Page 1 2009 Chevrolet Impala Owner Manual Seats and Restraint System ... 1-1 Head Restraints ... 1-2 Front Seats ... 1-4 Rear Seats ... 1-10 Safety Belts ... 1-13 Child Restraints ... 1-34 Airbag System ... 1-57 Restraint System Check ... 1-73 Features and Controls ...
Page 2: Canadian Owners
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet Motor Division wherever it appears in this manual. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3: Vehicle Symbols
Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this,” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Page 4: Vehicle Symbol Chart
Vehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. : Airbag Readiness Light : Air Conditioning : Antilock Brake System (ABS) : Audio Steering Wheel Controls or OnStar : Brake System Warning Light "...
Page 5: Seats And Restraint System
Section 1 Head Restraints ...1-2 Front Seats ...1-4 Manual Seats ...1-4 Power Seats ...1-5 Manual Lumbar ...1-6 Heated Seats ...1-6 Reclining Seatbacks ...1-7 Center Seat ...1-10 Rear Seats ...1-10 Split Folding Rear Seat ...1-10 Safety Belts ...1-13 Safety Belts: They Are for Everyone ...1-13 How to Wear Safety Belts Properly ...1-18 Lap-Shoulder Belt ...1-27 Safety Belt Use During Pregnancy ...1-32...
Page 6: Head Restraints
Head Restraints The vehicle’s front seats have adjustable head restraints in the outboard seating positions. CAUTION: With head restraints that are not installed and adjusted properly, there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Page 7 Pull the head restraint up to raise it. To lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place. The head restraints are not designed to be removed.
Page 8: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 9: Power Seats
Power Seats Driver Seat with Manual Lumbar, Power Seat Control, and Power Recline shown On vehicles with power seats, the controls used to operate them are located on the outboard side of the seats. To adjust the seat: • Move the seat forward or rearward by sliding the control forward or rearward.
Page 10: Manual Lumbar
Manual Lumbar Driver Seat with Manual Lumbar shown On vehicles with manual lumbar, the lever is located on the outboard side of the driver seat near the front of the seat cushion. Lift up or push down on the lever repeatedly to increase or decrease lumbar support.
Page 11: Reclining Seatbacks
Reclining Seatbacks Manual Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 12: Power Reclining Seatback
To return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Page 13 CAUTION: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 14: Rear Seats
Center Seat The vehicle may have a front center seat. There are cupholders on the underside of the seat cushion. To use them, ﬂip the seat cushion forward. The seat can also be used as a storage area by lowering the seatback. See Center Console Storage on page 2-43.
Page 15 To use this feature: 1. Make sure the front seats are not reclined. If they are, the seat cushion will not ﬂip forward completely. 2. Flip the bottom seat cushion forward by pulling up on the tab located in the center of the seat cushion where the seatback meets the seat cushion.
Page 16: Under Seat Storage
To return the seats to the normal position: CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
Page 17: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 18: Why Safety Belts Work
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 19 Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 1-15...
Page 20 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-16...
Page 21: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I...
Page 22: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt.
Page 23 Sit up straight and always keep your feet on the ﬂoor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Page 24 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. 1-20 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 25 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 26 What is wrong with this? The belt is buckled in the wrong buckle. 1-22 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 27 What is wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 28 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-24 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 29 What is wrong with this? The belt is behind the body. CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 30 What is wrong with this? The belt is twisted across the body. 1-26 CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 31: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder except for the center front passenger position, if your vehicle has one, which has a lap belt. See Lap Belt on page 1-32 for more information. The following instructions explain how to wear a lap-shoulder belt properly.
Page 32 4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. See “Shoulder Belt Height Adjustment” later in this section for instructions on use and important safety information. 5. To make the lap part tight, pull up on the shoulder belt.
Page 33 Shoulder Belt Height Adjuster The vehicle has shoulder belt height adjusters for the driver and right front passenger positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off the shoulder.
Page 34: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed on a shoulder belt, the comfort guide positions the belt away from the neck and head.
Page 35 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 36: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 37: Safety Belt Extender
To make the belt shorter, pull its free end as shown until the belt is snug. If the belt is not long enough, see Safety Belt Extender on page 1-33. Make sure the release button on the buckle is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Page 38: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-34 The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: •...
Page 39 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 40 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 41: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 42 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 43 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 44 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 45: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 46 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-42 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the...
Page 47: Where To Put The Restraint
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 48 A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates.
Page 49: Lower Anchors And Tethers For Children (Latch)
When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever a child restraint is installed, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle.
Page 50: Top Tether Anchor
Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). 1-46 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 51 Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 52: Securing A Child Restraint Designed For The Latch System
Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
Page 53 CAUTION: Do not attach more than one child restraint to a single anchor. Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a crash. A child or others could be injured. To reduce the risk of serious or fatal injuries during a crash, attach only one child restraint per anchor.
Page 54: Securing A Child Restraint In A Rear Seat Position
2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 55 Do not secure a child seat in a position without a top tether anchor if a national or local law requires that the top tether be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Page 56 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 57: Securing A Child Restraint In The Center Front Seat Position
6. If the child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-45 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Page 58: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-43. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Page 59 If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-45 for how and where to install the child restraint using LATCH. If a child restraint is secured using a safety belt and it uses a top tether, see Lower Anchors and Tethers for Children (LATCH) on page 1-45 for top tether anchor locations.
Page 60 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 1-56 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 61: Airbag System
If a child restraint has been installed and the on indicator is lit, see “If the On Indicator is Lit for a Child Restraint” under Passenger Sensing System on page 1-65 for more information. To remove the child restraint, unbuckle the vehicle safety belt and let it return to the stowed position.
Page 62 Here are the most important things to know about the airbag system: CAUTION: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
Page 63: Where Are The Airbags
CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 64 The right front passenger frontal airbag is in the instrument panel on the passenger side. 1-60 Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door.
Page 65 Driver Side shown, Passenger Side similar The roof-rail airbags for the driver, right front passenger, and second row outboard passengers are in the ceiling above the side windows. CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 66: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 67: How Does An Airbag Restrain
Roof-rail airbags are not intended to inﬂate in rollovers or rear impacts. A seat-mounted side impact airbag is intended to deploy on the side of the vehicle that is struck. Both roof-rail airbags will deploy when either side of the vehicle is struck. In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs...
Page 68: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After the frontal airbags and seat-mounted side impact airbags inﬂate, they quickly deﬂate, so quickly that some people may not even realize an airbag inﬂated. Roof-rail airbags may still be at least partially inﬂated for some time after they deploy.
Page 69: Passenger Sensing System
In many crashes severe enough to inﬂate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for the airbag system.
Page 70 The passenger sensing system will turn off the right front passenger frontal airbag under certain conditions. The driver airbag, seat-mounted side impact airbags, and roof-rail airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat.
Page 71 The passenger sensing system is designed to turn off the right front passenger frontal airbag if: • The right front passenger seat is unoccupied. • The system determines that an infant is present in a child restraint. • A right front passenger takes his/her weight off of the seat for a period of time.
Page 72 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 73 If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag:...
Page 74 Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 75: Servicing Your Airbag-Equipped Vehicle
The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat. If this is not desired, remove the object from the seat. CAUTION: Stowing of articles under the passenger seat or between the passenger seat cushion and seatback may interfere with the proper operation of the passenger sensing system.
Page 76 Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 77: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 78: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 79: Table Of Contents
Section 2 Keys ...2-3 Remote Keyless Entry (RKE) System ...2-4 Remote Keyless Entry (RKE) System Operation ...2-5 Remote Vehicle Start ...2-7 Doors and Locks ...2-9 Door Locks ...2-9 Power Door Locks ...2-10 Delayed Locking ...2-10 Automatic Door Lock ...2-10 Programmable Automatic Door Unlock ...2-11 Rear Door Security Locks ...2-11 Lockout Protection ...2-12 Trunk ...2-12...
