Table of Contents
Advertisement
5 Repeat steps 3 to 4 to program a
sequence of up to five commands.
If you press RCU SETUP before programming is
completed, commands programmed up to that
point will be stored.
6 Press RCU SETUP to exit the
programming mode.
Using multi operations
1 Press MULTI OPERATION.
Release the button after the LED flashes once.
The LED continues to flash.
2 Within five seconds, press an input
function button that has been set up with
a multi operation.
The receiver switches on (if it was in standby)
and the programmed multi operation is per-
formed automatically.
Using System off
1 Press MULTI OPERATION.
Release the button after the LED flashes once.
The LED continues to flash.
2 Within five seconds, press u SOURCE.
The command sequence you programmed will
run, then all Pioneer components will switch
off, followed by this receiver (switch of all the
zones becomes off).
! In order to avoid accidently switching off a
DVD recorder that is currently recording, no
DVD recorder power off codes are sent.
Erasing the settings for the
multi-operation
This erases all the settings programmed in the
remote control for the multi-operation.
1 Press and hold RCU SETUP, then press
'8' for three seconds.
Release the button after the LED flashes once.
The LED continues to flash.
! To cancel the preset setup mode press
RCU SETUP.
2 Press the input function button
containing the program you want to
cancel or the u SOURCE button for three
seconds.
If the LED lights for one second, the erasing has
been successfully completed.
Resetting the remote control
settings
Use this procedure to reset all the remote con-
trol's settings to the factory default.
! When preset codes are set, all the signals
learned in the input function buttons are
cleared. This function is convenient when you
want to reset some but not all of input function
buttons.
1 Press and hold RCU SETUP, then press
'0' for three seconds.
Release the button after the LED flashes once.
The LED continues to flash.
2 Press and hold the ENTER button for
three seconds.
If the LED lights for one second, the erasing has
been successfully completed.
Default preset codes
Input function button
Preset code
DVD
2158
BD
2160
DVR/BDR
2150
2159
HDMI
TV/SAT
0116
CD
5066
TV CTRL
0116
Controlling components
This remote control can control components after entering the proper codes (see Setting the remote
to control other components on page 56 for more on this). Use the input function buttons to select
the component.
! The TV CONTROL buttons on the remote control are dedicated to control the TV assigned to the
TV CTRL button. If you have two TVs, assign the main TV to the TV CTRL button.
RECEIVER MULTI
PARAMETER
TOP MENU
BAND
PRESET
CATEGORY
iPod CTRL
AUTO / ALC /
SIGNAL SEL MCACC
CH LEVEL A.ATT
D.ACCESS
Controlling the rest of your system
SOURCE
OPERATION
RCU SETUP
BDR
BD
DVD
DVR
HDMI
SAT
TV
CD
HMG
ADPT
USB
OPTION
iPod
TUNER
SIRIUS
INPUT SELECT
TV CTRL
RECEIVER
MASTER
INPUT
VOLUME
TV CONTROL
CH
VOL
MUTE
AUDIO
VIDEO
PARAMETER
LIST
TUNE
TOOLS
T.EDIT
GUIDE
ENTER
PRESET
RETURN
HOME
TUNE
MENU
PGM
MEMORY
MENU
DIRECT
STEREO
STANDARD
ADV SURR
HDD
DVD
THX
PHASE CTRL
STATUS
TV / DTV
MPX
PQLS
HDMI OUT
AUDIO
1
2 2 2
3
SLEEP
INFO
4
5
6
DISP
DIMMER
7
8
9
CH
CLASS
0
/ CLR
ENTER
ZONE 2
ZONE 3
LIGHT
RECEIVER
10
59
En
Advertisement
Table of Contents
Troubleshooting
