Table of Contents
Advertisement
Operation with tape
S
V
Programming
HOW
IEW
ShowView greatly simplifies entering the date, channel,
start and end times of a Timer Recording by simply
entering a ShowView Code. ShowView Codes are pub-
lished in most TV guide magazines; they can vary one
to nine numbers in length.
S
V
is a registered trademark of Gemstar
HOW
IEW
Development Corporation.
The S
V
system is manufactured under license
HOW
IEW
from Gemstar Development Corporation.
1. Make sure that TV channels have been tuned and
S
V
stored in correct
HOW
Insert a video cassette with protection tab into your
DVD+VCR.
S
V
2. Press
.
HOW
IEW
SHOWVIEW NO.
- - - - - - -
REC
3. Press the numbered buttons to enter the
ShowView Code of the TV programme that you
wish to record. If you make a mistake press
enter the revised number.
SHOWVIEW NO.
246876543
REC
4. Press ENTER/OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong ShowView number, entered
the ShowView number incorrectly.
If "- -" is displayed, you have to enter the
programme number of the station, you want to
record from.
PR
DATE
PR-01
12
10
:
- -
- -
- - - - - - - -
:
- -
- -
- - - - - - - -
:
- -
- -
- - - - - - - -
:
- -
- -
- - - - - - - -
:
- -
- -
- - - - - - - -
:
- -
- -
- - - - - - - -
:
F
G
5. Press
or
to select the settings that you wish to
revise. (PR, DATE, TIME and SP).
Press
D
or
E
to enter the correct information.
PR
DATE
PR-01
12
10
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
order.
IEW
-
-
0~9,
OK i
F
then
DELETE :
0~9,
OK i
TIME
11 11 55
~
:
SP
~
:
SP
~
:
SP
~
:
SP
~
:
SP
~
:
SP
~
:
SP
i
TIME
:
11 11
~
:
55
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
i
6. Press
G
to select the recording speed.
Press
D
or
E
to select the desired tape speed (SP,
IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program.
Check that the timer event details are correct.
If you wish to record from AUDIO IN and VIDEO IN
on the front or from either of the EURO SCART
sockets on the back of VCR, press AV to select for
correct display (AV1, AV2 or AV3).
PR
DATE
PR-01
12
10
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
- -
- -
- - - - - - - -
7. If you want to make another ShowView recording
repeat stages 2 - 6. Press i twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press POWER to switch your VCR power off mode.
Note:
The 1W Mode is not available in the standby
mode for the timer recording.
will appear in the video recorder's display while
your VCR waits to make the recording.
To watch a DVD during timer recording standby
mode, press POWER and DVD to switch to DVD
mode.
8. Press POWER to end recording
TIME
:
11 11
~
:
55
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
:
~
:
SP
i
23
Advertisement
Table of Contents