Page 80 Section 2 Universal Home Remote System ...2-36 Universal Home Remote System Operation (With Three Round LED) ...2-37 Storage Areas ...2-43 Glove Box ...2-43 Cupholders ...2-43 Sunglasses Storage Compartment ...2-43 Features and Controls Center Console Storage ...2-43 Rear Storage Area ...2-43 Rear Seat Armrest ...2-43 Convenience Net ...2-43 Sunroof ...2-44...
Page 81: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 82: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System If this vehicle has the Remote Keyless Entry (RKE) system, it operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 83: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 195 feet (60 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-4. With Remote Start Shown, Without Remote Start Similar...
Page 84: Battery Replacement
(Vehicle Locator/Panic Alarm): Press and release to locate the vehicle. The turn signal lamps ﬂash and the horn sounds three times. Press and hold than two seconds to activate the panic alarm. The turn signal lamps ﬂash and the horn sounds repeatedly for 30 seconds.
Page 85: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature.
Page 86 If it is the ﬁrst remote start since the vehicle has been driven, repeat the previous steps, while the engine is still running, to extend the engine running time by 10 minutes from the time you repeat the steps for remote starting.
Page 87: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Page 88: Power Door Locks
Power Door Locks A power door lock switch is located on both front doors next to the door handle. Press the top of the switch to unlock all doors or press the bottom of the switch to lock all doors. If the vehicle has the optional content theft-deterrent system and it is armed, the power door lock switches will be disabled.
Page 89: Programmable Automatic Door Unlock
Programmable Automatic Door Unlock The vehicle is programmed so that when the shift lever is moved into P (Park) all doors will unlock. With the vehicle stopped and the engine running, door unlocking can be programmed through prompts displayed on the Driver Information Center (DIC). These prompts allow the driver to choose various unlock settings.
Page 90: Lockout Protection
To open a rear door when the security lock is on, do the following: 1. Unlock the door using the Remote Keyless Entry (RKE) transmitter, if the vehicle has one, the power door lock switch, or by lifting the rear door manual lock.
Page 91: Trunk Release
Trunk Release To open the trunk from the outside, press the trunk release button on the RKE transmitter, if equipped. Remote Trunk Release (Remote Trunk Release): Press the button located next to the exterior lamps control on the left side of the instrument panel to open the trunk.
Page 92: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 93: Power Windows
Power Windows CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window.
Page 94: Sun Visors
Express-Down Window The driver window switch has an express-down feature labeled AUTO. This lets you lower the window completely without holding the switch. Press the front of the switch to the second position and release. To stop the window while it is lowering, brieﬂy pull up on the switch.
Page 95: Pass-Key Iii+ Electronic Immobilizer
Once armed, the alarm will go off if someone tries to enter the vehicle without using the RKE transmitter or a key or turns the ignition on with an incorrect key. The horn will sound and the turn signal lamps will ﬂash for about 30 seconds.
Page 96: Immobilizer Operation
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 97: Starting And Operating Your Vehicle
See your dealer/retailer or a locksmith who can service ® PASS-Key III+ to get a new key blank that is cut exactly as the ignition key that operates the system. To program the new additional key: 1. Verify that the new key has a 2.
Page 98: Ignition Positions
Ignition Positions The ignition switch has four different positions. To shift out of P (Park), the ignition must be in ON/RUN and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key.
Page 99: Starting Procedure
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine turned off: • Audio System • Power Windows • Sunroof The radio will work when the key is in ON/RUN or ACC/ACCESSORY. Once the key is turned from ON/RUN to LOCK/OFF the radio will continue to work 10 minutes or until the driver door is opened.
Page 100: Engine Coolant Heater
2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Try pushing the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for up to a maximum of 15 seconds.
Page 101: Active Fuel Management™ (5.3L V8 Engine)
CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a ﬁre. You could be seriously injured. Plug the cord into a properly grounded three-prong 110-volt AC outlet.
Page 102: Automatic Transmission Operation
Automatic Transmission Operation The automatic transmission has a shift lever on the steering column or on the console between the seats. There is a display, located on the instrument panel cluster that will indicate the gear the vehicle is in. Maximum engine speed is limited on automatic transmission vehicles while in P (Park) or N (Neutral) to protect driveline components from improper operation.
Page 103 R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
Page 104: Parking Brake
3 (Third): This position is also used for normal driving. However, it reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill.
Page 105: Shifting Into Park
A warning chime will sound and a brake warning light located on the instrument panel cluster will come on, if the parking brake is set, the ignition is on and the vehicle speed is greater than 5 mph (8 km/h). Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts.
Page 106: Console Shift Lever
Console Shift Lever If the vehicle is equipped with a console shift lever, use this procedure to shift the vehicle into P (Park): 1. Hold the brake pedal down. 2. Move the shift lever into P (Park) by pushing the lever all the way toward the front of the vehicle and then to the left.
Page 107: Shifting Out Of Park
If torque lock does occur, your vehicle may need to be pushed uphill by another vehicle to relieve the parking pawl pressure, so you can shift out of P (Park). Shifting Out of Park Automatic Transmission Shift Lock The vehicle has an electronic shift lock release system. The shift lock release is designed to: •...
Page 108: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 109: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 110: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Pull the lever, located at the bottom of the mirror for nighttime use.
Page 111: Outside Convex Mirror
2. Press one of the four buttons located on the control pad to move the mirror to the desired direction. 3. Adjust each outside mirror so that a little of the vehicle and the area behind it can be seen. Keep the selector switch in the center position when not adjusting either outside mirror.
Page 112 OnStar Turn-by-Turn Navigation service, with one trial route, is available on most vehicles. Press the OnStar button to have an OnStar advisor contact Roadside Service. OnStar service is provided subject to the OnStar Terms and Conditions included in the OnStar Subscriber glove box literature.
Page 113: Onstar Virtual Advisor
OnStar Hands-Free Calling OnStar Hands-Free Calling allows eligible OnStar subscribers to make and receive calls using voice commands. Hands-Free Calling is fully integrated into the vehicle, and can be used with OnStar Pre-Paid Minute Packages. Most vehicles include 30 trial minutes good for 60 days.
Page 114: Universal Home Remote System
This information usually includes the vehicle’s GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the Virtual Advisor feature of OnStar Hands-Free Calling is used, the vehicle also sends OnStar the vehicle’s GPS location so they can provide services where it is located.
Page 115 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 116 Programming Universal Home Remote — Rolling Code For questions or help programming the Universal Home Remote System, call 1-866-572-2728 or go to www.learcar2u.com. Most garage door openers sold after 1996 are Rolling Code units. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
Page 117 4. Immediately, within one second, release the button when the garage door moves. The indicator light will blink rapidly until programming is complete. 5. Press and release the same button again. The garage door should move, conﬁrming that programming is successful and complete. To program another Rolling Code device such as an additional garage door opener, a security device, or home automation device, repeat Steps 1-5, choosing...
Page 118 The garage door opener receiver (motor head unit) could also have a row of dip switches that can be used when programming the Universal Home Remote. If the total number of switches on the motor head and hand held transmitter are different, or if the dip switch settings are different, use the dip switch settings on the motor head unit to program the Universal Home Remote.
Page 119 2. Write down the eight to 12 switch settings from left to right as follows: • When a switch is in the up position, write “Left.” • When a switch is in the down position, write “Right.” • If a switch is set between the up and down position, write “Middle.”...
Page 120: Reprogramming Universal Home Remote Buttons
5. After entering all of the switch positions, again, ﬁrmly press and release all three buttons at the same time. The indicator lights will turn on. 6. Press and hold the button that will be used to control the garage door until the garage door moves.
Page 121: Storage Areas
Storage Areas Glove Box Lift up on the glove box lever to open it. Cupholders Cupholders may be built into the front center console, front portion of the front center seat, and rear armrest of the vehicle. Sunglasses Storage Compartment A storage compartment for sunglasses may be located above the rearview mirror.
Page 122: Sunroof
Sunroof On vehicles with a sunroof, the sunroof switches are located on the overhead console. The sunroof can only be operated when the ignition is in ON/RUN, ACC/ACCESSORY, or when Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-21. 2-44 (Vent/Express-Open): Press this switch once to vent the sunroof when it is closed.
