORCE
CLOSE
EDGE
OPEN EDGE/
PHOTO
Z9
OPEN
PHOTO
Z8
CLOSE
PHOTO
SWITCHED
ACCESSORY
POWER
CONTROL
INPUTS
LOOP
INPUTS