Table of Contents
Advertisement
C
Select D.S.T. mode
Press OK or
to move the highlight bar to "D.S.T.", then press
e
repeatedly until the desired setting is selected.
rt
AUTO: Select if you want to adjust your VCR's clock
automatically by the incoming signal from the host
channel. (Auto Daylight Saving Time enables automatic
adjustment of the VCR's clock at the start and end of
Daylight Saving Time.) Be sure to select the correct time
zone manually in step 4.
ON:
Adjustment will be made by the built-in clock itself.
OFF:
Select when Daylight Saving Time does not apply to you.
D
Select time zone
Press OK or
to move the highlight bar to "TIME ZONE", then
e
press
repeatedly until "AUTO" or the desired time zone is
rt
selected. Each time you press the button, the time zone changes as
follows:
AUTO
ATLANTIC
{
{
{
MOUNTAIN
PACIFIC
{
{
(back to the beginning)
{
E
Complete Semiauto Clock Set
Press MENU to return to normal screen. Turn off the VCR. "Aut"
will appear on the display panel while the clock is being set. The
current clock time will appear automatically when the clock
setting is complete.
Selections of host channel and D.S.T. mode will be reset to
"AUTO" after a power failure occurs.
Setting clock manually
— Manual Clock Set
First follow steps 1 to 2 in "Preparations" above, then go to the
following steps.
A
Set time, date and year
Press
until the desired time appears,
rt
then press OK or
. Set the date and year
e
in the same way.
● Holding
changes the time in 30-
rt
minute intervals, or changes the date in
15-day intervals.
B
Select D.S.T. mode
Press OK or
to move the highlight bar to
e
"D.S.T.", then press
to select the
rt
desired setting.
ON: Adjustment will be made by the
built-in clock itself.
OFF: Select when Daylight Saving Time
does not apply to you.
C
Start clock
Press MENU and normal screen appears.
To make corrections any time during the process
Press OK or
repeatedly until the item you want to change
e
blinks, then press
.
rt
Manual setting of the clock will be lost after a power failure
occurs.
EASTERN
CENTRAL
{
ALASKA
HAWAII
{
{
Tuner Setting
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Setting channels automatically
— Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
A
Access Main Menu screen, then Tuner
Set screen
Press MENU on the Remote. Press
move the highlight bar (arrow) to "TUNER
SET", then press OK or
B
Perform Auto Channel Set
Press
to move the highlight bar
rt
(arrow) to "AUTO CHANNEL SET", then
press OK or
. The VCR selects the correct
e
band (TV or CATV) automatically during
Auto Channel Set.
● When Auto Channel Set is complete,
"SCAN COMPLETED" appears on
screen.
● If the scan was unsuccessful, "SCAN
COMPLETED–NO SIGNAL–" appears on
screen. Check the connections and start
again.
Press MENU to return to normal screen.
Setting channels manually
— Manual Channel Set
You can add the channels you want or delete the channels you do
not want manually.
A
Access Main Menu screen, then Tuner
Set screen
Press MENU on the Remote. Press
move the highlight bar (arrow) to "TUNER
SET", then press OK or
B
Access Manual Channel Set screen
Press
to move the highlight bar
rt
(arrow) to "MANUAL CHANNEL SET",
then press OK or
.
e
C
Add or skip desired channels
To add channels
A Press the Number keys on the Remote
to input a channel number you want to
add.
B Press OK or
to set to "ADD".
e
C Repeat A to B to add other channels.
Press MENU to return to normal screen.
To skip channels
A Press
or the Number keys to select a channel number you
rt
want to skip.
B Press OK or
to set to "SKIP".
e
C Repeat A and B to skip other channels. Press MENU to return
to normal screen.
After a power failure occurs, band selection will be reset to
"CATV".
— 8 —
to
rt
.
e
to
rt
.
e
Advertisement
Table of Contents