Page 123 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-8 Windshield Washer ...3-9 Cruise Control ...3-9 Exterior Lamps ...3-12 Daytime Running Lamps (DRL)/Automatic Headlamp System ...3-14 Fog Lamps ...3-14...
Page 124 Section 3 Oil Pressure Light ...3-39 Security Light ...3-39 Fog Lamp Light ...3-40 Cruise Control Light ...3-40 Highbeam On Light ...3-40 Fuel Gage ...3-41 Driver Information Center (DIC) ...3-42 DIC Operation and Displays ...3-42 DIC Compass ...3-47 DIC Warnings and Messages ...3-49 DIC Vehicle Customization ...3-57 Instrument Panel Audio System(s) ...3-63...
Page 125 ✍ NOTES...
Page 126: Instrument Panel Overview
Instrument Panel Overview...
Page 127 The main components of the instrument panel are listed here: A. Outlet Adjustment on page 3-23. B. Remote Trunk Release Button. See Trunk on page 2-12. C. Turn Signal/Multifunction Lever on page 3-7. D. Instrument Panel Cluster on page 3-25. E.
Page 128: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers let you warn others that you have a problem. The hazard warning ﬂasher button is located on top of the steering column. : Press to make the front and rear turn signal lamps ﬂash on and off.
Page 129: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane Change Signals : Headlamp High/Low-Beam Changer : Windshield Wipers : Windshield Washer Flash-to-Pass. For information on the headlamps, see Exterior Lamps on page 3-12.
Page 130: Headlamp High/Low-Beam Changer
Turn Signal On Chime If either one of the turn signals are left on and the vehicle has been driven more than 3/4 mile (1.2 km), a chime will sound. Headlamp High/Low-Beam Changer To change the headlamps from low beam to high beam, push the turn signal/multifunction lever away from you.
Page 131: Windshield Washer
Windshield Washer At the top of the multifunction lever, there is a paddle with the windshield washer symbol on it. Push the paddle to spray washer ﬂuid on the windshield. The wipers run for several sweeps and then either stop or return to the preset speed. The ignition key must be in ACC/ACCESSORY or ON/RUN for this to work.
Page 132: Setting Cruise Control
The cruise control buttons are located on left side of the steering wheel. (On/Off): Press to turn cruise control on and off. The indicator is lit when cruise control is on. + RES (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed. SET–...
Page 133 Resuming a Set Speed If cruise control is set at a desired speed and the brakes are applied, this shuts off the cruise control. However, it does not need to be reset. Once your vehicle reaches a speed of about 25 mph (40 km/h) or more, press the +RES button on the steering wheel.
Page 134: Exterior Lamps
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. When going downhill, you might have to brake or shift to a lower gear to keep your speed down.
Page 135 The exterior lamps control has four positions: (Off): Turns off the automatic headlamps and daytime running lamps (DRL). Turning the headlamp control to the off position again will turn the automatic headlamps or DRL back on. For vehicles ﬁrst sold in Canada, the off position only works when the vehicle is shifted into the P (Park) position.
Page 136: Daytime Running Lamps (Drl)/Automatic Headlamp System
Daytime Running Lamps (DRL)/ Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. Fully functional daytime running lamps are required on all vehicles ﬁrst sold in Canada. The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met:...
Page 137: Instrument Panel Brightness
Instrument Panel Brightness (Instrument Panel Brightness): The knob with this symbol on it is located next to the exterior lamps control to the left of the steering wheel. Push the knob in all the way until it extends out and then turn the knob clockwise or counterclockwise to brighten or dim the lights.
Page 138: Delayed Entry Lighting
Delayed Entry Lighting Delayed entry lighting illuminates the interior for a period of time after all the doors have been closed. The ignition must be off for delayed entry lighting to work. Immediately after all the doors have been closed, the delayed entry lighting feature continues to work until one of the following occurs: •...
Page 139: Reading Lamps
Reading Lamps The vehicle has reading lamps that also act as the dome lamp. Press the button to turn them on and off. Mirror Reading Lamps The vehicle has reading lamps on the rearview mirror. Push the button to turn the reading lamps on and off. Electric Power Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge.
Page 140: Battery Run-Down Protection
Battery Run-Down Protection This feature helps prevent the battery from being drained, if the interior courtesy lamps, reading/map lamps, visor vanity lamps or trunk lamp are accidentally left on. If any of these lamps are left on, they automatically turn off after 10 minutes, if the ignition is off.
Page 141: Ashtray(S) And Cigarette Lighter
Certain accessory plugs may not be compatible to the accessory power outlet and could result in blown vehicle and adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the power accessory plugs. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should.
Page 142: Climate Controls
Climate Controls Climate Control System The heating, cooling, defrost, defog and ventilation can be controlled with this system. For vehicles with heated seats, see Heated Seats on page 1-6. A. Fan Control E. Air Conditioning B. Outside Air F. Heated Seats C.
Page 143 (Floor): Air is directed to the ﬂoor outlets, with some of the air directed to the windshield and side window outlets. In this mode, the system automatically selects outside air. (Defog): This mode clears the windshield of fog or moisture. Air is directed equally to the windshield and the ﬂoor outlets.
Page 144: Rear Window Defogger
Using these settings together for long periods of time may cause the air inside the vehicle to become too dry. To prevent this from happening, after the air inside the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so a small amount of water may drip under the vehicle while idling or after turning off the engine.
Page 145: Outlet Adjustment
Outlet Adjustment Use the thumbwheel located below or to the side of the outlet, to change the direction of the air ﬂow. Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into the vehicle.
Page 146: Warning Lights, Gages, And Indicators
4. Remove the air inlet grille retainers. 5. Lift the air inlet grille and disconnect the washer hose at the quick-connect. 6. Remove the air inlet grille. 7. Remove the water deﬂector plate. 8. Remove the old passenger compartment air ﬁlter. 9.
Page 147: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel has been used and many other things needed to drive safely and economically. United States Uplevel shown, Base and Canada similar 3-25...
Page 148: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven in either miles (used in the United States) or in kilometers (used in Canada). This vehicle has a tamper-resistant odometer.
Page 149: Safety Belt Reminders
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more.
Page 150: Airbag Readiness Light
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 1-57.
Page 151: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-65 for important safety information. The instrument panel has a passenger airbag status indicator. United States When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 152: Charging System Light
Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer.
Page 153: Antilock Brake System (Abs) Warning Light
When the ignition is on, the brake system warning light also comes on when the parking brake is set. The light stays on if the parking brake does not fully release. If it stays on after the parking brake is fully released, it means the vehicle has a brake problem.
Page 154: Traction Control System (Tcs) Warning Light
If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes. If the regular brake system warning light is also on, the vehicle does not have antilock brakes and there is a problem with the regular brakes.
Page 155: Electronic Stability Control Indicator Light
Electronic Stability Control Indicator Light This light comes on brieﬂy while the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light will then go off. This light can come on after the vehicle is ﬁrst driven and the STABILITRAK NOT READY message appears in the Driver Information Center (DIC).
Page 156: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light This light comes on brieﬂy while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Page 157: Tire Pressure Light
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on brieﬂy when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is signiﬁcantly underinﬂated.
Page 158: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It ensures that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 159 This light comes on during a malfunction in one of two ways: Light Flashing: A misﬁre condition has been detected. A misﬁre increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required. To prevent more serious damage to the vehicle: •...
Page 160: Emissions Inspection And Maintenance Programs
If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to ﬁx any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control...
Page 161: Maintenance Schedule
Oil Pressure Light CAUTION: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Page 162: Fog Lamp Light
Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 3-14 for more information. Cruise Control Light The cruise control light comes on whenever the cruise control is set.
Page 163: Fuel Gage
Fuel Gage United States When the ignition is on, the fuel gage indicates about how much fuel is left in the fuel tank. An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about.
Page 164: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle has a Driver Information Center (DIC). All messages will appear in the DIC display located below the speedometer in the instrument panel cluster. The DIC buttons are located on the instrument panel, to the right of the instrument panel cluster. The DIC comes on when the ignition is on.
