Page 2
NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.
Page 3
Revision Record Issue Date Remarks Apr 2019 First Issue...
Page 5
! Important: Install the Floor Mount Kit before installing the Ceiling Mount Kit. For more information on the Floor Mount Kit, refer to 2247 Floor Mount Kit (2247-K042). Floor to ceiling installation requires the kiosk to be bolted to the floor using four anchors and to the concrete slab ceiling using four anchors.
Page 8
Ceiling Mount Only Item Part Number Qty Description 497-0525206 2247–K040 Ceiling Mount Only Kit 006-8624305 Rectangle Blanking Plug (42 x 24 mm) 009-0006599 40 Screw M6 X 12 M/C Combi Pozi 497-0518396 Ceiling Post Metal Bracket, 2245 497-0519612 Pole Ceiling Bracket, 2245 497-0519613...
Page 9
Ceiling Mount Only Installations Procedures Installing the Ceiling Mount kit involves the following procedures: 1. Remove the Ceiling Connector brackets to disassemble the poles. a. Remove the screws that secure the front and rear Ceiling Connector brackets together (four screws for each pair). b.
Page 10
3. Mark and drill ceiling holes. For procedures, refer to Marking and Drilling Ceiling Mounting Holes on page 12. 4. Install the Ceiling Mounts. For procedures, refer to Installing the Ceiling Mount page 19. Note: For installation procedures of other kiosk components, refer to NCR SelfServ™ XK32 (2245) Kiosk Operator Guide (BCC5-0000-5247).
Page 11
Ceiling Mount Only Cutting the Ceiling Posts The Ceiling Posts have an initial length of 2000 mm (78.74 in.). This length needs to be cut to length A as appropriate for the Floor to Concrete Ceiling height of the installation site.
Page 12
Ceiling Mount Only Ceiling Posts for Maximum Height Installation This section provides the appropriate Ceiling Posts length for Maximum Height installation, 4000 mm (157.48 in.). For installation heights less than the maximum, see Ceiling Posts for Lowered Height Installation on page 10. For a Maximum Height Installation, the Ceiling Posts should have a length of 1995 mm (78.54 in.) as shown in the illustration below.
Page 13
Ceiling Mount Only Cut off 5 mm (0.20 in.) from the straight edge of the Ceiling Posts and then apply rust protection paint on the edges where the cut was made.
Page 14
Ceiling Mount Only Ceiling Posts for Lowered Height Installation This section determines the appropriate Ceiling Posts length for Lowered Height installations . For maximum installation height, see Ceiling Posts for Maximum Height Installation on page 8. 1. Determine the Ceiling Post length (A) as appropriate for the installation site.
Page 15
Ceiling Mount Only 2. Cut off the excess length of the Ceiling Post and apply rust protection paint on the edges where the cut was made.
Page 16
Ceiling Mount Only Marking and Drilling Ceiling Mounting Holes Marking mounting holes for the Ceiling Mount assembly requires at least two persons and the use of a step ladder or a work platform. Make sure that the Ceiling Posts are cut to the appropriate length, see Cutting the Ceiling Posts on page 7 for more information.
Page 17
Ceiling Mount Only To mark and drill mounting holes for the Ceiling Mount, perform the following steps: 1. Install the Ceiling Posts to the kiosk. a. Insert the Ceiling Posts into the Main Frame. b. Secure the Ceiling Posts to the cabinet using four M6 hex head screws for each post.
Page 18
Ceiling Mount Only 2. Mount and secure one side of the Ceiling Connector brackets to the Ceiling Pole Bracket. 3. Position the Ceiling Pole Bracket assembly at the top of the Ceiling Posts. a. Insert the Ceiling Posts into the Ceiling Connector brackets.
Page 19
Ceiling Mount Only b. Mount the second side of the Ceiling Connector brackets and secure these using two screws to their opposite connector bracket. c. Secure the second connector bracket sides to the Ceiling Pole Bracket using four screws each.
Page 20
Ceiling Mount Only 4. Hold the Ceiling Mount against the Concrete Ceiling slab and then mark the following mounting holes: a. Four mounting holes on the concrete ceiling. b. Eight mounting holes on each of the Ceiling Post for the Ceiling Connector Brackets.
Page 21
Ceiling Mount Only 5. Remove the Ceiling Pole Bracket and Ceiling Connector Brackets from the Ceiling Posts. 6. Remove the Ceiling Posts from the Kiosk. 7. Drill the four mounting holes on the ceiling and install the four anchors. a. Cover the kiosk to protect it from dust and debris. b.
Page 22
Ceiling Mount Only 8. On each Ceiling Post, drill eight 3 mm (0.12 in.) mounting holes on the marked locations for the Ceiling Connector brackets.
Page 23
Ceiling Mount Only Installing the Ceiling Mount Installing the Ceiling Mount assembly requires at least two persons and the use of a step ladder or a work platform.
Page 24
Ceiling Mount Only To install the Ceiling Mount, perform the following steps: 1. Mount and secure the Ceiling Pole bracket to the anchor bolts using four M10 nuts. 2. Install the Ceiling Posts to the kiosk. a. Insert the Ceiling Posts into the Main Frame.
Page 25
Ceiling Mount Only b. Secure the Ceiling Posts to the Main Frame using four M6 hex head screws for each post. 3. Secure the Ceiling Posts to the Ceiling Pole bracket using the Ceiling Connector brackets. a. Mount and secure the front Ceiling Connector brackets using six M6 screws on each connector bracket.
Page 26
Ceiling Mount Only b. Mount and secure the rear Ceiling Connector brackets using six M6 screws on each connector bracket. c. Secure the front and rear Ceiling Connector brackets together using four screws for each pair.