Table of Contents
Advertisement
Burner Input Requirements
Input ratings shown on the model/serial/rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at
a rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
For elevations above 6,560 ft (1999.5 m) a high altitude kit is
needed to avoid any reduced power output. See separate LP
gas conversion instructions sheet.
Prepare Cooktop for Installation
WARNING
Excessive Weight Hazard
Use two or more people to move and install cooktop.
Failure to do so can result in back or other injury.
Write down the model and serial numbers before installing the
cooktop. Both numbers are located on the center underside of
the burner box.
Unpack the parts supplied with your cooktop. Do not unpack
or remove the grates and burner bases from the carton until
after the cooktop is installed to reduce the risk of scratching the
cooktop.
The parts shipped with the cooktop depend on the model
ordered. See the "Tools and Parts" section for a complete list of
parts supplied with the cooktop.
Decide on the final location for the cooktop. Locate existing
wiring to avoid drilling into or severing wiring during installation.
The pressure regulator and flexible stainless steel gas supply line
can be assembled to the cooktop before or after the cooktop is
installed. See the "Make Gas Connection" section.
1. (Optional) Remove the foam strip from the hardware
package. Remove the backing from the foam strip. Apply the
foam strip with the adhesive side to the countertop on of the
edge of the cutout, front, back and sides.
NOTE: The foam strip helps keep the underside of the
cooktop frame free from debris and helps the cooktop sit flat
on uneven countertops.
A. Countertop
B. Foam strip
6
INSTALLATION INSTRUCTIONS
A
B
C
C. Cutout
Gas Supply Pressure Testing
Line pressure testing above ½ psi gauge (14" WCP)
The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of
½ psi (3.5 kPa).
Line pressure testing at ½ psi gauge (14" WCP) or lower
The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psi (3.5 kPa).
Install Cooktop
Install the pressure regulator to the cooktop before installing the
cooktop. See the "Make Gas Connections" section.
Cooktop over built-in oven
IMPORTANT: Clamping brackets should not be used.
1. Install the cooktop into the countertop cutout by tilting one
end of the cooktop into the cutout, then lowering the other
end into the cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop. If repositioning
is needed, lift the entire cooktop up to avoid scratching the
countertop.
Install cooktop into countertop
1. Remove the 2 hold-down screws located in each side of the
cooktop burner box.
2. Attach the 2 hold-down brackets to the burner box.
3. Install the mounted cooktop bracket into the countertop
cutout by tilting one end of the cooktop into the cutout.
Shift the cooktop to the side of the cutout the bracket was
lowered into. Lower the other end into the cutout so the
bracket clears the underside of the countertop. Center the
cooktop in the opening, then completely lower the cooktop
into the cutout.
4. Start the hold-down screws into the hold-down brackets.
A
B
C
D
A. Countertop
B. Wood block
5. Center the cooktop in the opening and, using a wood block
between the screw and the countertop, moderately tighten
the screws to secure cooktop.
IMPORTANT: Do not tighten screws directly against the
countertop.
E
C. Hold-down screw
D. Hold-down bracket
E. Burner box
Advertisement
Table of Contents