Page 165 (Vehicle Information): Press this button to display the oil life, units, tire pressure readings, compass zone and compass calibration on vehicles with this feature, and Remote Keyless Entry (RKE) transmitter programming. (Customization): Press this button to customize the feature settings on your vehicle. See DIC Vehicle Customization on page 3-57 for more information.
Page 166 If the retro-active reset feature is activated after the vehicle is started, but before it begins moving, the display will show the number of miles (mi) or kilometers (km) that were driven during the last ignition cycle. Fuel Range Press the trip/fuel button until FUEL RANGE displays. This display shows the approximate number of remaining miles (mi) or kilometers (km) the vehicle can be driven without refueling.
Page 167 If your vehicle has the Active Fuel Management™ feature, an Active Fuel Management™ indicator will display on the right side of the DIC, while INST ECONOMY displays on the left side. Active Fuel Management™ allows the engine to operate on either all or half of its cylinders, depending on your driving demands.
Page 168: Tire Pressure
Remember, you must reset the OIL LIFE yourself after each oil change. It will not reset itself. Also, be careful not to reset the OIL LIFE accidentally at any time other than when the oil has just been changed. It cannot be reset accurately until the next oil change. To reset the engine oil life system, see Engine Oil Life System on page 5-20.
Page 169: Dic Compass
Relearn Remote Key To access this display, the vehicle must be in P (Park). This display allows you to match the Remote Keyless Entry (RKE) transmitter to your vehicle. This procedure will erase all previously learned transmitters. Therefore, they must be relearned as additional transmitters. To match an RKE transmitter to your vehicle: 1.
Page 170: Compass Calibration
To adjust for compass variance, use the following procedure: Compass Variance (Zone) Procedure 1. Do not set the compass zone when the vehicle is moving. Only set it when the vehicle is in P (Park). Press the vehicle information button until PRESS TO CHANGE COMPASS ZONE displays.
Page 171: Dic Warnings And Messages
To calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, make sure the compass zone is set to the variance zone in which the vehicle is located. See “Compass Variance (Zone) Procedure” earlier in this section. Do not operate any switches such as window, sunroof, climate controls, seats, etc.
Page 172: Check Tire Pressure
AUTOMATIC LIGHT CONTROL ON This message displays when the automatic headlamps are turned on. See Exterior Lamps on page 3-12 for more information. BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system starts reducing certain features of the vehicle that you may be able to notice.
Page 173: Engine Overheated Stop Engine
DRIVER DOOR OPEN This message displays when the driver door is not closed properly. Make sure that the door is closed completely. ENGINE HOT A/C (Air Conditioning) OFF This message displays when the engine coolant becomes hotter than the normal operating temperature.
Page 174: Oil Pressure Low Stop Engine
ENGINE POWER IS REDUCED This message displays when the vehicle’s engine power is reduced. Reduced engine power can affect the vehicle’s ability to accelerate. If this message is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven.
Page 175: Service Air Bag
PASSENGER DOOR OPEN This message displays when the front passenger door is not closed properly. Make sure that the door is closed completely. REMOTE KEY LEARNING ACTIVE This message displays while you are matching a Remote Keyless Entry (RKE) transmitter to your vehicle. See “Matching Transmitter(s) to Your Vehicle”...
Page 176: Service Brake System
SERVICE BRAKE SYSTEM This message displays when service is required on the brake system. Have the brake system serviced by your dealer/retailer as soon as possible. The brake system warning light also appears on the instrument panel cluster when this message appears on the DIC. See Brake System Warning Light on page 3-30.
Page 177: Service Transmission
SERVICE TRACTION CONTROL If your vehicle has the Traction Control System (TCS), this message displays when the system is not functioning properly. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-32. See Traction Control System (TCS) on page 4-8 for more information.
Page 178: Trunk Open
TIRE LEARNING ACTIVE On vehicles with the Tire Pressure Monitor System (TPMS), this message displays when the TPMS is re-learning the tire positions on your vehicle. The tire positions must be re-learned after rotating the tires or after replacing a tire or sensor. See Tire Inspection and Rotation on page 5-67, Tire Pressure Monitor System on page 5-62, and Inﬂation - Tire Pressure on page 5-60 for more...
Page 179: Dic Vehicle Customization
WASHER FLUID LOW ADD FLUID This message displays when the windshield washer ﬂuid is low. Fill the windshield washer reservoir as soon as possible. See Engine Compartment Overview on page 5-14 for the location of the windshield washer reservoir. Also, see Windshield Washer Fluid on page 5-35 for more information.
Page 180: Display Language
DISPLAY LANGUAGE This feature allows you to select the language in which the DIC messages will appear. Press the customization button until the DISPLAY LANGUAGE screen appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Page 181: Remote Door Lock
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if any of the doors are open. See Remote Keyless Entry (RKE) System Operation on page 2-5 for more information.
Page 182: Exit Lighting
EXIT LIGHTING This feature allows you to select the amount of time you want the exterior lamps to remain on when it is dark enough outside. This happens after the key is turned from ON/RUN to LOCK/OFF. Press the customization button until EXIT LIGHTING appears on the DIC display.
Page 183: Remote Start
CHIME VOLUME This feature allows you to select the volume level of the chime. Press the customization button until CHIME VOLUME appears on the DIC display. Press the set/reset button once to access the settings for this feature. Then press the customization button to scroll through the following settings: NORMAL: The chime volume will be set to a normal...
Page 184: Factory Settings
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Page 185: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 186: Setting The Clock
Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player This radio has a button for setting the time. To set the time: 1. Press the button until the hour begins ﬂashing on display. Press a second time and the minutes begin ﬂashing on display.
Page 187 Six-Disc CD (MP3) Player This type of radio has a MENU button instead of the clock button to set the time and date. To set the time and date, follow these instructions: 1. Turn the radio on. 2. Press the MENU button. 3.
Page 188: Radio(S)
Radio(s) Radio with CD (Base) 3-66 Radio with CD (MP3) shown, Radio with Six-Disc CD (MP3) similar The vehicle has one of these radios as its audio system.
Page 189: Playing The Radio
Radio Data System (RDS) The radio may have the Radio Data System (RDS) feature. RDS is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display.
Page 190: Finding A Station
Finding a Station BAND: Press to switch between FM1, FM2, AM, or XM™. The selection displays. (Tune): Turn to select radio stations. © ¨ SEEK : Press to go to the previous or the next station and stay there. To scan stations, press and hold either arrow for a few seconds until the radio beeps once.
Page 191 FAV (Favorites): Press to go through up to six pages of favorites, each having six favorite stations available per page. Each page of favorites can contain any combination of AM, FM, or XM stations. To store a station as a favorite: 1.
Page 192: Adjusting The Speakers (Balance/Fade)
To return to the manual mode, press until Manual displays or start to manually adjust the bass and depending on the radio, midrange, or treble by pressing the knob. Adjusting the Speakers (Balance/Fade) BAL/FADE (Balance/Fade): To adjust balance or fade, press the if the radio has this symbol, or knob until the speaker control tabs display.
Page 193: Radio Messages
Undesired XM categories can be removed through the setup menu. To remove an undesired category: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the XM CAT tab. 3. Turn the knob to display the category to be removed.
Page 194: Playing A Cd
Radio Messages for XM™ Only See XM Radio Messages on page 3-81 later in this section for further detail. Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD should begin playing. If the ignition or radio is turned off while a CD in the player it stays in the player.
Page 195 EJECT: For the Radio with a Single CD player, press to eject the CD. If the CD is not removed, after several seconds, the CD automatically pulls back into the player. For the Radio with a Six-Disc CD player, press and release to eject the CD that is currently playing.
Page 196 To use random on a radio with a Six-Disc CD player: 1. Press the CD/AUX button, press and hold A beep sounds and Load All Discs displays. Insert one or more discs partway into the slot of the CD player. 2.
