Advertisement
No
AEC-Q200 Test Item
The measured and observed characteristics should satisfy the
7 Operational Life
specifications in the following table.
Appearance
No marking defects
Capacitance
Within ±3.0% or ±0.30pF
(Whichever is larger)
Change
Q/D.F.
30pFmin. : Q≧350
10pF and over, 30pF and below:
10pFmax.: Q ≧200+10C
More than 1,000MΩ or 50Ω ・F
I.R.
(Whichever is smaller)
8 External Visual
No defects or abnormalities
9 Phisical Dimension
Within the specified dimensions
10 Resistance to
Appearance
No marking defects
Solvents
Within the specified tolerance
Capacitance
Change
Q/D.F.
30pFmin. : Q≧1000
30pFmax.: Q ≧400+20C
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
11 Mechanical
Appearance
No marking defects
Shock
Capacitance
Within the specified tolerance
Change
Q/D.F.
30pFmin. : Q≧1000
30pFmax.: Q ≧400+20C
More than 10,000MΩ or 500Ω ・F
I.R.
(Whichever is smaller)
12 Vibration
No defects or abnormalities
Appearance
Capacitance
Within the specified tolerance
Change
Q/D.F.
30pFmin. : Q≧1000
30pFmax.: Q ≧400+20C
I.R.
More than 10,000MΩ or 500Ω ・F
(Whichever is smaller)
The measured and observed characteristics should satisfy the
13 Resistance to
specifications in the following table.
Soldering Heat
No marking defects
Appearance
Within the specified tolerance
Capacitance
Change
Q/D.F.
30pFmin. : Q≧1000
30pFmax.: Q ≧400+20C
More than 10,000MΩ or 500Ω ・F
I.R.
(Whichever is smaller)
JEMCGS-0363S
Specification.
Temperature
Compensating Type
R7/L8/R9: Within ±12.5%
R7/L8 : W.V.: 25Vmin.: 0.035 max.
(GCM155R71H 562-223: 0.05max)
Q≧275+5C/2
R9 : 0.075max.
C: Nominal Capacitance(pF)
R7/L8 : W.V.: 25Vmin.: 0.025 max.
C: Nominal Capacitance(pF)
R9 : 0.05max.
R7/L8 : W.V.: 25Vmin.: 0.025 max.
C: Nominal Capacitance(pF)
R9 : 0.05max.
R7/L8 : W.V.: 25Vmin.: 0.025 max.
C: Nominal Capacitance(pF)
R9 : 0.05max.
R7/L8 : W.V.: 25Vmin.: 0.025 max.
C: Nominal Capacitance(pF)
R9 : 0.05max.
■AEC-Q200 Murata Standard Specification and Test Methods
High Dielectric Type
Apply 200% of the rated voltage for 1000±12 hours at 125±3℃(for
Δ C/R7), 150±3℃(for 5G/L8/R9).
Set for 24±2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
・ Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the maximun
operating temperature ±3℃. Remove and set for 24±2 hours at
W.V.: 16V/10V : 0.05 max.
room temperature. Perform initial measurement.
Visual inspection
Using calipers
Per MIL-STD-202 Method 215
Solvent 1 : 1 part (by volume) of isopropyl alcohol
Solvent 2 : Terpene defluxer
Solvent 3 : 42 parts (by volume) of water
W.V.: 16V/10V : 0.035 max.
1part (by volume) of propylene glycol monomethylether
1 part (by volume) of monoethanolomine
Three shocks in each direction should be applied along 3 mutually
perpendicular axes of the test specimen (18 shocks).
The specified test pulse should be Half-sine and should have a
duration :0.5ms, peak value:1500g and velocity change: 4.7m/s.
W.V.: 16V/10V : 0.035 max.
Solder the capacitor to the test jig (glass epoxy board) in the same
manner and under the same conditions as (19). The capacitor
should be subjected to a simple harmonic motion having a total
amplitude of 1.5mm, the frequency being varied uniformly between
W.V.: 16V/10V : 0.035 max.
the approximate limits of 10 and 2000Hz. The frequency range, from
10 to 2000Hz and return to 10Hz, should be traversed in
approximately 20 minutes. This motion should be applied for 12
items in each 3 mutually perpendicular directions (total of 36 times).
Immerse the capacitor in a eutectic solder solution at 260±5℃ for
10±1 seconds. Set at room temperature for 24±2 hours, then
measure.
・ Initial measurement for high dielectric constant type
Perform a heat treatment at 150+0/-10 ℃ for one hour and then set
for 24±2 hours at room temperature.
W.V.: 16V/10V : 0.035 max.
Perform the initial measurement.
3
AEC-Q200 Test Method
3 parts (by volume) of mineral spirits
Advertisement
