Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Greenlee ES32FML
Summary of Contents for Greenlee ES32FML
- Page 1 OPERATION MANUAL ES32ML ES32FML EBS12ML Battery-powered Micro Cutters Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com 52078039 REV 1 © 2019 Greenlee Tools, Inc. 11/19...
-
Page 2: Table Of Contents
These tools are protected by U.S. Patent No. 6,276,186, 6,401,515, 6,718,870, 7,086,979, and 7,254,982. All specifications are nominal and may change as design improvements occur. Greenlee Tools, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. KEEP THIS MANUAL Greenlee Tools, Inc. -
Page 3: Important Safety Information
This tool is not insulated. When using this unit near energized electrical lines, use proper personal protective equipment. Failure to observe this warning could result in severe injury or death. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... - Page 4 Failure to observe this precaution may result in injury and property damage. Note: Keep all decals clean and legible, and replace when necessary. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070...
-
Page 5: Identification
5. Battery Lock 1b. Bolt Cutter Head 6. LED Work Light (white) 2. Retract Button 7. Trigger 3. LED Indicator (red) 8. Cutting Blades (EBS12ML) 4. Battery Cartridge Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 6: Specifications
Recommended Operating Temperature Range ....5 °F to 122 °F (–15 °C to 50 °C) Battery Charger .........Read the instructions supplied with the battery charger 52068603 Charger, 10.8 V lithium-ion batteries, 110 V Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 7: Battery And Charger
Remove the battery before unplugging the charger from the receptable to prevent the battery from discharging and potentially burning up. Failure to observe this precaution may result in injury and property damage. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... -
Page 8: Operation
Failure to wear eye protection could purpose only. result in serious eye injury from flying debris or hydraulic oil. Failure to observe these precautions may result in injury or property damage. Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070... - Page 9 The LED signals in areas. the following cases: Cutting Procedure—ES32ML and ES32FML 1. Insert the cable to be cut into the cutting head. 2. Pull the trigger to make the cut. When What it means 3.
-
Page 10: Maintenance
3. Inspect the rotation of the head assembly. Fully result in serious eye injury from retract the ram. The head should rotate no more flying debris or hydraulic oil. than 350°. If damage is detected, contact Greenlee customer service at 800-435-0786 for warranty service or repair. After use: 1. -
Page 11: Troubleshooting
Air in hydraulic system. Pull trigger and hold retract button simultaneously. Run for approximately 10 seconds, and then attempt to cut. If unsuccessful, contact Greenlee customer service at 800-435-0786 for warranty service or repair. Cold oil. Pull trigger and hold retract button simultaneously to warm oil. - Page 12 4455 Boeing Drive • Rockford, IL 61109-2988 • USA • 815-397-7070 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 ©2019 Greenlee Tools, Inc. • An ISO 9001 Company Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 www.greenlee.com...