Page 197 Care of the CD Player Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
Page 198: Using The Auxiliary Input Jack
Using the Auxiliary Input Jack The radio system has an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. However, an external audio device such as an iPod, laptop computer, MP3 player, CD changer, or cassette tape player, etc.
Page 199: Using An Mp3
Using an MP3 MP3 CD-R or CD-RW Disc The radio may have MP3 capability. With this feature, the radio plays MP3 ﬁles that were recorded on a CD-R or CD-RW disc. Song title, artist name, and album can display when ﬁles are recorded using ID3 tags version 1 and 2.
Page 200 • Make sure playlists have a .mp3 or .wpl extension (other ﬁle extensions might not work). • Minimize the length of the ﬁle, folder or playlist names. Long ﬁle, folder, or playlist names, or a combination of a large number of ﬁles and folders, or playlists can cause the player to be unable to play up to the maximum number of ﬁles, folders, playlists, or sessions.
Page 201 Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: • Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist.
Page 202 (Next Folder): Press the pushbutton positioned under the Folder tab to go to the ﬁrst track in the next folder. REV (Reverse): Press and hold to reverse playback quickly within an MP3 ﬁle. Sound is heard at a reduced volume. Release this button to resume playing the ﬁle.
Page 203: Xm Radio Messages
songs from the current album begins to play. Once all songs from that album have played, the player moves to the next album in alphabetical order on the CD and begins playing MP3 ﬁles from that album. To exit music navigator mode, press the pushbutton below the Back tab to return to normal MP3 playback.
Page 204: Bluetooth
XM Radio ID: If tuned to channel 0, this message alternates with the XM™ Radio 8 digit radio ID label. This label is needed to activate the service. Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer.
Page 205: Bluetooth Controls
Bluetooth Controls Use the buttons located on the steering wheel to operate the in-vehicle Bluetooth system. See Audio Steering Wheel Controls on page 3-94 for more information. (Push To Talk): Press to answer incoming calls, to conﬁrm system information, and to start speech recognition.
Page 206: Pairing A Phone
Pairing a Phone 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Pair”. The system responds with instructions and a four digit PIN number.
Page 207: Storing Name Tags
Linking to a Different Phone 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds with “Bluetooth ready” followed by a tone. 3. Say “Change phone”. The system responds with “Please wait while I search for other phones”.
Page 208 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>. Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. •...
Page 209: Deleting Name Tags
Deleting Name Tags The system uses the following commands to delete name tags: • Delete • Delete all name tags Using the Delete Command The delete command allows speciﬁc name tags to be deleted. To use the delete command: 1. Press and hold for two seconds.
Page 210: Making A Call
Making a Call Calls can be made using the following commands: • Dial • Digit Dial • Call • Re-dial Using the Dial Command 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2.
Page 211: Receiving A Call
Using the Call Command 1. Press and hold for two seconds. The system responds with “Ready” followed by a tone. 2. Say “Call”. The system responds with “Call using <phone name>. Please say the name tag” followed by a tone. 3.
Page 212: Call Waiting
Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. • Press to answer an incoming call when another call is active. The original call is placed on hold. • Press again to return to the original call.
Page 213: Transferring A Call
Transferring a Call Audio can be transferred between the in-vehicle Bluetooth system and the cell phone. To Transfer Audio to the Cell Phone During a call with the audio in the vehicle: 1. Press . The system responds with “Ready” followed by a tone.
Page 214 Sending a Number During a Call 1. Press . The system responds with “Ready” followed by a tone. 2. Say “Dial”. The system responds with “Say a number to send tones” followed by a tone. 3. Say the number to send. •...
Page 215: Theft-Deterrent Feature
Clearing the System Unless information is deleted out of the in-vehicle Bluetooth system, it will be retained indeﬁnitely. This includes all saved name tags in the phonebook and phone pairing information. For information on how to delete this information, see the above sections on Deleting a Paired Phone and Deleting Name Tags.
Page 216: Audio Steering Wheel Controls
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. (Next): Press to go to the next radio station stored as a favorite, or the next track if a CD is playing. (Previous/End): Press to go to the previous radio station stored as a favorite, the next track if a CD is playing, to reject an incoming call, or end a current call.
Page 217: Radio Reception
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 218: Backglass Antenna
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Page 219: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-5 Braking in Emergencies ...4-6 Electronic Stability Control (ESC) ...4-6 Traction Control System (TCS) ...4-8 Steering ...4-9 Off-Road Recovery ...4-11...
Page 220: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 221: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 222: Braking
Braking See Brake System Warning Light on page 3-30. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Page 223: Antilock Brake System (Abs)
Antilock Brake System (ABS) The vehicle might have the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. If the vehicle has ABS, this warning light on the instrument panel cluster comes on brieﬂy when the vehicle is started.
Page 224: Braking In Emergencies
Braking in Emergencies At some time, nearly every driver gets into a situation that requires hard braking. If the vehicle has ABS, it allows the driver to steer and brake at the same time. However, if the vehicle does not have ABS, the ﬁrst reaction — to hit the brake pedal hard and hold it down —...
Page 225 This light will ﬂash on the instrument panel cluster when the ESC system is both on and activated. You may also feel or hear the system working; this is normal. When the light is on solid and the SERVICE STABILITRAK message is displayed, the system will not assist the driver in maintaining directional control of the vehicle.
Page 226: Traction Control System (Tcs)
If the problem does not clear after restarting the vehicle, you should see your dealer/retailer for service. See DIC Warnings and Messages on page 3-49 for more information. Adding non-dealer/non-retailer accessories can affect your vehicle’s performance. See Accessories and Modiﬁcations on page 5-3 for more information. Traction Control System (TCS) The vehicle may have a Traction Control System (TCS) that limits wheel spin.
Page 227: Steering
Turn the system off if the vehicle gets stuck in sand, mud or snow and rocking the vehicle is required. See Rocking Your Vehicle to Get It Out on page 4-20 and If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 4-19 for more information.
Page 228: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 229: Off-Road Recovery
Off-Road Recovery The vehicle’s right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that the vehicle straddles the edge of the pavement.
Page 230 Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle’s three control systems.
Page 231: Driving At Night
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: • Drive defensively. • Do not drink and drive. •...
Page 232: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water. CAUTION: Wet brakes can cause crashes.
Page 233: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 234: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 235: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 236 Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-8. To get help and keep everyone in the vehicle safe: •...
Page 237: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Page 238: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear, spinning the wheels as little as possible. To prevent transmission wear, wait until the wheels stop spinning before shifting gears.
Page 239 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). The Tire and Loading Information label lists the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 240 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 241 Example 1 Item Description Maximum Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Maximum Vehicle...
Page 242 Example 3 Item Description Maximum Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight 200 lbs (91 kg) × 5 = Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight and seating positions.
Page 243 Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. If the vehicle is going to carry a heavy load, spread it out. See “Steps for Determining Correct Load Limit” earlier in this section. CAUTION: Do not load the vehicle any heavier than the Gross Vehicle Weight Rating (GVWR), or...
Page 244: Towing
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 7-8. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motorhome, see “Recreational Vehicle Towing”...
Page 245: Dinghy Towing
Dinghy Towing Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground.
Page 246: Towing A Trailer
6. Secure the vehicle to the dolly following the manufacturer’s instructions. 7. Release the parking brake only after the vehicle being towed is ﬁrmly attached to the towing vehicle. 8. Turn the ignition to LOCK/OFF and remove the key. Towing a Trailer CAUTION: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is...
Page 247: Pulling A Trailer
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Page 248: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 249: Safety Chains
Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why the right hitch is needed. Here are some rules to follow: • The rear bumper on the vehicle is not intended for hitches.
Page 250: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
Page 251: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer The arrows on the instrument panel ﬂash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps also ﬂash, telling other drivers the vehicle is turning, changing lanes or stopping. When towing a trailer, the arrows on the instrument panel ﬂash for turns even if the bulbs on the trailer are burned out.
Page 252: Engine Cooling When Trailer Towing
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4.
Page 253: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-6 Fuel E85 (85% Ethanol) ...5-8...
