Table of Contents
Advertisement
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness level
of the signal to start the light
adjustment)
[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[MANUAL INTENSITY]
(Manual light source
adjsutment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[MULTI PROJECTOR SYNC]
Note
f [LIGHTS OUT SIGNAL LEVEL] cannot be set when [LIGHTS OUT TIMER] is set to [DISABLE].
f When [LIGHTS OUT TIMER] is set to anything other than [DISABLE], the following are the conditions to turn the light source back on again
from the state that the light source has turned off by this function.
g When the brightness level of the video signal being input has exceeded the value set in [LIGHTS OUT SIGNAL LEVEL]
g When the input signal is gone
g When on-screen display such as menu screen (OSD) or input guide, a test pattern, or a warning message is displayed
g When the operating environment temperature is around 0 °C (32 °F) and the light source is forced to turn on due to warm-up
f When the image of analog signal is projected, the image may be affected by the signal noise while the brightness level of the video signal is
detected. In this case, even when the brightness level of the image falls below the value set in [LIGHTS OUT SIGNAL LEVEL], it is judged
that the brightness level is not below the value as a signal.
Analog signal refers to Y/C signal, YC
f When [DYNAMIC GAMMA] is set to [3], the contrast will be maximized.
f The brightness control function and the dynamic contrast function will operate simultaneously, but the dynamic contrast function will not
operate while measuring the brightness and the color.
f The contrast synchronization function is a function to display a combined screen with a balanced contrast by sharing the brightness level of
the video signal input to each projector when a multi-display is constructed by combining the projected image of multiple projectors.
f The [3D SYNC SETTING] setting is disabled and fixed to [OFF] when [MULTI PROJECTOR SYNC] → [MODE] is set to anything other than
[OFF].
f The following settings are disabled and the contrast synchronization function and shutter synchronization function cannot be used when [3D
SYNC SETTING] is set to anything other than [OFF].
g The [PICTURE] menu → [DYNAMIC CONTRAST] → [USER] → [MULTI PROJECTOR SYNC]
g The [DISPLAY OPTION] menu → [SHUTTER SETTING] → [MULTI PROJECTOR SYNC]
g The [PROJECTOR SETUP] menu → [MULTI PROJECTOR SYNC]
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, but you can set the system method manually when an
unstable signal is input. Set the system method matching the input signal.
1)
Press as to select [SYSTEM SELECTOR].
2)
Press the <ENTER> button.
3)
Press as to select a system format.
f Select the system format using asqw when the signal is input to the <SDI IN 1>/<SDI IN 2> terminals.
f Available system formats vary depending on the input signal.
Chapter 4 Settings — [PICTURE] menu
Setting item
[6%] - [50%]
[DISABLE]
[0.0s] - [10.0s]
[0%] - [5%]
[0] - [255]
[OFF]
[1]
[2]
[3]
C
/YP
P
signal, and analog RGB signal.
B
R
B
R
Details
Adjusts the light source when the brightness level of the video
signal being input gets lower than the set value. The higher the
value, the larger the range to perform the light adjustment of the
light source.
Can be set in increments of 1 %. (Factory setting: 30 %)
Does not turn off the light source.
Turns off the light source when the brightness level of the video
signal being input goes under the value set in [LIGHTS OUT
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] -
[4.0s] can be selected in increments of 0.5.
Set the level of the brightness of the video signal to turn off the light
source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
The larger the value, the stronger the correction.
Can be set in increments of 1. (Factory setting: 255)
Does not compensate the signal.
Slightly compensates the signal.
Moderately compensates the signal.
Strongly compensates the signal.
Sets the contrast synchronization function.
This setting item is common with the following menu item.
f The [PROJECTOR SETUP] menu → [MULTI PROJECTOR
SYNC]
Refer to the [PROJECTOR SETUP] menu → [MULTI PROJECTOR
SYNC] (x page 142) for details.
ENGLISH - 91
Advertisement
Table of Contents
