Table 10: Ht488 Fxs Port S; Ettings Pages Definitions - Grandstream Networks HT-488 User Manual

T 10: HT488 FXS PORT S
ABLE
SIP Server
Outbound Proxy
SIP User ID
Authenticate ID
Authentication
Password
Name
Use DNS SRV:
User ID is Phone
Number
SIP Registration
Unregister on Reboot
Register Expiration
Local SIP port
Local RTP port
Use Random Port
SIP Registration
Failure Retry Wait
Time
DTMF Payload Type
Send DTMF
Grandstream Networks, Inc.
P D
ETTINGS AGES EFINITIONS
This field contains the URI string or the IP address (and port, if different from
5060) of the SIP proxy server. e.g., the following are some valid examples:
sip.my-VoIP-provider.com, or sip:my-company-sip-server.com, or
192.168.1.200:5066
IP address or Domain name of Outbound Proxy, or Media Gateway, or
Session Border Controller. Used by ATA for firewall or NAT penetration in
different network environment. If symmetric NAT is detected, STUN will not
work and ONLY Outbound Proxy will work.
User account information, provided by VoIP service provider (ITSP), usually
has the form of digit similar to phone number or actually a phone number. This
field contains the user part of the SIP address for this phone. e.g., if the SIP
address is sip:my_user_id@my_provider.com, then the SIP User ID is:
my_user_id.
Do NOT include the preceding "sip:" scheme or the host portion of the SIP
address in this field.
ID used for authentication, usually same as SIP user ID, but could be different
and decided by ITSP.
Password for ATA to register to (SIP) servers of ITSP. Purposely blank out
once saved for security. Maximum length is 25.
SIP service subscriber's name which will be used for Caller ID display
Default is No. If set to Yes the client will use DNS SRV to lookup for the SIP
server.
If "Yes" is set, a "user=phone" parameter will be attached to the "From"
header in SIP request
This parameter controls whether the HandyTone ATA needs to send
REGISTER messages to the proxy server. The default setting is "Yes".
Default is No. If set to yes, the device will first send registration request to
remove all previous bindings. Use only if proxy supports this remove bindings
request.
This parameter allows the user to specify the time frequency (in minutes) the
HandyTone ATA refreshes its registration with the specified registrar. The
default interval is 60 minutes (or 1 hour). The maximum interval is 65535
minutes (about 45 days).
This parameter defines the local SIP port the HandyTone ATA will listen and
transmit. The default value for FXS port is 5060.
This parameter defines the local RTP-RTCP port pair the HandyTone ATA will
listen and transmit. It is the base RTP port for channel 0. When configured,
channel 0 will use this port _value for RTP and the port_value+1 for its RTCP;
channel 1 will use port_value+2 for RTP and port_value+3 for its RTCP. The
default value for FXS port is 5004.
Default No. If set to Yes, the device will pick randomly-generated SIP and RTP
ports. This is usually necessary when multiple HandyTone ATAs are behind
the same NAT.
In case sip server fail from some reason, the HT488 will try to re-register not
according to standard SIP timers, but according to preconfigured interval.
Recommended to leave default value 20sec. Designed by special request of
big service providers.
This parameter sets the payload type for DTMF using RFC2833
This parameter specify the mechanism to transmit DTMF digit. There are 3
HT488 User Manual
Firmware 1.0.3.86
Page 23 of 31
Last Updated: 7/2007