Page 254 Section 5 Tire Pressure Monitor Operation ...5-63 Tire Inspection and Rotation ...5-67 When It Is Time for New Tires ...5-68 Buying New Tires ...5-69 Different Size Tires and Wheels ...5-71 Uniform Tire Quality Grading ...5-71 Wheel Alignment and Tire Balance ...5-73 Wheel Replacement ...5-73 Tire Chains ...5-74 If a Tire Goes Flat ...5-75...
Page 255: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like antilock brakes,...
Page 256: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 257: Adding Equipment To The Outside Of The Vehicle
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-15. Adding Equipment to the Outside of the Vehicle Things added to the outside of the vehicle can affect the airﬂow around it.
Page 258: Gasoline Speciﬁcations
If the vehicle has the 5.3L V8 engine (VIN Code C), use premium unleaded gasoline with a posted octane rating of 91 or higher. You can also use regular unleaded gasoline rated at 87 octane or higher, but the vehicle’s acceleration could be slightly reduced, and you might notice a slight audible knocking noise, commonly referred to as spark knock.
Page 259 However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. To help keep fuel injectors and intake valves clean, or if the vehicle experiences problems due to dirty injectors or valves, look for gasoline that is advertised as TOP TIER Detergent Gasoline.
Page 260: Fuel E85 (85% Ethanol)
Fuel E85 (85% Ethanol) The 8th digit of the Vehicle Identiﬁcation Number (VIN) shows the code letter or number that identiﬁes the vehicle’s engine. The VIN is at the top left of the instrument panel. See Vehicle Identiﬁcation Number (VIN) on page 5-96. If the vehicle has the 3.5L V6 engine (VIN Code K) or the 3.9L V6 engine (VIN Code M), you can use either unleaded gasoline or ethanol fuel containing up to 85%...
Page 261: Fuels In Foreign Countries
If you do switch fuels, it is recommended that you add as much fuel as possible — do not add less than three gallons (11 L) when refueling. You should drive the vehicle immediately after refueling for at least seven miles (11 km) to allow the vehicle to adapt to the change in ethanol concentration.
Page 262: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling.
Page 263 CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather.
Page 264: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 265: Hood Release
Hood Release To open the hood, do the following: 1. Pull the interior hood release handle with this symbol on it. It is located to the left of the parking brake pedal. 2. Then go to the front of the vehicle and release the secondary hood latch, located near the center of the hood front, by pushing the latch to the right.
Page 266: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.5L V6 engine (3.9L V6 similar), here is what you will see: 5-14...
Page 267 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35. B. Battery. See Battery on page 5-40. C. Underhood Fuse Block. See Underhood Fuse Block on page 5-98. D. Remote Positive (+) Terminal. See Jump Starting on page 5-40.
Page 268 When you open the hood on the 5.3L V8 engine, here is what you will see: 5-16...
Page 269: Engine Oil
A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-35. B. Battery. See Battery on page 5-40. C. Underhood Fuse Block. See Underhood Fuse Block on page 5-98. D. Remote Positive (+) Terminal. See Jump Starting on page 5-40.
Page 270: When To Add Engine Oil
When to Add Engine Oil V6 Engine V8 Engine If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-101.
Page 271: Cold Temperature Operation
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Page 272: Engine Oil Life System
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system ﬂushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 273: Engine Air Cleaner/Filter
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL SOON message being turned on, reset the system.
Page 274: How To Inspect The Engine Air Cleaner/ Filter
When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 6-4 for more information. If you are driving in dusty/dirty conditions, inspect the ﬁlter at each engine oil change.
Page 275 2. Push the ﬁlter cover housing toward the engine. 3. Pull out the ﬁlter. 4. Inspect or replace the engine air cleaner/ﬁlter. 5. To reinstall the cover, position the tabs through the hinges on the housing. 6. Push the cover tabs on top of the housing to lock the cover in place.
Page 276: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check and Change Automatic Transmission Fluid A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 6-6, and be sure to use the transmission ﬂuid listed in Recommended Fluids and Lubricants on page 6-12.
Page 277 Then, without shutting off the engine, follow these steps: 1. Pull out the dipstick and wipe it with a clean rag or paper towel. The transmission ﬂuid dipstick handle is the black loop with this symbol on it. It is located near the rear of the engine compartment.
Page 278: Cooling System
How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the cross-hatched area on the dipstick.
Page 279 5.3L V8 Engine A. Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Page 280: Engine Coolant
Engine Coolant The cooling system in the vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst. The following explains the cooling system and how to check and add coolant when it is low.
Page 281: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the COLD FILL line, add a 50/50 mixture of clean, ®...
Page 282: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 283: Pressure Cap
4. Then ﬁll the coolant recovery tank to the COLD FILL line. 5. Install the coolant recovery tank cap and the pressure cap. After a day or two of driving, when the engine is cold, check the coolant level in the recovery tank.
Page 284: If Steam Is Coming From The Engine Compartment
If you do decide to lift the hood, make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fans are running. If the engine is overheating, both fans should be running. If they are not, do not continue to run the engine and have the vehicle serviced.
Page 285: If No Steam Is Coming From The Engine Compartment
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: •...
Page 286: Overheated Engine Protection Operating Mode
Overheated Engine Protection Operating Mode This emergency operating mode allows your vehicle to be driven to a safe place in an emergency situation. If an overheated engine condition exists, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage. In this mode, you will notice a signiﬁcant loss in power and engine performance.
Page 287: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 288: Adding Washer Fluid
Adding Washer Fluid A WASHER FLUID LOW ADD FLUID message will be displayed on the Driver Information Center (DIC) when you need to add windshield washer ﬂuid to your vehicle. See DIC Warnings and Messages on page 3-49 for more information.
Page 289: Brakes
Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT 3 brake ﬂuid. See Engine Compartment Overview on page 5-14 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down: •...
Page 290 What to Add Use only new DOT 3 brake ﬂuid from a sealed container. See Recommended Fluids and Lubricants on page 6-12. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir.
Page 291: Brake Adjustment
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 292: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced —...
Page 293 CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Page 294 Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty. Always turn off the radio and other accessories when jump starting the vehicle. 3.
Page 295 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 296 7. Do not let the other end touch metal. Connect it to the positive (+) terminal location of the vehicle with the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative (−) cable to the negative (−) terminal location of the vehicle with the good battery.
Page 297: Headlamp Aiming
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 298: Headlamps, Front Turn Signal, Sidemarker, And Parking Lamps
Headlamps, Front Turn Signal, Sidemarker, and Parking Lamps A. Sidemarker C. High-Beam B. Low-Beam Headlamp Headlamp D. Parking/Turn Signal Lamp 5-46 To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-13. 2. Remove the screw from the headlamp assembly.
Page 299 3. Pull up on the plastic headlamp retainer and remove it. 4. Pull the headlamp assembly away from the vehicle and remove the electrical connector. 5. Remove the round dust caps to gain access to the bulbs. 6. Turn the old bulb counterclockwise and remove it from the retaining ring by pulling it away from the headlamp.
Page 300 12. Push down on the plastic headlamp retainer to 13. Reinstall the screw from the headlamp assembly. reinstall it. 5-48...
Page 301: Taillamps, Turn Signal, Sidemarker, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps A. Rear Sidemarker Lamp B. Back-up Lamp C. Stoplamp/Taillamp/Turn Signal To replace one of these bulbs: 1. Open the trunk. See Trunk on page 2-12. 2. Remove the convenience net. Unhook the net from the upper wing nut.
Page 302 5. Turn the two hex nuts counterclockwise to remove them. 6. Pull out the taillamp assembly and disconnect the wiring harness. 7. Turn the bulb socket counterclockwise to remove it. 8. Pull the old bulb straight out to remove it. 9.
Page 303: License Plate Lamp
License Plate Lamp To replace one of these bulbs: 1. Turn the lamp assembly counterclockwise and pull the lamp assembly out of the connector. 2. Pull the old bulb from the lamp assembly, keeping the bulb straight as you pull it out. 3.
