Option Settings; Shutter; Osd; Auto Keystone - Panasonic PT-L780U Operating Instructions Manual

Option settings

Select the item pressing the F or G
buttons on the remote control unit or
the projector.
Press the I or H buttons to adjust
the selective items. To make the
SHUTTER or WEB PASSWORD
(PT-L780NTU only) functions work,
press the ENTER button.
OPTION

SHUTTER

OSD

OFF

AUTO KEYSTONE

OFF

RGB/YPbPr

RGB

RGB2 SELECT

INPUT OUTPUT

BACK COLOR

BLUE

FRONT/REAR

FRONT

DESK/CEILING

DESK CEILING

LAMP POWER

LOW

LAMP RUN TIME

10 H
NEXT PAGE @
SELECT:[^][@] ENTER:[ENTER]
ADJUST:[{][}] ESC:[MENU]
OPTION
PREVIOUS PAGE ^

FAN CONTROL

STANDARD

WEB CONTROL

OFF

WEB STANDBY

OFF
WEB PASSWORD
CONTROL KEY OFF
FUNC1 MUTE KEYSTONE
SET ID ALL
AUTO POWER OFF DISABLE
SELECT:[^][@] ENTER:[ENTER]
ADJUST:[{][}] ESC:[MENU]
SHUTTER
The shutter function can be used to
momentarily turn off the picture and
sound from the projector when the
projector is not being used for short
periods of time, such as during
breaks in meetings or when carrying
out preparation. The projector uses
less power in shutter mode than it
does in normal projection mode.
44
All manuals and user guides at all-guides.com
OSD
ON
The current input name is displayed
in the top-right corner of the screen
when the input signal is changed.
OFF
Use this setting when you do not want
the current input name to be displayed.
AUTO KEYSTONE
This should normally be set to ON.
ON
ON
ON
YPbPr During automatic setup, the angle of
tilt of the projector is detected and
BLACK
REAR
vertical keystone distortion is
corrected automatically.
HIGH
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during automatic
setup, such as when the screen
itself is at an angle.
RGB/YPbPr
HIGH
ON
This setting is valid when 750p,
ON
HDTV60, HDTV50, 525p, 625i and
ON
525i signals are being input. Select
the setting in accordance with the
input signal.
The RGB/YPbPr item is displayed
when an RGB1 IN, RGB2 IN or
RGB 3 IN connectors has a signal
being input.
RGB2 SELECT
This setting is used to select the
function of the RGB2 IN/RGB OUT
connector.
The selected input source (RGB1 or
RGB3) is output when RGB OUT is
selected.
BACK COLOR
This sets the colour which is
projected onto the screen whe
signal is being input to the pro
FRONT/REAR
This setting should be change
accordance with the projector
setting-up method.
Set to "FRONT" when using a
normal reflective screen with t
projector positioned in front of
screen, and set to "REAR" wh
using a translucent screen with
projector positioned behind the
screen.
DESK/CEILING
This setting should be change
accordance with the projector
setting-up method.
Set to "DESK" when setting up
projector on a desk or similar,
set to "CEILING" when suspen
the projector from the ceiling u
the ceiling bracket which is so
separately.
LAMP POWER
This setting changes the lamp
brightness. When set to "LOW"
luminance of the lamp is reduce
the projector uses less power, a
the operating noise is also redu
This can help to extend the lam
operating life. If using the projec
small rooms where high lumina
not required, it is recommended
you set the LAMP POWER to "
LAMP RUN TIME
This setting displays the usage
for the lamp unit which is curre
being used. If the lamp unit is
replaced in the way described
page 64, the cumulative usage