Panasonic KX-FP207FX-S Service Manual page 63

11.1.3. Service Function Table
Code Function
501 Pause time set
503 Dial speed select
510 VOX time (KX-FP218)
511 VOX sense (KX-FP218)
514 Bell detection time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
544 Document feed position adjustment
value set
550 Memory clear
551 ROM check
552 DTMF single tone test
553 Monitor on FAX communication
select
554 Modem test
555 Scan check
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
561 KEY test
567 T0 timer
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection
time set
573 Remote turn-on ring number set (KX-
FP207)
573 Remote turn-on ring number set (KX-
FP218)
574 Dial tone detect check
Set Value Effective
Range
X 100 msec 001~600
1: 10 pps 1, 2
2: 20 pps
1:8sec 1~3
2:6sec
3:4sec
1:High 2:Low 1, 2
X 100 msec 1~9
1:2100 Hz 1, 2
2:1100 Hz
1:ON 2:OFF 1, 2
1:ON 2:OFF 1, 2
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1~9 mm 1~9
1:ON 2:OFF 1, 2
1:OFF 1~3
2:PHASE B
3:ALL
1:ON 2:OFF 1, 2
X second 001~255
1:61% 2:67% 1, 2
X number of 00~99
times
X second 001~999
X number of 00~99
rings
X number of 00~99
rings
1:ON 2:OFF 1, 2
63
Default
30
1
2
1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to "LOW".
6
1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not either transmit/receive long distance or interna-
tional communications (P.93).
1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not either transmit/receive long distance or interna-
tional communications (P.93).
1 The resolution reverts to the default when transmission
is complete.
1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
5 When the ADF function is in correct, adjust the feed
position.
See Memory Clear Specification (P.66).
See Test Mode (P.58).
2 See Test Mode (P.58).
1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
See Test Mode (P.58).
See Test Mode (P.58).
0 See Test Mode (P.58).
See Test Mode (P.58).
See Test Mode (P.58).
1 Sets whether or not to detect a paper jam. If a docu-
ment with a length longer than 600 mm is copied or
transmitted, the unit stops copying or transmitting as a
paper jamming because a document over 600 mm is
not normal. In the factory, transmitting or copying a doc-
ument longer than 600 mm is done as an aging test. In
this case, OFF is selected.
See Test Mode (P.58).
046 Sets a higher value when the response from the other
party needs more time during automatic FAX transmis-
sion.
1 Sets the % break of pulse dialling according PBX.
11 Selects the number of times that ITS is redialled (not
including the first dial).
040 Sets the interval of ITS redialling.
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
2
KX-FP207FX-S/FP218FX-S
Remarks
----------
----------
----------
----------
----------