Page 304 To remove and replace the wiper blade element do the following: 1. The wiper blade element has two notches at one end which are engaged by the bottom claw set of the wiper blade. At the notched end of the wiper blade, pull the wiper blade element from the wiper blade assembly.
Page 305: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer.
Page 306: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example 5-54 (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 307 (D) Tire Identiﬁcation Number (TIN) letters and numbers following DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 308 (B) Tire Ply Material The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identiﬁcation Number (TIN) and numbers following the DOT (Department of Transportation) code is the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured.
Page 309: Tire Terminology And Deﬁnitions
(C) Aspect Ratio A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide.
Page 310 Cold Tire Pressure The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inﬂation - Tire Pressure on page 5-60. Curb Weight The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but...
Page 311 Maximum Loaded Vehicle Weight curb weight, accessory weight, vehicle capacity weight, and production options weight. Normal Occupant Weight The number of occupants a vehicle is designed to seat multiplied by 150 lbs (68 kg). See Loading the Vehicle on page 4-20. Occupant Distribution Designated seating positions.
Page 312: Inﬂation - Tire Pressure
UTQGS (Uniform Tire Quality Grading Standards) A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-71.
Page 313: How To Check
A vehicle speciﬁc Tire and Loading Information label is attached to your vehicle. This label shows your vehicle’s original equipment tires and the correct inﬂation pressures for your tires when they are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity.
Page 314: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer...
Page 315: Tire Pressure Monitor Operation
Federal Communications Commission (FCC) and Industry and Science Canada The Tire Pressure Monitor System (TPMS) operates on a radio frequency and complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
Page 316: Tpms Malfunction Light And Message
Using the DIC, tire pressure levels can be viewed by the driver. For additional information and details about the DIC operation and displays see DIC Operation and Displays on page 3-42 and DIC Warnings and Messages on page 3-49. The low tire pressure warning light may come on in cool weather when the vehicle is ﬁrst started, and then turn off as you start to drive.
Page 317: Tpms Sensor Matching Process
• One or more TPMS sensors are missing or damaged. The DIC message and the TPMS malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer/retailer for service. •...
Page 318 You have two minutes to match the ﬁrst tire/wheel position, and ﬁve minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the ﬁrst tire and wheel, or more than ﬁve minutes to match all four tire and wheel positions the matching process stops and you need to start over.
Page 319: Tire Inspection And Rotation
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle’s tires, including the spare tire, for signs of wear or damage. See When It Is Time for New Tires on page 5-68 for more information. Tires should be rotated every 5,000 to 8,000 miles (8 000 to 13 000 km).
Page 320: When It Is Time For New Tires
Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 5-63. Make certain that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Speciﬁcations on page 5-101. CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
Page 321: Buying New Tires
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
Page 322 GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Page 323: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Page 324 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 325: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Page 326: Tire Chains
Used Replacement Wheels CAUTION: Putting a used wheel on the vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 327: If A Tire Goes Flat
CAUTION: (Continued) Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions. To help avoid damage to your vehicle, drive slowly, readjust, or remove the device if it is contacting your vehicle, and do not spin your wheels.
Page 328: Changing A Flat Tire
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
Page 329: Removing The Spare Tire And Tools
CAUTION: (Continued) To be even more certain the vehicle will not move, you should put blocks at the front and rear of the tire farthest away from the one being changed. That would be the tire, on the other side, at the opposite end of the vehicle.
Page 330 6. Turn the nut holding the jack counterclockwise and The tools you will need to change a tire include the remove it. Then remove the jack and wrench. jack (A), extension and protection guide (B), and wheel wrench (C). 5-78...
Page 331: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire This vehicle may have aluminum wheels with exposed wheel nuts. Use the wheel wrench to loosen all the wheel nuts. Do not remove them yet. Or, this vehicle may have steel wheels with plastic covers.
Page 332 3. For all wheel types, ﬁnd the jacking location using the diagram above and the corresponding jacking notches located on the bottom side of the plastic molding. The notches in the plastic molding are marked with a triangle shape to help you ﬁnd them. The front location is about 7.0 inches (17.7 cm) from the rear edge of the front wheel well.
Page 333 CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a ﬂat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack.
Page 334 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 335 9. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut clockwise by hand until the wheel is held against the hub. 10. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. 5-83...
Page 336 CAUTION: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 337: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 338 A. Cover B. Retainer C. Compact Spare Tire D. Wing Nut E. Jack F. Wheel Wrench G. Extension Protector H. Foam Holder I. Bolt Screw Compact Spare Tire 5-86...
Page 339 A. Retainer B. Full-Size Flat Tire C. Protective Guide D. Extension Bolt Screw E. Wing Nut F. Jack G. Wheel Wrench H. Foam Holder I. Bolt Screw Full-Size Flat Tire 5-87...
Page 340: Compact Spare Tire
Compact Spare Tire CAUTION: Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.
Page 341: Appearance Care
Appearance Care Interior Cleaning The vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from the upholstery.
Page 342: Fabric/Carpet
Products that remove odors from the vehicle’s upholstery and clean the vehicle’s glass can be obtained from your dealer/retailer. Do not clean the vehicle using: • A knife or any other sharp object to remove a soil from any interior surface. •...
Page 343: Leather
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness ﬁrst. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Page 344: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips If dirt and/or contaminants build up in the glass seals, use a cloth and water to clean the glass seals.
Page 345: Cleaning Exterior Lamps/Lenses
Dry the ﬁnish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle. Avoid using high pressure washes closer than 12 inches (30 cm) to the surface of the vehicle.
Page 346: Windshield And Wiper Blades
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer ﬂuid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking.
Page 347: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Page 348: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for the vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 349: Headlamp Wiring
Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have the headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools.
Page 350: Underhood Fuse Block
Fuses AIRBAG Airbags Ampliﬁer Auxiliary Outlets CNSTR Canister DR/LCK Door Locks HTD/SEAT Heated Seats 5-98 PWR/MIR PWR/SEAT PWR/WNDW S/ROOF TRUNK TRUNK Underhood Fuse Block Usage The underhood fuse block is located in the engine compartment. See Engine Compartment Overview on page 5-14 for more information on location.
Page 351 Fuses Usage A/C CMPRSR Air Conditioning Compressor Antilock Brake System (ABS) ABS MTR 1 Motor 1 ABS MTR 2 ABS Motor 2 AIR PUMP Air Pump AIR SOL Air Injection Reactor Solenoid AIRBAG/ Airbag, Display DISPLAY AUX PWR Auxiliary Power BATT 1 Battery 1 BATT 2...
Page 352 Fuses ETC/ECM Electronic Throttle Control, ECM FAN 1 Cooling Fan 1 FAN 2 Cooling Fan 2 FOG LAMPS Fog Lamps (If Equipped) FUEL/PUMP Fuel Pump HDLP MDL Headlamp Module HORN Horn HTD MIR Heated Mirror INJ 1 Injector 1 INJ 2 Injector 2 INT LIGHTS Interior Lamps...
Page 353: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Automatic Transmission Cooling System Including Reservoir 3.5L V6, 3.5L and 3.9L V6 Flexible Fuel Engines 5.3L V8 Engine Engine Oil with Filter 3.5L V6, 3.5L and 3.9L V6 Flexible Fuel Engines...
Page 354 Application Fuel Tank 3.5L Engine (with NU6 emissions) 3.5L Engine (without NU6 emissions) 3.9L and 5.3L Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual. Recheck ﬂuid level after ﬁlling. Engine 3.5L V6 3.5L Flexible Fuel V6...
Page 355 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 356: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 357: Using The Maintenance Schedule
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
Page 358: Scheduled Maintenance
The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-13. When the vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Page 359 Change engine oil and ﬁlter. See Engine Oil on page 5-17. Reset oil life system. See Engine Oil Life System on page 5-20. An Emission Control Service. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-21.
Page 360: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 361: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 362: Engine Oil Level Check
(h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 363: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-28. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer ﬂuid reservoir and add the proper ﬂuid if necessary.
Page 364: Ignition Transmission Lock Check
Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface.
Page 365: Underbody Flushing Service
Parking Brake and Automatic Transmission P (Park) Mechanism Check CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 366: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 367: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter 3.5L V6, 3.5L and 3.9L V6 Flexible Fuel Engines 5.3L V8 Engine Passenger Compartment Air Filter Spark Plugs 3.5L V6, 3.5L and 3.9L V6 Flexible Fuel Engines 5.3L V8 Engine...
Page 368: Engine Drive Belt Routing
Engine Drive Belt Routing 5.3L V8 Engine 3.5L V6 and 3.9 V6 Engines 6-14...
Page 369: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 370 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 371 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 372 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 373: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-5 Customer Assistance for Text Telephone (TTY) Users ...7-6 Customer Assistance Offices ...7-6 GM Mobility Reimbursement Program ...7-7 Roadside Assistance Program ...7-8 Scheduling Service Appointments ...7-10 Courtesy Transportation ...7-11 Collision Damage Repair ...7-12 Customer Assistance Information...
Page 374: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Chevrolet. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 375 STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you can ﬁle with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
Page 376 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/ Arbitration Program.
Page 377: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Chevrolet dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 378: Customer Assistance For Text Telephone (Tty) Users
Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P.O.
Page 379: Gm Mobility Reimbursement Program
Overseas — Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 380: Roadside Assistance Program
Roadside Assistance is not a part of the New Vehicle Limited Warranty. Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 381: Services Provided
• Emergency Tow From a Public Road or Highway: Tow to the nearest Chevrolet dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow.
Page 382: Scheduling Service Appointments
• Trip Interruption Beneﬁts and Assistance: Must be over 250 kilometres from where your trip was started to qualify. General Motors of Canada Limited requires pre-authorization, original detailed receipts, and a copy of the repair orders. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Page 383: Courtesy Transportation
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for vehicles with the Bumper to Bumper (Base Warranty Coverage period in Canada) and extended powertrain, and hybrid speciﬁc warranty in both the U.S.
Page 384: Collision Damage Repair
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer’s shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service. In addition, for U.S.
Page 385: Repair Facility
Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine GM Collision parts are your best choice to ensure that your vehicle’s designed appearance, durability, and safety are preserved.
Page 386: Insuring Your Vehicle
Insuring Your Vehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are signiﬁcant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
Page 387 • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company and policy number, and a general description of the damage to the other vehicle.
Page 388: Reporting Safety Defects
In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P.O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or...
Page 389: Service Manuals
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle.
Page 390: Vehicle Data Recording And Privacy
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Page 391: Onstar
To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
Page 392 ✍ NOTES 7-20...
Page 393 Accessories and Modiﬁcations ... 5-3 Accessory Power ... 2-21 Accessory Power Outlets ... 3-18 Active Fuel Management™ ... 2-23 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-72 Additional Required Services, Scheduled Maintenance ... 6-6 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-96 Air Cleaner/Filter, Engine ...
Page 394 Ashtray ... 3-19 Assistance Program, Roadside ... 7-8 Audio System ... 3-63 Audio Steering Wheel Controls ... 3-94 Setting the Clock ... 3-64 XM™ Satellite Radio Antenna System ... 3-96 Audio System(s) ... 3-66 Audio Systems Radio Reception ... 3-95 Theft-Deterrent Feature ...
Page 395 Canadian Owners ... ii Capacities and Speciﬁcations ... 5-101 Carbon Monoxide Engine Exhaust ... 2-30 Trunk ... 2-12 Winter Driving ... 4-17 Care of Safety Belts ... 5-92 CD, MP3 ... 3-77 Center Console Storage ... 2-43 Center Seat ... 1-10 Chains, Tire ...
Page 396 Cooling System ... 5-26 Courtesy Lamps ... 3-15 Courtesy Transportation ... 7-11 Cruise Control ... 3-9 Cruise Control Light ... 3-40 Cupholders ... 2-43 Customer Assistance ... 7-6 Offices ... 7-6 Text Telephone (TTY) Users ... 7-6 Customer Information Service Publications Ordering Information ... 7-17 Customer Satisfaction Procedure ...
Page 397 E85 Fuel ... 5-8 EDR ... 7-18 Electrical Equipment Add-On Equipment ... 5-96 Electrical System Fuses and Circuit Breakers ... 5-97 Headlamp Wiring ... 5-97 Instrument Panel Fuse Block ... 5-97 Power Windows and Other Power Options ... 5-97 Underhood Fuse Block ... 5-98 Windshield Wiper Fuses ...
Page 398 Fuel ... 5-5 Additives ... 5-6 California Fuel ... 5-6 E85 (85% Ethanol) ... 5-8 Economy Driving ... 4-2 Filling a Portable Fuel Container ... 5-12 Filling the Tank ... 5-10 Fuels in Foreign Countries ... 5-9 Gage ... 3-41 Gasoline Octane ...
Page 399 Highway Hypnosis ... 4-15 Hill and Mountain Roads ... 4-16 Hood Checking Things Under ... 5-12 Release ... 5-13 Horn ... 3-6 How to Wear Safety Belts Properly ... 1-18 Ignition Positions ... 2-20 Infants and Young Children, Restraints ... 1-37 Inﬂation - Tire Pressure ...
Page 400 Lights (cont.) Fog Lamp ... 3-40 Highbeam On ... 3-40 High/Low Beam Changer ... 3-8 Oil Pressure ... 3-39 Passenger Airbag Status Indicator ... 3-29 Safety Belt Reminders ... 3-27 Security ... 3-39 Tire Pressure ... 3-35 Traction Control System (TCS) Warning ... 3-32 Loading Your Vehicle ...
Page 401 Mirrors Automatic Dimming Rearview ... 2-32 Manual Rearview Mirror ... 2-32 Outside Convex Mirror ... 2-33 Outside Heated Mirrors ... 2-33 Outside Power Mirrors ... 2-32 MP3 ... 3-77 Navigation System, Privacy ... 7-19 Convenience ... 2-43 New Vehicle Break-In ... 2-19 Odometer ...
Page 402 Perchlorate Materials Requirements, California ... 5-4 Phone ® Bluetooth ... 3-82 Power Door Locks ... 2-10 Electrical System ... 5-97 Retained Accessory (RAP) ... 2-21 Seat ... 1-5 Steering Fluid ... 5-34 Windows ... 2-15 Pregnancy, Using Safety Belts ... 1-32 Pressure Cap ...
Page 403 Ride Control Systems ... 4-6 Electronic Stability (ESC) ... 4-6 Roadside Assistance Program ... 7-8 Rocking Your Vehicle to Get it Out ... 4-20 Roof Sunroof ... 2-44 Running the Vehicle While Parked ... 2-31 Safety Belt Reminders ... 3-27 Safety Belts Care of ...
Page 404 Shifting Into Park ... 2-27 Signals, Turn and Lane-Change ... 3-7 Spare Tire Compact ... 5-88 Installing ... 5-79 Removing ... 5-77 Storing ... 5-85 Speciﬁcations and Capacities ... 5-101 Speedometer ... 3-26 Split Folding Rear Seat ... 1-10 StabiliTrak Control Indicator Light, Electronic ... 3-33 Start Vehicle, Remote ...
Page 405 Tires (cont.) Inﬂation - Tire Pressure ... 5-60 Inspection and Rotation ... 5-67 Installing the Spare Tire ... 5-79 Pressure Monitor Operation ... 5-63 Pressure Monitor System ... 5-62 Removing the Flat Tire ... 5-79 Removing the Spare Tire and Tools ... 5-77 Sidewall Labeling ...
Page 406 Warning Lights, Gages, and Indicators ... 3-24 Warnings DIC Warnings and Messages ... 3-49 Hazard Warning Flashers ... 3-6 Safety and Symbols ... iii Wheels Alignment and Tire Balance ... 5-73 Different Size ... 5-71 Replacement ... 5-73 When It Is Time for New Tires ... 5-68 Where to Put the Child Restraint ...

Chevrolet 2009 Impala Owner's Manual

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Chevrolet 2009 Impala

Summary of Contents for Chevrolet 2009 Impala